Hi Jassi,
thanks for your feedback.
On Mon, Aug 10, 2015 at 1:05 AM, Jassi Brar <jassisinghbrar@xxxxxxxxx> wrote:
> On Wed, Jul 15, 2015 at 6:30 AM, Moritz Fischer
> <moritz.fischer@xxxxxxxxx> wrote:
>
>> +
>> +static void xilinx_mbox_rx_data(struct mbox_chan *chan)
>> +{
>> + struct xilinx_mbox *mbox = mbox_chan_to_xilinx_mbox(chan);
>> + u32 data;
>> +
>> + if (xilinx_mbox_pending(mbox)) {
>> + data = readl_relaxed(mbox->mbox_base + MAILBOX_REG_RDDATA);
>> + mbox_chan_received_data(chan, (void *)data);
>>
> If RDDATA is a FIFO, then above seems wrong - you are assuming
> messages are always going to be exactly 32-bits for every protocol.
> Ideally you should empty the fifo fully, at least when RX has an
> interrupt.
>From my understanding it's hard to tell how much actually is in the fifo,
you can tell if it's full for send direction, or empty for read direction.
Maybe the STI / RTI can be setup in a smart way to work with multiple message
sizes.
>
>> +
>> +static int xilinx_mbox_irq_send_data(struct mbox_chan *chan, void *data)
>> +{
>> + struct xilinx_mbox *mbox = mbox_chan_to_xilinx_mbox(chan);
>> + u32 *udata = data;
>> +
>> + if (xilinx_mbox_full(mbox))
>> + return -EBUSY;
>>
> This check is redundant. last_tx_done already makes sure this is always true.
Good to know. I'll fix it.
>
>> + /* enable interrupt before send */
>> + xilinx_mbox_tx_intmask(mbox, true);
>> +
>> + writel_relaxed(*udata, mbox->mbox_base + MAILBOX_REG_WRDATA);
>> +
> From status EMPTY and FULL, it seems WRDATA is a FIFO. So here also
> you should expect messages to be <= fifo depth. And not assume exactly
> 32bit messages always.
How do I determine the message size? Doesn't
drivers/mailbox/bcm2835-mailbox.c or
mailbox-altera.c make the same assumption?
>
>> +
>> +static bool xilinx_mbox_last_tx_done(struct mbox_chan *chan)
>> +{
>> + struct xilinx_mbox *mbox = mbox_chan_to_xilinx_mbox(chan);
>> +
>> + /* return false if mailbox is full */
>> + return !xilinx_mbox_full(mbox);
>>
> Instead of FULL, I think it should check for stricter EMPTY status ...
> mbox api submits only 1 message at a time.
The EMPTY status applies to the receive direction only, I could check
the STI status
bit though I suppose.
[...]
>> +
>> + mbox->irq = platform_get_irq(pdev, 0);
>> + /* if irq is present, we can use it, otherwise, poll */
>> + if (mbox->irq > 0) {
>> + mbox->controller.txdone_irq = true;
>> + mbox->controller.ops = &xilinx_mbox_irq_ops;
>> + } else {
>> + dev_info(&pdev->dev, "IRQ not found, fallback to polling.\n");
>> + mbox->controller.txdone_poll = true;
>> + mbox->controller.txpoll_period = MBOX_POLLING_MS;
>> + mbox->controller.ops = &xilinx_mbox_poll_ops;
>> +
>> + setup_timer(&mbox->rxpoll_timer, xilinx_mbox_poll_rx,
>> + (unsigned long)&mbox->chan);
>>
> I believe there is indeed some platform that doesn't have RX-Interrupt?
> If no, please remove this.
> If yes, you may want to get some hint from platform about the size of
> messages and do mbox_chan_received_data() only upon reading those many
> bytes.
I'd be fine to drop the polling use case for the moment, on my
platform I can wire up the IRQ.
We can always add it back in in a follow up use case.
Thanks,
Moritz
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
