On Mon, Dec 07, 2015 at 02:48:04PM +0100, linux-kernel-dev@xxxxxxxxxxxx wrote: > From: Patrick Brünn <p.bruenn@xxxxxxxxxxxx> > > On Tue, Dec 1, 2015 at 20:52:25 PST, shawnguo@xxxxxxxxxx wrote: > > On Thu, Nov 26, 2015 at 11:59:15AM +0100, linux-kernel-dev@xxxxxxxxxxxx wrote: > >> MX53_PAD_EIM_D27__UART2_RXD_MUX and MX53_PAD_EIM_D29__UART2_RTS input_val must be configured as 0 instead of 1 to have UART2 muxed on EIM pins working > > > > I'm not sure why you think that. But the i.MX53 Reference Manual in my hands doesn't agree with that. It says ... > >> > >> Signed-off-by: Patrick Brünn <p.bruenn@xxxxxxxxxxxx> > >> --- > >> arch/arm/boot/dts/imx53-pinfunc.h | 4 ++-- > >> 1 file changed, 2 insertions(+), 2 deletions(-) > >> > >> diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h > >> index aec406b..a4c973d 100644 > >> --- a/arch/arm/boot/dts/imx53-pinfunc.h > >> +++ b/arch/arm/boot/dts/imx53-pinfunc.h > >> @@ -532,7 +532,7 @@ > >> #define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0 > >> #define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0 > >> #define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0 > >> -#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1 > >> +#define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x0 > > > > IOMUXC_UART2_IPP_UART_RXD_MUX_SELECT_INPUT DAISY field descriptions > > > > 000 - Selecting Pad: EIM_D26 for Mode: ALT2. > > 001 - Selecting Pad: EIM_D27 for Mode: ALT2. > > 010 - Selecting Pad: PATA_DMARQ for Mode: ALT3. > > 011 - Selecting Pad: PATA_BUFFER_EN for Mode: ALT3. > > 100 - Selecting Pad: GPIO_7 for Mode: ALT4. > > 101 - Selecting Pad: GPIO_8 for Mode: ALT4. > > > Thanks for the hint. I had a closer look at the reference manual and our schematics. Of course, you are right. The defines are good as they are, my patch was stupid. > > I just realized RXD and TXD are inverted on our hardware (CX9020 Embedded PC). Which requires a pinmux configuration like this: > EIM_D26->UART2_RXD > EIM_D27->UART2_TXD > EIM_D28->UART2_RTS > EIM_D29->UART2_CTS > > In my opinion the reference manual allows such a configuration, but I am not sure if it's appropriate for mainline. > > Would you accept a patch like the following: No, I'm not going to accept it. But it doesn't mean you cannot define and use it in your own board DTS file. Shawn > > >8------------------------------------------------------8< > ARM: dts: imx53: add EIM pad config for UART2 > > Add another pinmux configuration to mux UART2 on EIM pads: > > EIM_D26->UART2_RXD > EIM_D27->UART2_TXD > EIM_D28->UART2_RTS > EIM_D29->UART2_CTS > > Signed-off-by: Patrick Brünn <p.bruenn@xxxxxxxxxxxx> > --- > arch/arm/boot/dts/imx53-pinfunc.h | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/imx53-pinfunc.h > index aec406b..7d26d16 100644 > --- a/arch/arm/boot/dts/imx53-pinfunc.h > +++ b/arch/arm/boot/dts/imx53-pinfunc.h > @@ -525,6 +525,7 @@ > #define MX53_PAD_EIM_D26__EMI_WEIM_D_26 0x144 0x48c 0x000 0x0 0x0 > #define MX53_PAD_EIM_D26__GPIO3_26 0x144 0x48c 0x000 0x1 0x0 > #define MX53_PAD_EIM_D26__UART2_TXD_MUX 0x144 0x48c 0x000 0x2 0x0 > +#define MX53_PAD_EIM_D26__UART2_RXD_MUX 0x144 0x48c 0x880 0x2 0x0 > #define MX53_PAD_EIM_D26__FIRI_RXD 0x144 0x48c 0x80c 0x3 0x0 > #define MX53_PAD_EIM_D26__IPU_CSI0_D_1 0x144 0x48c 0x000 0x4 0x0 > #define MX53_PAD_EIM_D26__IPU_DI1_PIN11 0x144 0x48c 0x000 0x5 0x0 > @@ -532,6 +533,7 @@ > #define MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x144 0x48c 0x000 0x7 0x0 > #define MX53_PAD_EIM_D27__EMI_WEIM_D_27 0x148 0x490 0x000 0x0 0x0 > #define MX53_PAD_EIM_D27__GPIO3_27 0x148 0x490 0x000 0x1 0x0 > +#define MX53_PAD_EIM_D27__UART2_TXD_MUX 0x148 0x490 0x000 0x2 0x0 > #define MX53_PAD_EIM_D27__UART2_RXD_MUX 0x148 0x490 0x880 0x2 0x1 > #define MX53_PAD_EIM_D27__FIRI_TXD 0x148 0x490 0x000 0x3 0x0 > #define MX53_PAD_EIM_D27__IPU_CSI0_D_0 0x148 0x490 0x000 0x4 0x0 > @@ -541,6 +543,7 @@ > #define MX53_PAD_EIM_D28__EMI_WEIM_D_28 0x14c 0x494 0x000 0x0 0x0 > #define MX53_PAD_EIM_D28__GPIO3_28 0x14c 0x494 0x000 0x1 0x0 > #define MX53_PAD_EIM_D28__UART2_CTS 0x14c 0x494 0x000 0x2 0x0 > +#define MX53_PAD_EIM_D28__UART2_RTS 0x14c 0x494 0x87c 0x2 0x0 > #define MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO 0x14c 0x494 0x82c 0x3 0x1 > #define MX53_PAD_EIM_D28__CSPI_MOSI 0x14c 0x494 0x788 0x4 0x1 > #define MX53_PAD_EIM_D28__I2C1_SDA 0x14c 0x494 0x818 0x5 0x1 > @@ -548,6 +551,7 @@ > #define MX53_PAD_EIM_D28__IPU_DI0_PIN13 0x14c 0x494 0x000 0x7 0x0 > #define MX53_PAD_EIM_D29__EMI_WEIM_D_29 0x150 0x498 0x000 0x0 0x0 > #define MX53_PAD_EIM_D29__GPIO3_29 0x150 0x498 0x000 0x1 0x0 > +#define MX53_PAD_EIM_D29__UART2_CTS 0x150 0x498 0x000 0x2 0x0 > #define MX53_PAD_EIM_D29__UART2_RTS 0x150 0x498 0x87c 0x2 0x1 > #define MX53_PAD_EIM_D29__IPU_DISPB0_SER_RS 0x150 0x498 0x000 0x3 0x0 > #define MX53_PAD_EIM_D29__CSPI_SS0 0x150 0x498 0x78c 0x4 0x2 > -- > 1.9.1 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
