Re: [PATCH v5] arm: pxa: support ICP DAS LP-8x4x FPGA irq

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Fri, 2015-12-18 at 21:58 -0600, Rob Herring wrote:
> On Tue, Dec 15, 2015 at 10:26:21PM +0300, Sergei Ianovich wrote:
> > +Example:
> > +
> > +	fpga: fpga@17000006 {
> 
> Nothing else in the fpga? In any case, this node should be named 
> interrupt-controller@17000006.
> 
> > +		compatible = "icpdas,irq-lp8x4x";
> 
> As pointed out in the uart binding, don't use wildcards here.
> 
> > +		reg = <0x17000006 0x16>;
> > +		interrupt-parent = <&gpio>;
> > +		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
> > +		#interrupt-cells = <1>;
> > +		interrupt-controller;
> > +		status = "okay";
> > +	};
> > +
> > +	uart@17009050 {
> > +		compatible = "icpdas,uart-lp8x4x";
> > +		reg = <0x17009050 0x10
> > +		       0x17009030 0x02>;
> > +		interrupt-parent = <&fpga>;
> > +		interrupts = <13>;
> > +		status = "okay";
> > +	};

That was just an example. The actual binding in LP-8x4x is bigger:
                fpga@5 {
                        compatible = "simple-bus";
                        #address-cells = <1>;
                        #size-cells = <1>;
                        ranges = <0 5 0x3000000 0x10000>;
                        interrupt-parent = <&fpgairq>;

                        rtc@901c {
                                compatible = "dallas,rtc-ds1302";
                                reg = <0x901c 0x1>;
                                status = "okay";
                        };

                        sram@a000 {
                                compatible = "icpdas,sram-lp8x4x";
                                reg = <0xa000 0x1000
                                       0x901e 0x1>;

                                partitions {
                                        #address-cells = <1>;
                                        #size-cells = <1>;
                                };
                        };

                        fpgairq: irq@9006 {
                                compatible = "icpdas,irq-lp8x4x";
                                reg = <0x9006 0x16>;
                                interrupt-parent = <&gpio>;
                                interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
                                #interrupt-cells = <1>;
                                interrupt-controller;
                                status = "okay";
                        };

                        uart@9050 {
                                compatible = "icpdas,uart-lp8x4x";
                                reg = <0x9050 0x10
                                       0x9030 0x02>;
                                interrupts = <13>;
                                status = "okay";
                        };

                        uart@9060 {
                                compatible = "icpdas,uart-lp8x4x";
                                reg = <0x9060 0x10
                                       0x9032 0x02>;
                                interrupts = <14>;
                                status = "okay";
                        };

                        uart@9070 {
                                compatible = "icpdas,uart-lp8x4x";
                                reg = <0x9070 0x10
                                       0x9034 0x02>;
                                interrupts = <15>;
                                status = "okay";
                        };

                        backplane {
                                compatible = "icpdas,backplane-lp8x4x";
                                reg = <0x0 0x2
                                       0x1000 0x10
                                       0x2000 0x10
                                       0x3000 0x10
                                       0x4000 0x10
                                       0x5000 0x10
                                       0x6000 0x10
                                       0x7000 0x10
                                       0x8000 0x10
                                       0x9002 0x2
                                       0x9004 0x2
                                       0x9046 0x2>;
                                eeprom-gpios = <&gpio 4 0>;
                        };
                };
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux