On 12/18/2015 09:14 PM, Rob Herring wrote:
> On Mon, Dec 14, 2015 at 03:42:05PM -0700, Joshua Henderson wrote:
>> From: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>
>>
>> Document the devicetree bindings for the clock driver found on Microchip
>> PIC32 class devices.
>>
>> Signed-off-by: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>
>> Signed-off-by: Joshua Henderson <joshua.henderson@xxxxxxxxxxxxx>
>> Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>
> A couple of nits on the example, otherwise:
>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
>
>> ---
>> .../devicetree/bindings/clock/microchip,pic32.txt | 256 ++++++++++++++++++++
>> 1 file changed, 256 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/clock/microchip,pic32.txt
>>
>> diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
>> new file mode 100644
>> index 0000000..f50c653
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
>> @@ -0,0 +1,256 @@
>> +Binding for a Clock hardware block found on
>> +certain Microchip PIC32 MCU devices.
>> +
>> +Microchip SoC clocks-node consists of few oscillators, PLL, multiplexer
>> +and few divider nodes.
>> +
>> +We will find only the base address of the clock tree, this base
>> +address is common for some of the subnodes, not all. If no address is
>> +specified for any of subnode base address of the clock tree will be
>> +treated as its base. Each of subnodes follow the same common clock
>> +binding with some additional optional properties.
>> +
>> + clocks_node {
>> + reg = <>;
>> +
>> + spll_node {
>> + ...
>> + };
>> +
>> + frcdiv_node {
>> + ...
>> + };
>> +
>> + sysclk_mux_node {
>> + ...
>> + };
>> +
>> + pbdiv_node {
>> + ...
>> + };
>> +
>> + refoclk_node {
>> + ...
>> + };
>> + ...
>> + };
>> +
>> +This binding uses the common clock binding[1].
>> +
>> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>> +
>> +Required properties:
>> +- compatible : should be one of "microchip,pic32mzda-clk",
>> + "microchip,pic32mzda-sosc", "microchip,pic32mzda-frcdivclk",
>> + "microchip,pic32mzda-syspll", "microchip,pic32mzda-sysclk-v2",
>> + "microchip,pic32mzda-pbclk", "microchip,pic32mzda-refoclk".
>> +- reg : A Base address and length of the register set.
>> +- interrupts : source of interrupt.
>> +
>> +Optional properties (for subnodes):
>> +- #clock-cells: From common clock binding, should be 0.
>> +- microchip,clock-indices: in multiplexer node clock sources always aren't linear
>> + and contiguous. This property helps define clock-sources with respect to
>> + the mux clock node.
>> +- microchip,ignore-unused : ignore gate request even if the gated clock is unused.
>> +- microchip,status-bit-mask: bitmask for status check. This will be used to confirm
>> + particular operation by clock sub-node is completed. It is dependent sub-node.
>> +- microchip,bit-mask: enable mask, similar to microchip,status-bit-mask.
>> +- microchip,slew-step: enable frequency slewing(stepping) during rate change;
>> + applicable only to sys-clock subnode.
>> +
>> +Example:
>> +
>> +/* PIC32 specific clks */
>> +pic32_clktree {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + reg = <0x1f801200 0x200>;
>> + compatible = "microchip,pic32mzda-clk";
>> + ranges = <0 0x1f801200 0x200>;
>> +
>> + /* secondary oscillator; external input on SOSCI pin */
>> + SOSC:sosc_clk {
> For the ones with reg property, do clock@0 instead of sosc_clk.
ack. Will update.
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-sosc";
>> + clock-frequency = <32768>;
>> + reg = <0x000 0x10>, /* enable reg */
>> + <0x1d0 0x10>; /* status reg */
>> + microchip,bit-mask = <0x02>; /* enable mask */
>> + microchip,status-bit-mask = <0x10>; /* status-mask*/
>> + };
>> +
>> + FRCDIV:frcdiv_clk {
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-frcdivclk";
>> + clocks = <&FRC>;
>> + clock-output-names = "frcdiv_clk";
>> + };
>> +
>> + /* System PLL clock */
>> + SYSPLL:spll_clk {
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-syspll";
>> + reg = <0x020 0x10>, /* SPLL register */
>> + <0x1d0 0x10>; /* CLKSTAT register */
>> + clocks = <&POSC>, <&FRC>;
>> + clock-output-names = "sys_pll";
>> + microchip,status-bit-mask = <0x80>; /* SPLLRDY */
>> + };
>> +
>> + /* system clock; mux with postdiv & slew */
>> + SYSCLK:sys_clk {
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-sysclk-v2";
>> + reg = <0x1c0 0x04>; /* SLEWCON */
>> + clocks = <&FRCDIV>, <&SYSPLL>, <&POSC>, <&SOSC>,
>> + <&LPRC>, <&FRCDIV>;
>> + microchip,clock-indices = <0>, <1>, <2>, <4>, <5>, <7>;
>> + clock-output-names = "sys_clk";
>> + };
>> +
>> + /* UPLL is integral part of USB PHY; UTMI clk for USBCORE */
>> + UPLL:usb_phy_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clocks";
>> + clock-frequency = <24000000>;
>> + clock-output-names = "usbphy_clk";
>> + };
>> +
>> + /* Peripheral bus1 clock */
>> + PBCLK1:pb1_clk {
>> + reg = <0x140 0x10>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + clock-output-names = "pb1_clk";
>> + /* used by system modules, not gateable */
>> + microchip,ignore-unused;
>> + };
>> +
>> + /* Peripheral bus2 clock */
>> + PBCLK2:pb2_clk {
>> + reg = <0x150 0x10>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + clock-output-names = "pb2_clk";
>> + /* avoid gating even if unused */
>> + microchip,ignore-unused;
>> + };
>> +
>> + /* Peripheral bus3 clock */
>> + PBCLK3:pb3_clk {
>> + reg = <0x160 0x10>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + clock-output-names = "pb3_clk";
>> + };
>> +
>> + /* Peripheral bus4 clock(I/O ports, GPIO) */
>> + PBCLK4:pb4_clk {
>> + reg = <0x170 0x10>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + clock-output-names = "pb4_clk";
>> + };
>> +
>> + /* Peripheral bus clock */
>> + PBCLK5:pb5_clk {
>> + reg = <0x180 0x10>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + clock-output-names = "pb5_clk";
>> + };
>> +
>> + /* Peripheral Bus6 clock; */
>> + PBCLK6:pb6_clk {
>> + reg = <0x190 0x10>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + clocks = <&SYSCLK>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + /* Peripheral bus7 clock */
>> + PBCLK7:pb7_clk {
>> + reg = <0x1A0 0x10>;
> lower case
ack.
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-pbclk";
>> + /* CPU is driven by this clock; so named */
>> + clock-output-names = "cpu_clk";
>> + clocks = <&SYSCLK>;
>> + };
>> +
>> + /* Reference Oscillator clock for SPI/I2S */
>> + REFCLKO1:refo1_clk {
>> + reg = <0x080 0x20>;
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-refoclk";
>> + clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
>> + <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
>> + microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
>> + <7>, <8>, <9>;
>> + clock-output-names = "refo1_clk";
>> + };
>> +
>> + /* Reference Oscillator clock for SQI */
>> + REFCLKO2:refo2_clk {
>> + reg = <0x0A0 0x20>;
> lower case
ack.
>> + #clock-cells = <0>;
>> + compatible = "microchip,pic32mzda-refoclk";
>> + clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
>> + <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
>> + microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
>> + <7>, <8>, <9>;
>> + clock-output-names = "refo2_clk";
>> + };
>> +
>> + /* Reference Oscillator clock, ADC */
>> + REFCLKO3:refo3_clk {
>> + reg = <0x0C0 0x20>;
> lower case
ack.
>> + compatible = "microchip,pic32mzda-refoclk";
>> + clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
>> + <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
>> + microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
>> + <7>, <8>, <9>;
>> + #clock-cells = <0>;
>> + clock-output-names = "refo3_clk";
>> + };
>> +
>> + /* Reference Oscillator clock */
>> + REFCLKO4:refo4_clk {
>> + reg = <0x0E0 0x20>;
>> + compatible = "microchip,pic32mzda-refoclk";
>> + clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
>> + <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
>> + microchip,clock-indices = <0>,<1>,<2>,<3>,<4>,<5>,<7>,
>> + <8>,<9>;
>> + #clock-cells = <0>;
>> + clock-output-names = "refo4_clk";
>> + };
>> +
>> + /* Reference Oscillator clock, LCD */
>> + REFCLKO5:refo5_clk {
>> + reg = <0x100 0x20>;
>> + compatible = "microchip,pic32mzda-refoclk";
>> + clocks = <&SYSCLK>,<&PBCLK1>,<&POSC>,<&FRC>,<&LPRC>,
>> + <&SOSC>,<&SYSPLL>,<&REFIx>,<&BFRC>;
>> + microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
>> + <7>, <8>,<9>;
>> + #clock-cells = <0>;
>> + clock-output-names = "refo5_clk";
>> + };
>> +};
>> +
>> +The clock consumer should specify the desired clock by having the clocks in its
>> +"clock" phandle cell. For example for UART:
>> +
>> +uart2: serial@<> {
>> + compatible = "microchip,pic32mzda-uart";
>> + reg = <>;
>> + interrupts = <>;
>> + clocks = <&PBCLK2>;
>> +}
>> --
>> 1.7.9.5
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
