The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we have gpios for card detection, write-protect, vqmmc and vmmc. This patch adds pinmux for this sdcard interface, then adds regulators for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties. Signed-off-by: Jisheng Zhang <jszhang@xxxxxxxxxxx> --- since v1: - move sd1_pmux to soc dtsi - remove cd-inverted and make cd-gpio GPIO_ACTIVE_LOW arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 37 ++++++++++++++++++++++++++++-- arch/arm/boot/dts/berlin2q.dtsi | 5 ++++ 2 files changed, 40 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts index cdcf89b..33b2875 100644 --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts @@ -84,12 +84,45 @@ gpio = <&portb 12 GPIO_ACTIVE_HIGH>; enable-active-high; }; + + reg_sdio1_vmmc: regulator@3 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "sdio1_vmmc"; + enable-active-high; + regulator-boot-on; + gpio = <&portb 21 GPIO_ACTIVE_HIGH>; + }; + + reg_sdio1_vqmmc: regulator@4 { + compatible = "regulator-gpio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "sdio1_vqmmc"; + regulator-type = "voltage"; + enable-active-high; + gpios = <&portb 16 GPIO_ACTIVE_HIGH>; + states = <3300000 0x1 + 1800000 0x0>; + }; + }; +}; + +&soc_pinctrl { + sd1gpio_pmux: sd1pwr-pmux { + groups = "G23", "G32"; + function = "gpio"; }; }; &sdhci1 { - broken-cd; - sdhci,wp-inverted; + vmmc-supply = <®_sdio1_vmmc>; + vqmmc-supply = <®_sdio1_vqmmc>; + cd-gpios = <&portc 30 GPIO_ACTIVE_LOW>; + wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>; + pinctrl-names = "default"; status = "okay"; }; diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index 8ea177f..73a9362 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -417,6 +417,11 @@ soc_pinctrl: pin-controller { compatible = "marvell,berlin2q-soc-pinctrl"; + sd1_pmux: sd1-pmux { + groups = "G31"; + function = "sd1"; + }; + twsi0_pmux: twsi0-pmux { groups = "G6"; function = "twsi0"; -- 2.6.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html