Re: [PATCH V4 12/16] Documentation: DT: bindings: Add power domain info for NVIDIA PMC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Jon Hunter <jonathanh@xxxxxxxxxx> writes:

> On 08/12/15 19:07, Kevin Hilman wrote:
>> Jon Hunter <jonathanh@xxxxxxxxxx> writes:
>> 
>>> Add power-domain binding documentation for the NVIDIA PMC driver in
>>> order to support generic power-domains.
>>>
>>> Signed-off-by: Jon Hunter <jonathanh@xxxxxxxxxx>
>>>
>>> ---
>>>
>>> Please note that I have been debating whether I add this
>>> "nvidia,powergate-clock-disable" property or just leave the clocks
>>> disabled by default. Some downstream kernels leave the clocks enabled
>>> for the audio power-domain because the clocks required for powering up
>>> the power-domain are needed by all modules within the power-domain.
>>> However are the same time there are other power-domains that may need
>>> to be on, but not always clocked and so having the ability to specify if
>>> the clocks should be disabled seems useful. However, I can also remove
>>> this and just have the appropriate devices turn on the clocks as well.
>>> ---
>>>  .../bindings/arm/tegra/nvidia,tegra20-pmc.txt      | 61 ++++++++++++++++++++++
>>>  1 file changed, 61 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>>> index 838e1a69ec0a..8e4641db51a9 100644
>>> --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>>> +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>>> @@ -1,5 +1,7 @@
>>>  NVIDIA Tegra Power Management Controller (PMC)
>>>  
>>> +== Power Management Controller Node ==
>>> +
>>>  The PMC block interacts with an external Power Management Unit. The PMC
>>>  mostly controls the entry and exit of the system from different sleep
>>>  modes. It provides power-gating controllers for SoC and CPU power-islands.
>>> @@ -69,6 +71,10 @@ Optional properties for hardware-triggered thermal reset (inside 'i2c-thermtrip'
>>>                       Defaults to 0. Valid values are described in section 12.5.2
>>>                       "Pinmux Support" of the Tegra4 Technical Reference Manual.
>>>  
>>> +Optional nodes:
>>> +- pm-domains : This node contains a hierarchy of PM domain nodes, which should
>>> +	       match the power-domains on the Tegra SoC.
>>> +
>>>  Example:
>>>  
>>>  / SoC dts including file
>>> @@ -114,3 +120,58 @@ pmc@7000f400 {
>>>  	};
>>>  	...
>>>  };
>>> +
>>> +
>>> +== PM Domain Nodes ==
>>> +
>>> +Each of the PM domain nodes represents a power-domain on the Tegra SoC
>>> +that can be power-gated by the PMC and should be named appropriately.
>>> +
>>> +Required properties:
>>> +  - clocks: Must contain an entry for each clock required by the PMC for
>>> +    controlling a power-gate. See ../clocks/clock-bindings.txt for details.
>> 
>> We've had this discussiona for a couple of other SoCs, so I need to
>> ask...
>> 
>> Presumably these are not device clocks that a runtime PM enabled driver
>> should be managing for a device, right?  IOW, We want to make sure that the
>> PM domain isn't managing clocks for drivers that should be doing it.
>> 
>> I understand there are legitimate reasons for the PM domain to manage
>> clocks in addition to device drivers (e.g. for synchronous reset), but
>> just want to be sure it's not a shortcut for having a proper driver.
>
> So some clocks may also be used by devices, but they are needed as part
> of the power ungating/gating sequence. The general power-up sequence for
> tegra is ...
>
> 1. Enable the power-domain
> 2. Enable the clock(s)
> 3. Remove signal clamps
> 4. De-assert reset(s)
> 5. Disable clocks (optional)
>
> You may say we should only handle #1 above for the powering up sequence,
> but we can't do this. The reason is that there is one bit for each
> power-domain that controls the signaling clamps and so we need to turn
> on all the clocks specified in the TRM before we do this. Once we have
> done this and released the reset(s), we can then disable the clocks
> again (shown above an optional as it is not mandatory from a design
> perspective) and then the devices in the power-domain should enable the
> clocks they need as and when they want them.

Thanks for the clarification, that's what I expected and similar to what
I've seen on other SoCs.  I just wanted to be sure that the power-domain
clk managent was "in addition" to the device drivers, not "instead of."

Kevin
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux