Hi Jingoo, Thanks for your respond. On 12/22/2015 08:09 PM, Jingoo Han wrote:
On Wednesday, December 16, 2015 12:28 PM, Yakir Yang wrote:link_rate and lane_count already configured in analogix_dp_set_link_train(), so we don't need to config those repeatly after training finished, just remove them out. Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}. Signed-off-by: Yakir Yang <ykk@xxxxxxxxxxxxxx> Tested-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx> --- Changes in v11: None Changes in v10: None Changes in v9: None Changes in v8: None Changes in v7: None Changes in v6: None Changes in v5: None Changes in v4: - Update commit message more readable. (Jingoo) - Adjust the order from 05 to 04 Changes in v3: - The link_rate and lane_count shouldn't config to the DT property value directly, but we can take those as hardware limite. For example, RK3288 only support 4 physical lanes of 2.7/1.62 Gbps/lane, so DT property would like "link-rate = 0x0a" "lane-count = 4". (Thierry) Changes in v2: None drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 8 ++++---- drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 5 +++-- 2 files changed, 7 insertions(+), 6 deletions(-) diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c index 4a05c2b..6f899cd 100644 --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c @@ -624,6 +624,8 @@ static void analogix_dp_get_max_rx_bandwidth(struct analogix_dp_device *dp, /* * For DP rev.1.1, Maximum link rate of Main Link lanes * 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps + * For DP rev.1.2, Maximum link rate of Main Link lanes + * 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps, 0x14 = 5.4Gbps */ analogix_dp_read_byte_from_dpcd(dp, DP_MAX_LINK_RATE, &data); *bandwidth = data; @@ -657,7 +659,8 @@ static void analogix_dp_init_training(struct analogix_dp_device *dp, analogix_dp_get_max_rx_lane_count(dp, &dp->link_train.lane_count); if ((dp->link_train.link_rate != LINK_RATE_1_62GBPS) && - (dp->link_train.link_rate != LINK_RATE_2_70GBPS)) { + (dp->link_train.link_rate != LINK_RATE_2_70GBPS) && + (dp->link_train.link_rate != LINK_RATE_5_40GBPS)) { dev_err(dp->dev, "Rx Max Link Rate is abnormal :%x !\n", dp->link_train.link_rate); dp->link_train.link_rate = LINK_RATE_1_62GBPS; @@ -898,9 +901,6 @@ static void analogix_dp_commit(struct analogix_dp_device *dp) analogix_dp_enable_rx_to_enhanced_mode(dp, 1); analogix_dp_enable_enhanced_mode(dp, 1); - analogix_dp_set_lane_count(dp, dp->video_info->lane_count); - analogix_dp_set_link_bandwidth(dp, dp->video_info->link_rate); - analogix_dp_init_video(dp); ret = analogix_dp_config_video(dp); if (ret) diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h index 8e84208..57aa4b0d 100644 --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h @@ -21,8 +21,9 @@ #define MAX_EQ_LOOP 5 enum link_rate_type { - LINK_RATE_1_62GBPS = 0x06, - LINK_RATE_2_70GBPS = 0x0a + LINK_RATE_1_62GBPS = DP_LINK_BW_1_62, + LINK_RATE_2_70GBPS = DP_LINK_BW_2_7, + LINK_RATE_5_40GBPS = DP_LINK_BW_5_4,Then, how about removing 'enum link_rate_type'? If DP_LINK_BW_* are used, LINK_RATE_* are not necessary.
Sure, good catch. Thanks, - Yakir
Best regards, Jingoo Han}; enum link_lane_count_type { -- 1.9.1
-- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
