On Tue, Dec 15, 2015 at 09:32:18AM -0200, Fabio Estevam wrote: > On Tue, Dec 15, 2015 at 4:28 AM, Peter Chen <peter.chen@xxxxxxxxxxxxx> wrote: > > > Thanks, Fabio. > > > > I am afraid I forget to set gpio as output, would you please apply > > below patch against my original ones: > > Same error happens with these changes applied. > > Here are more details: if I run a pure 4.3.2 then I do see the USB > stick to get detected if I boot it with the USB stick connected to > Udoo board: > > [ 2.170178] usb 1-1.1: new high-speed USB device number 3 using ci_hdrc > [ 2.305840] usb-storage 1-1.1:1.0: USB Mass Storage device detected > [ 2.314803] scsi host1: usb-storage 1-1.1:1.0 > [ 2.400283] usb 1-1.3: new high-speed USB device number 4 using ci_hdrc > [ 3.327925] scsi 1:0:0:0: Direct-Access General USB Flash Disk 1.0 P2 > [ 3.347070] sd 1:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73) > [ 3.356181] sd 1:0:0:0: [sda] Write Protect is off > [ 3.362550] sd 1:0:0:0: [sda] No Caching mode page found > [ 3.367899] sd 1:0:0:0: [sda] Assuming drive cache: write through > [ 3.387401] sda: sda1 > [ 3.400238] sd 1:0:0:0: [sda] Attached SCSI removable disk > [ 4.931847] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow contx > [ 4.941414] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 4.961400] Sending DHCP requests ., OK > [ 5.380247] IP-Config: Got DHCP answer from 10.29.244.251, my address is 10.1 > [ 5.390461] IP-Config: Complete: > [ 5.393731] device=eth0, hwaddr=00:c0:08:88:0c:b5, ipaddr=10.29.244.61,4 > [ 5.404074] host=10.29.244.61, domain=am.freescale.net, nis-domain=(non) > [ 5.411362] bootserver=0.0.0.0, rootserver=10.29.244.24, rootpath= 0 > [ 5.423964] ALSA device list: > [ 5.426969] No soundcards found. > [ 5.469374] VFS: Mounted root (nfs filesystem) readonly on device 0:14. > [ 5.478119] devtmpfs: mounted > [ 5.482376] Freeing unused kernel memory: 456K (c0a7e000 - c0af0000) > starting pid 160, tty '': '/etc/rc.d/rcS' > Mounting /proc and /sys > Starting the hotplug events dispatcher udevd > Synthesizing initial hotplug even[ 6.085842] udevd (173): /proc/173/oom_adj . > > ,but the system hangs here. > > If I boot it with the USB stick disconnected, then the system boots > until the prompt, but the insertion of the USB stick is never detected > afterwards. > Thanks, Fabio, but I am curious how things like that? The USBOH3 clock is not opened, the usb driver will hang when it tries to access registers. If this clock is always on, then, why the system will hang later? > With your patch applied, the error message (usb 1-1: device descriptor > read/64, error -7) is shown with USB stick connected or disconnected > during boot. Would you help to check again the clock is IMX6QDL_CLK_CKO and the reset pin is GPIO7 bit 12? If they are, check below two things please: - The clock is opened (You can check if through clock tree) - The gpio is high (phy_addr is 0x20b4000, the bit is 12) If they are correct, try to toggle gpio manually to see if it can work. -- Best Regards, Peter Chen -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
