[PATCH v4 23/31] mtd: nand: pxa3xx: Move the data buffer clean to prepare_start_command()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




To allow future support of multiple page reading/writing, move the data
buffer clean out of prepare_set_command().

This is done to prevent the data buffer from being cleaned on every command
preparation, when a multiple command sequence is implemented to read/write
pages larger than the FIFO size (2 KiB).

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@xxxxxxxxxxxxxxxxxx>
---
 drivers/mtd/nand/pxa3xx_nand.c | 21 ++++++++++++++++-----
 1 file changed, 16 insertions(+), 5 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index d3f3959..5f874a6 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -609,6 +609,9 @@ static void set_command_address(struct pxa3xx_nand_info *info,
 
 static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 {
+	struct pxa3xx_nand_host *host = info->host[info->cs];
+	struct mtd_info *mtd = host->mtd;
+
 	/* reset data and oob column point to handle data */
 	info->buf_start		= 0;
 	info->buf_count		= 0;
@@ -633,6 +636,19 @@ static void prepare_start_command(struct pxa3xx_nand_info *info, int command)
 		info->ndcb2 = 0;
 		break;
 	}
+
+	/*
+	 * If we are about to isse a read command, or about to set
+	 * the write address, then clean the data buffer.
+	 */
+	if (command == NAND_CMD_READ0 ||
+	    command == NAND_CMD_READOOB ||
+	    command == NAND_CMD_SEQIN) {
+
+		info->buf_count = mtd->writesize + mtd->oobsize;
+		memset(info->data_buff, 0xFF, info->buf_count);
+	}
+
 }
 
 static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
@@ -674,16 +690,11 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 			info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8);
 
 		set_command_address(info, mtd->writesize, column, page_addr);
-		info->buf_count = mtd->writesize + mtd->oobsize;
-		memset(info->data_buff, 0xFF, info->buf_count);
 		break;
 
 	case NAND_CMD_SEQIN:
 
 		set_command_address(info, mtd->writesize, column, page_addr);
-		info->buf_count = mtd->writesize + mtd->oobsize;
-		memset(info->data_buff, 0xFF, info->buf_count);
-
 		break;
 
 	case NAND_CMD_PAGEPROG:
-- 
1.8.1.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux