Re: [PATCH V4] ARM: dts: imx6q-icore-rqs: Add Engicam IMX6 Q7 initial support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi

Sorry I mess up the email ;). Need to resend. Drop this one

On Thu, Dec 24, 2015 at 10:06 AM, Michael Trimarchi
<michael@xxxxxxxxxxxxxxxxxxxx> wrote:
> www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
>
> Signed-off-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> ---
> Test on top of ARM: dts: imx6q: clean up unused ipu2grp
>
> Changes in v4:
> - update regulator name
> - using flat pins,fsl
> - move iomuxc
> - add X11 license
> - better alphabetic order
>
> Changes in v3:
> - add sgtl audio support
> - add ethernet gigabit tuning
> - use hub reset only in usbhub and not
>  in otg vbus
>
> Changes in v2:
> - add the board in alphabetic order
> - remove cpu operating point
> - remove simple-bus and adjust regulaotor
> - add gpios to correct pinctrl
> - remove no mainline binding of gpc
>
>  arch/arm/boot/dts/Makefile               |   1 +
>  arch/arm/boot/dts/imx6q-icore-rqs.dts    |  78 ++++++
>  arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++
>  3 files changed, 489 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts
>  create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bb8fa02..7e8f29c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>         imx6q-gw551x.dtb \
>         imx6q-gw552x.dtb \
>         imx6q-hummingboard.dtb \
> +       imx6q-icore-rqs.dtb \
>         imx6q-nitrogen6x.dtb \
>         imx6q-phytec-pbab01.dtb \
>         imx6q-rex-pro.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> new file mode 100644
> index 0000000..0053188
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> @@ -0,0 +1,78 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-icore-rqs.dtsi"
> +
> +/ {
> +       model = "Engicam i.CoreM6 Quad SOM";
> +       compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
> +
> +       sound {
> +               compatible = "fsl,imx-audio-sgtl5000";
> +               model = "imx-audio-sgtl5000";
> +               ssi-controller = <&ssi1>;
> +               audio-codec = <&codec>;
> +               audio-routing =
> +                       "MIC_IN", "Mic Jack",
> +                       "Mic Jack", "Mic Bias",
> +                       "Headphone Jack", "HP_OUT";
> +               mux-int-port = <1>;
> +               mux-ext-port = <4>;
> +       };
> +};
> +
> +&i2c3 {
> +       codec: sgtl5000@0a {
> +               compatible = "fsl,sgtl5000";
> +               reg = <0x0a>;
> +               clocks = <&clks IMX6QDL_CLK_CKO>;
> +               VDDA-supply = <&reg_2p5v>;
> +               VDDIO-supply = <&reg_3p3v>;
> +               VDDD-supply = <&reg_1p8v>;
> +       };
> +};
> +
> +&sata {
> +       status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> new file mode 100644
> index 0000000..b984128
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> @@ -0,0 +1,410 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> +
> +/ {
> +       memory {
> +               reg = <0x10000000 0x80000000>;
> +       };
> +
> +       reg_1p8v: regulator-1p8v {
> +               compatible = "regulator-fixed";
> +               regulator-name = "1P8V";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       reg_2p5v: regulator-2p5v {
> +               compatible = "regulator-fixed";
> +               regulator-name = "2P5V";
> +               regulator-min-microvolt = <2500000>;
> +               regulator-max-microvolt = <2500000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       reg_3p3v: regulator-3p3v {
> +               compatible = "regulator-fixed";
> +               regulator-name = "3P3V";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       reg_sd3_vmmc: sd3-vmmc {
> +               compatible = "regulator-fixed";
> +               regulator-name = "P3V3_SD3_SWITCHED";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
> +               enable-active-high;
> +       };
> +
> +       reg_sd4_vmmc: sd4-vmmc {
> +               compatible = "regulator-fixed";
> +               regulator-name = "P3V3_SD4_SWITCHED";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       reg_usb_h1_vbus: usb-h1-vbus {
> +               compatible = "regulator-fixed";
> +               regulator-name = "usb_h1_vbus";
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       reg_usb_otg_vbus: usb-otg-vbus {
> +               compatible = "regulator-fixed";
> +               regulator-name = "usb_otg_vbus";
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       usb_hub: usb-hub {
> +               compatible = "smsc,usb3503a";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_usbhub>;
> +               reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> +               clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
> +               clock-names = "refclk";
> +       };
> +};
> +
> +&clks {
> +       assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
> +       assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
> +};
> +
> +&audmux {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_audmux>;
> +       status = "okay";
> +};
> +
> +&fec {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_enet_3>;
> +       phy-handle = <&eth_phy>;
> +       phy-mode = "rgmii";
> +       status = "okay";
> +       mdio {
> +               eth_phy: ethernet-phy {
> +                       rxc-skew-ps = <1140>;
> +                       txc-skew-ps = <1140>;
> +                       txen-skew-ps = <600>;
> +                       rxdv-skew-ps = <240>;
> +                       rxd0-skew-ps = <420>;
> +                       rxd1-skew-ps = <600>;
> +                       rxd2-skew-ps = <420>;
> +                       rxd3-skew-ps = <240>;
> +                       txd0-skew-ps = <60>;
> +                       txd1-skew-ps = <60>;
> +                       txd2-skew-ps = <60>;
> +                       txd3-skew-ps = <240>;
> +               };
> +       };
> +};
> +
> +&i2c1 {
> +       clock-frequency = <100000>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c1_1>;
> +       status = "okay";
> +};
> +
> +&i2c2 {
> +       clock-frequency = <100000>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c2_2>;
> +       status = "okay";
> +};
> +
> +&i2c3 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c3_4>;
> +       status = "okay";
> +};
> +
> +&pcie {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_pcie>;
> +       reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
> +       status = "okay";
> +};
> +
> +&ssi1 {
> +       fsl,mode = "i2s-slave";
> +       status = "okay";
> +};
> +
> +&uart4 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_uart4_1>;
> +       status = "okay";
> +};
> +
> +&usbh1 {
> +       vbus-supply = <&reg_usb_h1_vbus>;
> +       disable-over-current;
> +       clocks = <&clks IMX6QDL_CLK_USBOH3>;
> +       status = "okay";
> +};
> +
> +&usbotg {
> +       vbus-supply = <&reg_usb_otg_vbus>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_usbotg_2>;
> +       disable-over-current;
> +       status = "okay";
> +};
> +
> +&usdhc1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_usdhc1_1>;
> +       no-1-8-v;
> +       status = "okay";
> +};
> +
> +&usdhc3 {
> +       pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +       pinctrl-0 = <&pinctrl_usdhc3_2>;
> +       pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
> +       pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
> +       vmcc-supply = <&reg_sd3_vmmc>;
> +       cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> +       bus-witdh=<4>;
> +       no-1-8-v;
> +       status = "okay";
> +};
> +
> +&usdhc4 {
> +       pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +       pinctrl-0 = <&pinctrl_usdhc4_1>;
> +       pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
> +       pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
> +       vmcc-supply = <&reg_sd4_vmmc>;
> +       bus-witdh=<8>;
> +       no-1-8-v;
> +       non-removable;
> +       status = "okay";
> +};
> +
> +&iomuxc {
> +       pinctrl_audmux: audmux {
> +               fsl,pins = <
> +                       MX6QDL_PAD_DISP0_DAT20__AUD4_TXC  0x130b0
> +                       MX6QDL_PAD_DISP0_DAT21__AUD4_TXD  0x110b0
> +                       MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> +                       MX6QDL_PAD_DISP0_DAT23__AUD4_RXD  0x130b0
> +               >;
> +       };
> +
> +       pinctrl_enet_3: enetgrp-3 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
> +                       MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
> +                       MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0x1b0b0
> +                       MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0x1b0b0
> +                       MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0x1b0b0
> +                       MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0x1b0b0
> +                       MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0x1b0b0
> +                       MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> +                       MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
> +                       MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
> +                       MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
> +                       MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
> +                       MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
> +                       MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
> +                       MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> +                       MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN     0x1b0b0
> +               >;
> +       };
> +
> +       pinctrl_i2c1_1: i2c1grp-1 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> +                       MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> +               >;
> +       };
> +
> +       pinctrl_i2c2_2: i2c2grp-2 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> +                       MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> +               >;
> +       };
> +
> +       pinctrl_i2c3_4: i2c3grp-4 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
> +                       MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> +                       MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x130b0
> +               >;
> +       };
> +
> +       pinctrl_pcie: pciegrp {
> +               fsl,pins = <
> +                       MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059  /* PCIe Reset */
> +               >;
> +       };
> +
> +       pinctrl_uart4_1: uart4grp-1 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> +                       MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> +               >;
> +       };
> +
> +       pinctrl_usbhub: usbhubgrp {
> +               fsl,pins = <
> +                       MX6QDL_PAD_GPIO_6__GPIO1_IO06  0x1f059  /* HUB USB Reset */
> +               >;
> +       };
> +
> +       pinctrl_usbotg_2: usbotggrp-2 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> +               >;
> +       };
> +
> +       pinctrl_usdhc1_1: usdhc1grp-1 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
> +                       MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
> +                       MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> +                       MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> +                       MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> +                       MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> +               >;
> +       };
> +
> +       pinctrl_usdhc3_2: usdhc3grp-2 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17070
> +                       MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10070
> +                       MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070
> +                       MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
> +                       MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
> +                       MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
> +                       MX6QDL_PAD_GPIO_1__GPIO1_IO01  0x1f059  /* CD */
> +                       MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x1f059  /* PWR */
> +               >;
> +       };
> +
> +       pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170B1
> +                       MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100B1
> +                       MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
> +                       MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
> +                       MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
> +                       MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
> +               >;
> +       };
> +
> +       pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170F9
> +                       MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100F9
> +                       MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
> +                       MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
> +                       MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
> +                       MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
> +               >;
> +       };
> +
> +       pinctrl_usdhc4_1: usdhc4grp-1 {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17070
> +                       MX6QDL_PAD_SD4_CLK__SD4_CLK    0x10070
> +                       MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
> +                       MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
> +                       MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
> +                       MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
> +                       MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
> +                       MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
> +                       MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
> +                       MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
> +               >;
> +       };
> +
> +       pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170B1
> +                       MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100B1
> +                       MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1
> +                       MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1
> +                       MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1
> +                       MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1
> +                       MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1
> +                       MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1
> +                       MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1
> +                       MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1
> +               >;
> +       };
> +
> +       pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz {
> +               fsl,pins = <
> +                       MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170F9
> +                       MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100F9
> +                       MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9
> +                       MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9
> +                       MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9
> +                       MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9
> +                       MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9
> +                       MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9
> +                       MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9
> +                       MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
> +               >;
> +       };
> +};
> --
> 2.6.4
>
>  arch/arm/boot/dts/Makefile               |   1 +
>  arch/arm/boot/dts/imx6q-icore-rqs.dts    |  78 ++++++
>  arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 410 +++++++++++++++++++++++++++++++
>  3 files changed, 489 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6q-icore-rqs.dts
>  create mode 100644 arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bb8fa02..7e8f29c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -312,6 +312,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>   imx6q-gw551x.dtb \
>   imx6q-gw552x.dtb \
>   imx6q-hummingboard.dtb \
> + imx6q-icore-rqs.dtb \
>   imx6q-nitrogen6x.dtb \
>   imx6q-phytec-pbab01.dtb \
>   imx6q-rex-pro.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> new file mode 100644
> index 0000000..0053188
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-icore-rqs.dts
> @@ -0,0 +1,78 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +#include "imx6qdl-icore-rqs.dtsi"
> +
> +/ {
> + model = "Engicam i.CoreM6 Quad SOM";
> + compatible = "engicam,imx6-icore-rqs", "fsl,imx6q";
> +
> + sound {
> + compatible = "fsl,imx-audio-sgtl5000";
> + model = "imx-audio-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&codec>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&i2c3 {
> + codec: sgtl5000@0a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&clks IMX6QDL_CLK_CKO>;
> + VDDA-supply = <&reg_2p5v>;
> + VDDIO-supply = <&reg_3p3v>;
> + VDDD-supply = <&reg_1p8v>;
> + };
> +};
> +
> +&sata {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> new file mode 100644
> index 0000000..b984128
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
> @@ -0,0 +1,410 @@
> +/*
> + * Copyright (C) 2015 Amarula Solutions B.V.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License
> + *     version 2 as published by the Free Software Foundation.
> + *
> + *     This file is distributed in the hope that it will be useful
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/clock/imx6qdl-clock.h>
> +
> +/ {
> + memory {
> + reg = <0x10000000 0x80000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_2p5v: regulator-2p5v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P5V";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: regulator-3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_sd3_vmmc: sd3-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD3_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + enable-active-high;
> + };
> +
> + reg_sd4_vmmc: sd4-vmmc {
> + compatible = "regulator-fixed";
> + regulator-name = "P3V3_SD4_SWITCHED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_h1_vbus: usb-h1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_h1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: usb-otg-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + usb_hub: usb-hub {
> + compatible = "smsc,usb3503a";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbhub>;
> + reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + clocks = <&clks IMX6QDL_CLK_LVDS2_GATE>;
> + clock-names = "refclk";
> + };
> +};
> +
> +&clks {
> + assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
> + assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet_3>;
> + phy-handle = <&eth_phy>;
> + phy-mode = "rgmii";
> + status = "okay";
> + mdio {
> + eth_phy: ethernet-phy {
> + rxc-skew-ps = <1140>;
> + txc-skew-ps = <1140>;
> + txen-skew-ps = <600>;
> + rxdv-skew-ps = <240>;
> + rxd0-skew-ps = <420>;
> + rxd1-skew-ps = <600>;
> + rxd2-skew-ps = <420>;
> + rxd3-skew-ps = <240>;
> + txd0-skew-ps = <60>;
> + txd1-skew-ps = <60>;
> + txd2-skew-ps = <60>;
> + txd3-skew-ps = <240>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1_1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2_2>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3_4>;
> + status = "okay";
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4_1>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <&reg_usb_h1_vbus>;
> + disable-over-current;
> + clocks = <&clks IMX6QDL_CLK_USBOH3>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <&reg_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_2>;
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1_1>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3_2>;
> + pinctrl-1 = <&pinctrl_usdhc3_2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_2_200mhz>;
> + vmcc-supply = <&reg_sd3_vmmc>;
> + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> + bus-witdh=<4>;
> + no-1-8-v;
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc4_1>;
> + pinctrl-1 = <&pinctrl_usdhc4_1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc4_1_200mhz>;
> + vmcc-supply = <&reg_sd4_vmmc>;
> + bus-witdh=<8>;
> + no-1-8-v;
> + non-removable;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_audmux: audmux {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC  0x130b0
> + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD  0x110b0
> + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD  0x130b0
> + >;
> + };
> +
> + pinctrl_enet_3: enetgrp-3 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN     0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c1_1: i2c1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2_2: i2c2grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c3_4: i2c3grp-4 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x130b0
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1f059 /* PCIe Reset */
> + >;
> + };
> +
> + pinctrl_uart4_1: uart4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbhub: usbhubgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06  0x1f059 /* HUB USB Reset */
> + >;
> + };
> +
> + pinctrl_usbotg_2: usbotggrp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc1_1: usdhc1grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
> + MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> + >;
> + };
> +
> + pinctrl_usdhc3_2: usdhc3grp-2 {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17070
> + MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10070
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17070
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17070
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17070
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
> + MX6QDL_PAD_GPIO_1__GPIO1_IO01  0x1f059 /* CD */
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x1f059 /* PWR */
> + >;
> + };
> +
> + pinctrl_usdhc3_2_100mhz: usdhc3grp-2_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170B1
> + MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100B1
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170B1
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170B1
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170B1
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc3_2_200mhz: usdhc3grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170F9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100F9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170F9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170F9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170F9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170F9
> + >;
> + };
> +
> + pinctrl_usdhc4_1: usdhc4grp-1 {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17070
> + MX6QDL_PAD_SD4_CLK__SD4_CLK    0x10070
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
> + >;
> + };
> +
> + pinctrl_usdhc4_1_100mhz: usdhc4grp-1_100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170B1
> + MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100B1
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170B1
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170B1
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170B1
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170B1
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170B1
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170B1
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170B1
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170B1
> + >;
> + };
> +
> + pinctrl_usdhc4_1_200mhz: usdhc4grp-2_200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170F9
> + MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100F9
> + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x170F9
> + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x170F9
> + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x170F9
> + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x170F9
> + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x170F9
> + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x170F9
> + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x170F9
> + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x170F9
> + >;
> + };
> +};
> --
> 2.6.4
>
> --
> | Michael Nazzareno Trimarchi                     Amarula Solutions BV |
> | COO  -  Founder                                      Cruquiuskade 47 |
> | +31(0)851119172                                 Amsterdam 1018 AM NL |
> |                  [`as] http://www.amarulasolutions.com               |



-- 
| Michael Nazzareno Trimarchi                     Amarula Solutions BV |
| COO  -  Founder                                      Cruquiuskade 47 |
| +31(0)851119172                                 Amsterdam 1018 AM NL |
|                  [`as] http://www.amarulasolutions.com               |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux