On Sat, Nov 28, 2015 at 06:38:57PM +0800, Xinliang Liu wrote:
> Add the device tree binding documentation for hi6220 SoC display subsystem.
> drm master device binding doc.
> ADE display controller binding doc.
> DSI controller binding doc.
>
> Signed-off-by: Xinliang Liu <xinliang.liu@xxxxxxxxxx>
> Signed-off-by: Xinwei Kong <kong.kongxinwei@xxxxxxxxxxxxx>
> Signed-off-by: Andy Green <andy.green@xxxxxxxxxx>
> ---
> .../bindings/display/hisilicon/hisi-ade.txt | 42 ++++++++++++++
> .../bindings/display/hisilicon/hisi-drm.txt | 66 ++++++++++++++++++++++
> .../bindings/display/hisilicon/hisi-dsi.txt | 53 +++++++++++++++++
> 3 files changed, 161 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-drm.txt
> create mode 100644 Documentation/devicetree/bindings/display/hisilicon/hisi-dsi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
> new file mode 100644
> index 0000000..2777a2c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt
> @@ -0,0 +1,42 @@
> +Device-Tree bindings for hisilicon ADE display controller driver
> +
> +ADE (Advanced Display Engine) is the display controller which grab image
> +data from memory, do composition, do post image processing, generate RGB
> +timing stream and transfer to DSI.
> +
> +Required properties:
> +- compatible: value should be one of the following
> + "hisilicon,hi6220-ade".
> +- reg: physical base address and length of the controller's registers.
> +- reg-names: name of physical base.
> +- interrupt: the interrupt number.
> +- clocks: the clocks needed.
> +- clock-names: the name of the clocks.
> +- ade_core_clk_rate: ADE core clock rate.
> +- media_noc_clk_rate: media noc module clock rate.
I think you can use assigned clock properties instead:
assigned-clocks = <&media_ctrl HI6220_ADE_CORE>;
assigned-clock-rates = <360000000>;
I'm not sure about what media_noc corresponds to in clocks list though.
> +
> +
> +A example of HiKey board hi6220 SoC specific DT entry:
> +Example:
> +
> + ade: ade@f4100000 {
> + compatible = "hisilicon,hi6220-ade";
> + reg = <0x0 0xf4100000 0x0 0x7800>,
> + <0x0 0xf4410000 0x0 0x1000>;
> + reg-names = "ade_base",
> + "media_base";
> + interrupts = <0 115 4>;
> +
> + clocks = <&media_ctrl HI6220_ADE_CORE>,
> + <&media_ctrl HI6220_CODEC_JPEG>,
> + <&media_ctrl HI6220_ADE_PIX_SRC>,
> + <&media_ctrl HI6220_PLL_SYS>,
> + <&media_ctrl HI6220_PLL_SYS_MEDIA>;
> + clock-names = "clk_ade_core",
> + "aclk_codec_jpeg_src",
> + "clk_ade_pix",
> + "clk_syspll_src",
> + "clk_medpll_src";
> + ade_core_clk_rate = <360000000>;
> + media_noc_clk_rate = <288000000>;
> + };
> diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-drm.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-drm.txt
> new file mode 100644
> index 0000000..fd93026
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-drm.txt
> @@ -0,0 +1,66 @@
> +Hisilicon DRM master device
> +
> +The Hisilicon DRM master device is a virtual device needed to list all
> +the other display relevant nodes that comprise the display subsystem.
There is no need for this in DT. The ADE can be the master device and
of-graph can link to the DSI node. I have a similar example here[1]
with a LCD controller block, DSI block and adv7533.
> +Required properties:
> +- compatible: Should be "hisilicon,<chip>-dss"
> +- #address-cells: should be set to 2.
> +- #size-cells: should be set to 2.
> +- range: to allow probing of subdevices.
> +
> +Optional properties:
> +- dma-coherent: Present if dma operations are coherent.
Put this on the actually DMA master.
Rob
[1] https://git.linaro.org/people/rob.herring/linux.git pxa1928-drm-v2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
