Re: [PATCH v2 1/2] ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Marcel,

On 2016-01-05 08:39, Marcel Ziswiler wrote:
> From: Petr Štetiar <ynezz@xxxxxxx>
> 
> Signed-off-by: Petr Štetiar <ynezz@xxxxxxx>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx>
> ---
> 
> Changes in v2:
> - clarify exact Apalis iMX6Q/D SoM type in cover letter
> - clarify exact Apalis iMX6Q/D module type and Ixora carrier board in model
>   node
> - got rid of obsolete mmc aliases
> - working SGTL5000 audio/sound integration
> - working STMPE811 touch screen controller integration
> - integrated review feedback from Lucas
> - left and even added some more comments as I don't see why putting any
>   explanatory comments in dts' should be such a bad thing to do
> - completely got rid of the memory node as that is something typically filled
>   in by the boot loader e.g. U-Boot
> - without the regulators simple-bus it no longer boots
> - even though we supposedly shipped a few hundred V1.0a modules drop DCE UART
>   support for now and simplify file layout
> - replaced obsolete no-1-8-v by mainline supported voltage-ranges = <3300 3300>
>   usdhc property and yes card detects are indeed active low (;-p)
> - integrated review feedback from Stefan
> - fixed Ethernet PHY reset & interrupt (requires Micrel PHY driver to be
>   enabled)
> - fixed HDMI DDC (requires GPIO-based bitbanging I2C to be enabled)
> - fixed SPDIF
> 
>  arch/arm/boot/dts/imx6qdl-apalis.dtsi | 1040 +++++++++++++++++++++++++++++++++
>  1 file changed, 1040 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6qdl-apalis.dtsi
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> new file mode 100644
> index 0000000..6104e2e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> @@ -0,0 +1,1040 @@
> +/*
> + * Copyright 2014-2016 Toradex AG
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Toradex Apalis iMX6Q/D Module";
> +	compatible = "toradex,apalis_imx6q", "fsl,imx6q";
> +
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm4 0 5000000>;
> +		status = "disabled";
> +	};
> +
> +	/* DDC_I2C: I2C2_SDA/SCL on MXM3 205/207 */
> +	i2cddc: i2c@0 {
> +		compatible = "i2c-gpio";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_i2c_ddc>;
> +		gpios = <&gpio3 16 GPIO_ACTIVE_HIGH /* sda */
> +			 &gpio2 30 GPIO_ACTIVE_HIGH /* scl */
> +			>;
> +		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
> +		status = "okay";
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +
> +		reg_1p8v: 1p8v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "1P8V";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_2p5v: 2p5v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "2P5V";
> +			regulator-min-microvolt = <2500000>;
> +			regulator-max-microvolt = <2500000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_3p3v: 3p3v {
> +			compatible = "regulator-fixed";
> +			regulator-name = "3P3V";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_usb_otg_vbus: usb_otg_vbus {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
> +			regulator-name = "usb_otg_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +			status = "disabled";
> +		};
> +
> +		/* on module usb hub */
> +		reg_usb_host_vbus_hub: usb_host_vbus_hub {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
> +			regulator-name = "usb_host_vbus_hub";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
> +			startup-delay-us = <2000>;
> +			enable-active-high;
> +			status = "okay";
> +		};
> +
> +		reg_usb_host_vbus: usb_host_vbus {
> +			compatible = "regulator-fixed";
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
> +			regulator-name = "usb_host_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +			vin-supply = <&reg_usb_host_vbus_hub>;
> +			status = "disabled";
> +		};
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx-audio-sgtl5000";
> +		model = "imx6q-apalis-sgtl5000";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&codec>;
> +		audio-routing =
> +			"LINE_IN", "Line In Jack",
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"Headphone Jack", "HP_OUT";
> +		mux-int-port = <1>;
> +		mux-ext-port = <4>;
> +	};
> +
> +	sound_spdif: sound-spdif {
> +		compatible = "fsl,imx-audio-spdif";
> +		model = "imx-spdif";
> +		spdif-controller = <&spdif>;
> +		spdif-in;
> +		spdif-out;
> +		status = "disabled";
> +	};
> +};
> +
> +&audmux {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_audmux &pinctrl_audmux_mclk>;
> +	status = "okay";
> +};
> +
> +/* Apalis SPI1 */
> +&ecspi1 {
> +	fsl,spi-num-chipselects = <1>;
> +	cs-gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_spi_cs1>;
> +	status = "disabled";
> +};
> +
> +/* Apalis SPI2 */
> +&ecspi2 {
> +	fsl,spi-num-chipselects = <1>;
> +	cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_spi_cs2>;
> +	status = "disabled";
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet &pinctrl_enet_ctrl>;
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy>;
> +	phy-reset-duration = <10>;
> +	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy: ethernet-phy@7 {
> +			interrupt-parent = <&gpio1>;
> +			interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
> +			reg = <7>;
> +		};
> +	};
> +};
> +
> +&can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	status = "disabled";
> +};
> +
> +&can2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan2>;
> +	status = "disabled";
> +};
> +
> +&hdmi {
> +	ddc-i2c-bus = <&i2cddc>;
> +	status = "okay";
> +};
> +
> +/*
> + * GEN1_I2C: I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier
> + * board)
> + */
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "disabled";
> +};
> +
> +&i2c2 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +
> +	pmic: pfuze100@08 {
> +		compatible = "fsl,pfuze100";
> +		reg = <0x08>;
> +
> +		regulators {
> +			sw1a_reg: sw1ab {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw1c_reg: sw1c {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw3a_reg: sw3a {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			swbst_reg: swbst {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5150000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			snvs_reg: vsnvs {
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vref_reg: vrefddr {
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen1_reg: vgen1 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen2_reg: vgen2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen3_reg: vgen3 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen4_reg: vgen4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen5_reg: vgen5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen6_reg: vgen6 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +
> +	codec: sgtl5000@0a {
> +		compatible = "fsl,sgtl5000";
> +		reg = <0x0a>;
> +		clocks = <&clks 201>;
> +		VDDA-supply = <&reg_2p5v>;
> +		VDDIO-supply = <&reg_3p3v>;

Nit: The device tree bindings mention two more properties as required
properties:
micbias-resistor-k-ohms
micbias-voltage-m-volts

However, both have "If this node is not mentioned", hence I guess they
are actually optional, but maybe we want to set an explicit value here?


> +	};
> +
> +	/* STMPE811 touch screen controller */
> +	stmpe811@41 {
> +		compatible = "st,stmpe811";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_touch_int>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0x41>;
> +		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-parent = <&gpio4>;
> +		interrupt-controller;
> +		id = <0>;
> +		blocks = <0x5>;
> +		irq-trigger = <0x1>;
> +		stmpe_touchscreen {
> +			compatible = "st,stmpe-ts";
> +			reg = <0>;
> +			/* 3.25 MHz ADC clock speed */
> +			st,adc-freq = <1>;
> +			/* 8 sample average control */
> +			st,ave-ctrl = <3>;
> +			/* 7 length fractional part in z */
> +			st,fraction-z = <7>;
> +			/*
> +			 * 50 mA typical 80 mA max touchscreen drivers
> +			 * current limit value
> +			 */
> +			st,i-drive = <1>;
> +			/* 12-bit ADC */
> +			st,mod-12b = <1>;
> +			/* internal ADC reference */
> +			st,ref-sel = <0>;
> +			/* ADC converstion time: 80 clocks */
> +			st,sample-time = <4>;
> +			/* 1 ms panel driver settling time */
> +			st,settling = <3>;
> +			/* 5 ms touch detect interrupt delay */
> +			st,touch-det-delay = <5>;
> +		};
> +	};
> +};
> +
> +/*
> + * GEN2_I2C, CAM: I2C3_SDA/SCL on MXM3 201/203 (unused)
> + */
> +&i2c3 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default", "recovery";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	pinctrl-1 = <&pinctrl_i2c3_recovery>;
> +	scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
> +	sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
> +	status = "disabled";
> +};
> +
> +/* PAD Ctrl values for common settings */
> +/*
> + * (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | PAD_CTL_PKE |
> + *  PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
> + */
> +#define PAD_CTRL_HYS_PU 0x1b0b0
> +
> +/*
> + * (PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED |
> + *  PAD_CTL_DSE_40ohm)
> + */
> +#define PAD_CTRL_HYS_PD 0x130b0
> +
> +/*
> + * (PAD_CTL_PUS_22K_UP | PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_LOW |
> + *  PAD_CTL_DSE_80ohm)
> + */
> +#define PAD_CTRL_PU_22k 0x0f058
> +
> +&iomuxc {

I think it is a convention to move iomuxc at the very end for better
readability of the rest. At least the Vybrid dts and the more recently
added imx7d-sdb.dts follow this rule.

> +	ecspi {
> +		pinctrl_ecspi1: ecspi1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x100b1
> +				MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x100b1
> +				MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x100b1
> +			>;
> +		};
> +		pinctrl_ecspi2: ecspi2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> +				MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> +				MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> +			>;
> +		};
> +		pinctrl_spi_cs1: spi_cs1 {
> +			fsl,pins = <
> +				/* SPI1 cs */
> +				MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25	0x000b1
> +			>;
> +		};
> +		pinctrl_spi_cs2: spi_cs2 {
> +			fsl,pins = <
> +				/* SPI2 cs */
> +				MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x000b1
> +			>;
> +		};
> +	};
> +
> +	flexcan {
> +		pinctrl_flexcan1: flexcan1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
> +				MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
> +			>;
> +		};
> +		pinctrl_flexcan2: flexcan2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
> +				MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
> +			>;
> +		};
> +	};
> +
> +	gpio {
> +		pinctrl_apalis_gpio1: apalis_gpio1 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_D4__GPIO2_IO04 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio2: apalis_gpio2 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_D5__GPIO2_IO05 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio3: apalis_gpio3 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_D6__GPIO2_IO06 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio4: apalis_gpio4 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_D7__GPIO2_IO07 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio5: apalis_gpio5 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio6: apalis_gpio6 {
> +			fsl,pins = <
> +				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09
> +						PAD_CTRL_HYS_PD

The 80 character limit normally is not enforced for device trees, hence
I would remove that line break here...

> +			>;
> +		};
> +		pinctrl_apalis_gpio7: apalis_gpio7 {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_2__GPIO1_IO02 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_apalis_gpio8: apalis_gpio8 {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_6__GPIO1_IO06 PAD_CTRL_HYS_PD
> +			>;
> +		};
> +		pinctrl_gpio_keys: gpio_keys {
> +			fsl,pins = <
> +				/* Power Button */
> +				MX6QDL_PAD_GPIO_4__GPIO1_IO04 PAD_CTRL_HYS_PU
> +			>;
> +		};
> +	};
> +
> +	hdmi {
> +		pinctrl_hdmi_cec: hdmicecgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> +			>;
> +		};
> +	};
> +
> +	i2c {
> +		pinctrl_i2c_ddc: i2c_ddc {
> +			fsl,pins = <
> +				/* DDC bitbang */
> +				MX6QDL_PAD_EIM_EB2__GPIO2_IO30 PAD_CTRL_HYS_PU
> +				MX6QDL_PAD_EIM_D16__GPIO3_IO16 PAD_CTRL_HYS_PU
> +			>;
> +		};
> +		pinctrl_i2c1: i2c1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> +				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> +			>;
> +		};
> +		pinctrl_i2c3: i2c3grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> +				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> +			>;
> +		};
> +		pinctrl_i2c3_recovery: i2c3-recoverygrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x4001b8b1
> +				MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x4001b8b1
> +			>;
> +		};
> +	};
> +
> +	/* pins used on module */
> +	imx6q-apalis {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reset_moci &pinctrl_emmc_reset>;
> +		pinctrl_audmux: audmuxgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_DISP0_DAT20__AUD4_TXC	0x130b0
> +				MX6QDL_PAD_DISP0_DAT21__AUD4_TXD	0x130b0
> +				MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS	0x130b0
> +				MX6QDL_PAD_DISP0_DAT23__AUD4_RXD	0x130b0
> +			>;
> +		};
> +		pinctrl_audmux_mclk: audmux_mclk {
> +			fsl,pins = <
> +				/* SGTL5000 sys_mclk */
> +				MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
> +			>;
> +		};
> +		pinctrl_emmc_reset: emmc_reset {
> +			fsl,pins = <
> +				/* eMMC reset, leave it alone */
> +				MX6QDL_PAD_SD3_RST__GPIO7_IO08 PAD_CTRL_PU_22k
> +			>;
> +		};
> +		pinctrl_enet: enetgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
> +				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
> +				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
> +				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
> +				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
> +				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
> +				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
> +				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
> +				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
> +				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
> +				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
> +				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
> +				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
> +				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
> +				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
> +			>;
> +		};
> +		pinctrl_enet_ctrl: enet_ctrlgrp {
> +			fsl,pins = <
> +				/* Ethernet PHY reset */
> +				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x000b0
> +				/* Ethernet PHY interrupt */
> +				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x000b1
> +			>;
> +		};
> +		pinctrl_i2c2: i2c2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> +				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> +			>;
> +		};
> +		pinctrl_ipu2_vdac: ipu2vdacgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK 0xd1
> +				MX6QDL_PAD_DI0_PIN15__IPU2_DI0_PIN15       0xd1
> +				MX6QDL_PAD_DI0_PIN2__IPU2_DI0_PIN02        0xd1
> +				MX6QDL_PAD_DI0_PIN3__IPU2_DI0_PIN03        0xd1
> +				MX6QDL_PAD_DISP0_DAT0__IPU2_DISP0_DATA00   0xf9
> +				MX6QDL_PAD_DISP0_DAT1__IPU2_DISP0_DATA01   0xf9
> +				MX6QDL_PAD_DISP0_DAT2__IPU2_DISP0_DATA02   0xf9
> +				MX6QDL_PAD_DISP0_DAT3__IPU2_DISP0_DATA03   0xf9
> +				MX6QDL_PAD_DISP0_DAT4__IPU2_DISP0_DATA04   0xf9
> +				MX6QDL_PAD_DISP0_DAT5__IPU2_DISP0_DATA05   0xf9
> +				MX6QDL_PAD_DISP0_DAT6__IPU2_DISP0_DATA06   0xf9
> +				MX6QDL_PAD_DISP0_DAT7__IPU2_DISP0_DATA07   0xf9
> +				MX6QDL_PAD_DISP0_DAT8__IPU2_DISP0_DATA08   0xf9
> +				MX6QDL_PAD_DISP0_DAT9__IPU2_DISP0_DATA09   0xf9
> +				MX6QDL_PAD_DISP0_DAT10__IPU2_DISP0_DATA10  0xf9
> +				MX6QDL_PAD_DISP0_DAT11__IPU2_DISP0_DATA11  0xf9
> +				MX6QDL_PAD_DISP0_DAT12__IPU2_DISP0_DATA12  0xf9
> +				MX6QDL_PAD_DISP0_DAT13__IPU2_DISP0_DATA13  0xf9
> +				MX6QDL_PAD_DISP0_DAT14__IPU2_DISP0_DATA14  0xf9
> +				MX6QDL_PAD_DISP0_DAT15__IPU2_DISP0_DATA15  0xf9
> +			>;
> +		};
> +		pinctrl_regulator_usbhub_pwr: gpio_regulator_usbhub_pwr {
> +			fsl,pins = <
> +				/* USBH_HUB_EN */
> +				MX6QDL_PAD_EIM_D28__GPIO3_IO28 PAD_CTRL_PU_22k
> +			>;
> +		};
> +		pinctrl_reset_moci: gpio_reset_moci {
> +			fsl,pins = <
> +				/* RESET_MOCI control */
> +				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28
> +						PAD_CTRL_PU_22k
> +			>;
> +		};
> +		pinctrl_touch_int: touch_intgrp {
> +			fsl,pins = <
> +				/* STMPE811 interrupt */
> +				MX6QDL_PAD_KEY_COL2__GPIO4_IO10 PAD_CTRL_HYS_PU
> +			>;
> +		};
> +		pinctrl_usdhc3: usdhc3grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
> +				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
> +				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> +				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> +				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> +				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> +				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> +				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> +				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> +				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> +			>;
> +		};
> +		pinctrl_usdhc3_100mhz: usdhc3grp-100mhz { /* 100Mhz */

I do not have a strong opinion on comments, but if they are pure
duplication of what is already there, I kind of prefer to not add
them...

> +			fsl,pins = <
> +				MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170B9
> +				MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100B9
> +				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B9
> +				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B9
> +				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B9
> +				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B9
> +				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170B9
> +				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170B9
> +				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170B9
> +				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170B9
> +			>;
> +		};
> +		pinctrl_usdhc3_200mhz: usdhc3grp-200mhz { /* 200Mhz */
> +			fsl,pins = <
> +				MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170F9
> +				MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100F9
> +				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
> +				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
> +				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
> +				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
> +				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170F9
> +				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170F9
> +				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170F9
> +				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170F9
> +			>;
> +		};
> +	};
> +
> +	ipu1 {
> +		pinctrl_ipu1_lcdif: ipu1lcdifgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_A16__IPU1_DI1_DISP_CLK	0x61
> +				/* DE */
> +				MX6QDL_PAD_EIM_DA10__IPU1_DI1_PIN15	0x61
> +				/* HSync */
> +				MX6QDL_PAD_EIM_DA11__IPU1_DI1_PIN02	0x61
> +				/* VSync */
> +				MX6QDL_PAD_EIM_DA12__IPU1_DI1_PIN03	0x61
> +				MX6QDL_PAD_EIM_DA9__IPU1_DISP1_DATA00	0x61
> +				MX6QDL_PAD_EIM_DA8__IPU1_DISP1_DATA01	0x61
> +				MX6QDL_PAD_EIM_DA7__IPU1_DISP1_DATA02	0x61
> +				MX6QDL_PAD_EIM_DA6__IPU1_DISP1_DATA03	0x61
> +				MX6QDL_PAD_EIM_DA5__IPU1_DISP1_DATA04	0x61
> +				MX6QDL_PAD_EIM_DA4__IPU1_DISP1_DATA05	0x61
> +				MX6QDL_PAD_EIM_DA3__IPU1_DISP1_DATA06	0x61
> +				MX6QDL_PAD_EIM_DA2__IPU1_DISP1_DATA07	0x61
> +				MX6QDL_PAD_EIM_DA1__IPU1_DISP1_DATA08	0x61
> +				MX6QDL_PAD_EIM_DA0__IPU1_DISP1_DATA09	0x61
> +				MX6QDL_PAD_EIM_EB1__IPU1_DISP1_DATA10	0x61
> +				MX6QDL_PAD_EIM_EB0__IPU1_DISP1_DATA11	0x61
> +				MX6QDL_PAD_EIM_A17__IPU1_DISP1_DATA12	0x61
> +				MX6QDL_PAD_EIM_A18__IPU1_DISP1_DATA13	0x61
> +				MX6QDL_PAD_EIM_A19__IPU1_DISP1_DATA14	0x61
> +				MX6QDL_PAD_EIM_A20__IPU1_DISP1_DATA15	0x61
> +				MX6QDL_PAD_EIM_A21__IPU1_DISP1_DATA16	0x61
> +				MX6QDL_PAD_EIM_A22__IPU1_DISP1_DATA17	0x61
> +				MX6QDL_PAD_EIM_A23__IPU1_DISP1_DATA18	0x61
> +				MX6QDL_PAD_EIM_A24__IPU1_DISP1_DATA19	0x61
> +				MX6QDL_PAD_EIM_D31__IPU1_DISP1_DATA20	0x61
> +				MX6QDL_PAD_EIM_D30__IPU1_DISP1_DATA21	0x61
> +				MX6QDL_PAD_EIM_D26__IPU1_DISP1_DATA22	0x61
> +				MX6QDL_PAD_EIM_D27__IPU1_DISP1_DATA23	0x61
> +			>;
> +		};
> +		pinctrl_cam_mclk: cam_mclk {
> +			fsl,pins = <
> +				/* CAM sys_mclk */
> +				MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x00b0
> +			>;
> +		};
> +		pinctrl_ipu1_csi0: ipu1csi0grp { /* parallel camera */
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0xb0b1
> +				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0xb0b1
> +				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0xb0b1
> +				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0xb0b1
> +				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0xb0b1
> +			>;
> +		};
> +	};
> +
> +	pwm {
> +		pinctrl_pwm1: pwm1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
> +			>;
> +		};
> +		pinctrl_pwm2: pwm2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
> +			>;
> +		};
> +		pinctrl_pwm3: pwm3grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> +			>;
> +		};
> +		pinctrl_pwm4: pwm4grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	spdif {
> +		pinctrl_spdif: spdifgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_GPIO_16__SPDIF_IN  0x1b0b0
> +				MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
> +			>;
> +		};
> +	};
> +
> +	uart1 {
> +		pinctrl_uart1_dce: uart1-dcegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> +			>;
> +		};
> +
> +		/* DTE mode */
> +		pinctrl_uart1_dte: uart1-dtegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x1b0b1
> +				MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x1b0b1
> +				MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x1b0b1
> +			>;
> +		};
> +
> +		/* Additional DTR, DSR, DCD */
> +		pinctrl_uart1_ctrl: uart1-ctrlgrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
> +				MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
> +				MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
> +			>;
> +		};
> +	};
> +
> +	uart2 {
> +		pinctrl_uart2_dce: uart2-dcegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
> +				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
> +			>;
> +		};
> +
> +		/* DTE mode */
> +		pinctrl_uart2_dte: uart2grp-dte {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA	0x1b0b1
> +				MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
> +				MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
> +				MX6QDL_PAD_SD4_DAT5__UART2_CTS_B	0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	uart4 {
> +		pinctrl_uart4_dce: uart4-dcegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> +			>;
> +		};
> +
> +		/* DTE mode */
> +		pinctrl_uart4_dte: uart4-dtegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL0__UART4_RX_DATA 0x1b0b1
> +				MX6QDL_PAD_KEY_ROW0__UART4_TX_DATA 0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	uart5 {
> +		pinctrl_uart5_dce: uart5-dcegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> +				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> +			>;
> +		};
> +
> +		/* DTE mode */
> +		pinctrl_uart5_dte: uart5-dtegrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_KEY_COL1__UART5_RX_DATA 0x1b0b1
> +				MX6QDL_PAD_KEY_ROW1__UART5_TX_DATA 0x1b0b1
> +			>;
> +		};
> +	};
> +
> +	usbh {
> +		pinctrl_regulator_usbh_pwr: gpio_regulator_usbh_pwr {
> +			fsl,pins = <
> +				/* USBH_EN */
> +				MX6QDL_PAD_GPIO_0__GPIO1_IO00 PAD_CTRL_PU_22k
> +			>;
> +		};
> +	};
> +
> +	usbotg {
> +		pinctrl_usbotg: usbotggrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> +			>;
> +		};
> +		pinctrl_regulator_usbotg_pwr: gpio_regulator_usbotg_pwr {
> +			fsl,pins = <
> +				/* USBO power en */
> +				MX6QDL_PAD_EIM_D22__GPIO3_IO22 PAD_CTRL_PU_22k
> +			>;
> +		};
> +	};
> +
> +	usdhc {
> +		pinctrl_mmc_cd: gpio_mmc_cd {
> +			fsl,pins = <
> +				 /* MMC1 CD */
> +				MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
> +			>;
> +		};
> +		pinctrl_sd_cd: gpio_sd_cd {
> +			fsl,pins = <
> +				/* SD1 CD */
> +				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
> +			>;
> +		};
> +		pinctrl_usdhc1: usdhc1grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
> +				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
> +				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> +				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> +				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> +				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> +				MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
> +				MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
> +				MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x17071
> +				MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x17071
> +			>;
> +		};
> +		pinctrl_usdhc2: usdhc2grp {
> +			fsl,pins = <
> +				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17071
> +				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10071
> +				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17071
> +				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17071
> +				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17071
> +				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17071
> +			>;
> +		};
> +	};
> +};
> +
> +&ldb {
> +	status = "okay";
> +};
> +
> +&pwm1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm1>;
> +	status = "disabled";
> +};
> +
> +&pwm2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm2>;
> +	status = "disabled";
> +};
> +
> +&pwm3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm3>;
> +	status = "disabled";
> +};
> +
> +&pwm4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm4>;
> +	status = "disabled";
> +};
> +
> +&spdif {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spdif>;
> +	status = "disabled";
> +};
> +
> +&ssi1 {
> +	fsl,mode = "i2s-slave";
> +	status = "okay";
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
> +	fsl,dte-mode;
> +	fsl,uart-has-rtscts;
> +	status = "disabled";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2_dte>;
> +	fsl,dte-mode;
> +	fsl,uart-has-rtscts;
> +	status = "disabled";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4_dte>;
> +	fsl,dte-mode;
> +	status = "disabled";
> +};
> +
> +&uart5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart5_dte>;
> +	fsl,dte-mode;
> +	status = "disabled";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&reg_usb_host_vbus>;
> +	status = "disabled";
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usb_otg_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg>;
> +	disable-over-current;
> +	status = "disabled";
> +};
> +
> +/* MMC1 */
> +&usdhc1 {
> +	label = "MMC1";

This...

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
> +	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
> +	vmmc-supply = <&reg_3p3v>;
> +	bus-width = <8>;
> +	voltage-ranges = <3300 3300>;
> +	status = "disabled";
> +};
> +
> +/* SD1 */
> +&usdhc2 {
> +	label = "SD1";

...and this seem not to be specified upstream? (at least not in
Documentation/devicetree/bindings/mmc/mmc.txt?)
Not sure about this... Or is label a common convention and hence
available for all nodes?

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
> +	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
> +	vmmc-supply = <&reg_3p3v>;
> +	bus-width = <4>;
> +	voltage-ranges = <3300 3300>;
> +	status = "disabled";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	vmmc-supply = <&reg_3p3v>;
> +	bus-width = <8>;
> +	voltage-ranges = <3300 3300>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&weim {
> +	status = "disabled"; /* weim signals not accessible on i.MX6 */

They are accessible on the i.MX6 SoC.. but maybe "on Apalis iMX6Q/D". Or
just remove the comment, since that is kind of what disabled says?

> +};

Otherwise:
Reviewed-by: Stefan Agner <stefan@xxxxxxxx>

--
Stefan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux