On Fri, Dec 04, 2015 at 09:35:06AM +0100, Enric Balletbo i Serra wrote:
> The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> designed for portable devices.
>
> You can add support to your board with current binding.
>
> Example:
>
> anx7814: anx7814@38 {
> compatible = "analogix,anx7814";
> reg = <0x38>;
> interrupt-parent = <&gpio0>
> interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> pd-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> reset-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
> v10-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> ports {
This and the example below should be just "port" I think. Otherwise:
Acked-by: Rob Herring <robh@xxxxxxxxxx>
> anx7814_in: endpoint {
> remote-endpoint = <&hdmi0_out>;
> };
> };
> };
>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
> ---
>
> Changes since last version (requested by Rob Herring)
> - Specify how many ports and how many endpoints for each port
> - Simplify to just port (dropping ports)
> - For cable det use an interrupt instead (to a gpio controller)
>
> .../devicetree/bindings/video/bridge/anx7814.txt | 39 ++++++++++++++++++++++
> 1 file changed, 39 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/video/bridge/anx7814.txt
>
> diff --git a/Documentation/devicetree/bindings/video/bridge/anx7814.txt b/Documentation/devicetree/bindings/video/bridge/anx7814.txt
> new file mode 100644
> index 0000000..4e68789
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/video/bridge/anx7814.txt
> @@ -0,0 +1,39 @@
> +Analogix ANX7814 SlimPort (Full-HD Transmitter)
> +-----------------------------------------------
> +
> +The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
> +designed for portable devices.
> +
> +Required properties:
> +
> + - compatible : "analogix,anx7814"
> + - reg : I2C address of the device
> + - interrupt-parent : Should be the phandle of the interrupt controller
> + that services interrupts for this device
> + - interrupts : Should contain the cable detection interrupt
> + - pd-gpios : Which GPIO to use for power down
> + - reset-gpios : Which GPIO to use for reset
> +
> +Optional properties:
> +
> + - v10-gpios : Which GPIO to use for V10 control.
> + - Video port for HDMI output, using the DT bindings defined in [1].
> +
> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example:
> +
> + anx7814: anx7814@38 {
> + compatible = "analogix,anx7814";
> + reg = <0x38>;
> + interrupt-parent = <&gpio0>
> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> + pd-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
> + v10-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
> + ports {
> + anx7814_in: endpoint {
> + remote-endpoint = <&hdmi0_out>;
> + };
> + };
> + };
> --
> 2.1.0
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
