[PATCH v2 07/10] [media] tvp5150: Add device tree binding document

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Add a Device Tree binding document for the TVP5150 video decoder.

Signed-off-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

---

Changes in v2:
- Fix indentation of the DTS example. Suggested by Rob Herring.
- Rename powerdown-gpios to pdn-gpios to match the pin name in
  the datasheet. Suggested by Laurent Pinchart.
- Add optional properties for the video endpoint and list the supported
  values. Suggested by Laurent Pinchart.

 .../devicetree/bindings/media/i2c/tvp5150.txt      | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/tvp5150.txt

diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
new file mode 100644
index 000000000000..8c0fc1a26bf0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -0,0 +1,45 @@
+* Texas Instruments TVP5150 and TVP5151 video decoders
+
+The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+Required Properties:
+- compatible: value must be "ti,tvp5150"
+- reg: I2C slave address
+
+Optional Properties:
+- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
+- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Endpoint Properties for parallel synchronization:
+
+- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
+- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
+- field-even-active: field signal level during the even field data
+  transmission. Must be <0>.
+
+If none of hsync-active, vsync-active and field-even-active is specified,
+the endpoint is assumed to use embedded BT.656 synchronization.
+
+Example:
+
+&i2c2 {
+	...
+	tvp5150@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+
+		port {
+			tvp5150_1: endpoint {
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};
-- 
2.4.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux