[PATCH v2 9/9] regulator: add LM363X driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




LM363X regulator driver supports LM3631 and LM3632.
LM3631 has 5 regulators. LM3632 provides 3 regulators.
One boost output and LDOs are used for the display module.
Boost voltage is configurable but always on.
Supported operations for LDOs are enabled/disabled and voltage change.

Two LDOs of LM3632 can be controlled by external pins.
Those are configured through the DT properties.

Cc: Mark Brown <broonie@xxxxxxxxxx>
Cc: Lee Jones <lee.jones@xxxxxxxxxx> 
Cc: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-leds@xxxxxxxxxxxxxxx 
Cc: linux-kernel@xxxxxxxxxxxxxxx
Signed-off-by: Milo Kim <milo.kim@xxxxxx>
---
 drivers/regulator/Kconfig            |   9 +
 drivers/regulator/Makefile           |   1 +
 drivers/regulator/lm363x-regulator.c | 309 +++++++++++++++++++++++++++++++++++
 3 files changed, 319 insertions(+)
 create mode 100644 drivers/regulator/lm363x-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 3e028d9..971ebfa 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -274,6 +274,15 @@ config REGULATOR_ISL6271A
 	help
 	  This driver supports ISL6271A voltage regulator chip.
 
+config REGULATOR_LM363X
+	tristate "TI LM363X voltage regulators"
+	depends on MFD_TI_LMU
+	help
+	  This driver supports LM3631 and LM3632 voltage regulators for
+	  the LCD bias.
+	  One boost output voltage is configurable and always on.
+	  Other LDOs are used for the display module.
+
 config REGULATOR_LP3971
 	tristate "National Semiconductors LP3971 PMIC regulator driver"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 5a963d9..21a3e67 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o
 obj-$(CONFIG_REGULATOR_HI6421) += hi6421-regulator.o
 obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
 obj-$(CONFIG_REGULATOR_ISL9305) += isl9305.o
+obj-$(CONFIG_REGULATOR_LM363X) += lm363x-regulator.o
 obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
 obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
 obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
diff --git a/drivers/regulator/lm363x-regulator.c b/drivers/regulator/lm363x-regulator.c
new file mode 100644
index 0000000..e1b683e
--- /dev/null
+++ b/drivers/regulator/lm363x-regulator.c
@@ -0,0 +1,309 @@
+/*
+ * TI LM363X Regulator Driver
+ *
+ * Copyright 2015 Texas Instruments
+ *
+ * Author: Milo Kim <milo.kim@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/mfd/ti-lmu.h>
+#include <linux/mfd/ti-lmu-register.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/slab.h>
+
+/* LM3631 */
+#define LM3631_BOOST_VSEL_MAX		0x25
+#define LM3631_LDO_VSEL_MAX		0x28
+#define LM3631_CONT_VSEL_MAX		0x03
+#define LM3631_VBOOST_MIN		4500000
+#define LM3631_VCONT_MIN		1800000
+#define LM3631_VLDO_MIN			4000000
+#define ENABLE_TIME_USEC		1000
+
+/* LM3632 */
+#define LM3632_BOOST_VSEL_MAX		0x26
+#define LM3632_LDO_VSEL_MAX		0x29
+#define LM3632_VBOOST_MIN		4500000
+#define LM3632_VLDO_MIN			4000000
+
+/* Common */
+#define LM363X_STEP_50mV		50000
+#define LM363X_STEP_500mV		500000
+
+struct lm363x_regulator {
+	struct regmap *regmap;
+	struct regulator_dev *regulator;
+};
+
+const int ldo_cont_enable_time[] = {
+	0, 2000, 5000, 10000, 20000, 50000, 100000, 200000,
+};
+
+static int lm363x_regulator_enable_time(struct regulator_dev *rdev)
+{
+	struct lm363x_regulator *lm363x_regulator = rdev_get_drvdata(rdev);
+	enum lm363x_regulator_id id = rdev_get_id(rdev);
+	u8 val, addr, mask;
+
+	switch (id) {
+	case LM3631_LDO_CONT:
+		addr = LM3631_REG_ENTIME_VCONT;
+		mask = LM3631_ENTIME_CONT_MASK;
+		break;
+	case LM3631_LDO_OREF:
+		addr = LM3631_REG_ENTIME_VOREF;
+		mask = LM3631_ENTIME_MASK;
+		break;
+	case LM3631_LDO_POS:
+		addr = LM3631_REG_ENTIME_VPOS;
+		mask = LM3631_ENTIME_MASK;
+		break;
+	case LM3631_LDO_NEG:
+		addr = LM3631_REG_ENTIME_VNEG;
+		mask = LM3631_ENTIME_MASK;
+		break;
+	default:
+		return 0;
+	}
+
+	if (regmap_read(lm363x_regulator->regmap, addr, (unsigned int *)&val))
+		return -EINVAL;
+
+	val = (val & mask) >> LM3631_ENTIME_SHIFT;
+
+	if (id == LM3631_LDO_CONT)
+		return ldo_cont_enable_time[val];
+	else
+		return ENABLE_TIME_USEC * val;
+}
+
+static struct regulator_ops lm363x_boost_voltage_table_ops = {
+	.list_voltage     = regulator_list_voltage_linear,
+	.set_voltage_sel  = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel  = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops lm363x_regulator_voltage_table_ops = {
+	.list_voltage     = regulator_list_voltage_linear,
+	.set_voltage_sel  = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel  = regulator_get_voltage_sel_regmap,
+	.enable           = regulator_enable_regmap,
+	.disable          = regulator_disable_regmap,
+	.is_enabled       = regulator_is_enabled_regmap,
+	.enable_time      = lm363x_regulator_enable_time,
+};
+
+static const struct regulator_desc lm363x_regulator_desc[] = {
+	/* LM3631 */
+	{
+		.name           = "vboost",
+		.of_match	= "vboost",
+		.id             = LM3631_BOOST,
+		.ops            = &lm363x_boost_voltage_table_ops,
+		.n_voltages     = LM3631_BOOST_VSEL_MAX + 1,
+		.min_uV         = LM3631_VBOOST_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3631_REG_VOUT_BOOST,
+		.vsel_mask      = LM3631_VOUT_MASK,
+	},
+	{
+		.name           = "ldo_cont",
+		.of_match	= "vcont",
+		.id             = LM3631_LDO_CONT,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3631_CONT_VSEL_MAX + 1,
+		.min_uV         = LM3631_VCONT_MIN,
+		.uV_step        = LM363X_STEP_500mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3631_REG_VOUT_CONT,
+		.vsel_mask      = LM3631_VOUT_CONT_MASK,
+		.enable_reg     = LM3631_REG_LDO_CTRL2,
+		.enable_mask    = LM3631_EN_CONT_MASK,
+	},
+	{
+		.name           = "ldo_oref",
+		.of_match	= "voref",
+		.id             = LM3631_LDO_OREF,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3631_LDO_VSEL_MAX + 1,
+		.min_uV         = LM3631_VLDO_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3631_REG_VOUT_OREF,
+		.vsel_mask      = LM3631_VOUT_MASK,
+		.enable_reg     = LM3631_REG_LDO_CTRL1,
+		.enable_mask    = LM3631_EN_OREF_MASK,
+	},
+	{
+		.name           = "ldo_vpos",
+		.of_match	= "vpos",
+		.id             = LM3631_LDO_POS,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3631_LDO_VSEL_MAX + 1,
+		.min_uV         = LM3631_VLDO_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3631_REG_VOUT_POS,
+		.vsel_mask      = LM3631_VOUT_MASK,
+		.enable_reg     = LM3631_REG_LDO_CTRL1,
+		.enable_mask    = LM3631_EN_VPOS_MASK,
+	},
+	{
+		.name           = "ldo_vneg",
+		.of_match	= "vneg",
+		.id             = LM3631_LDO_NEG,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3631_LDO_VSEL_MAX + 1,
+		.min_uV         = LM3631_VLDO_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3631_REG_VOUT_NEG,
+		.vsel_mask      = LM3631_VOUT_MASK,
+		.enable_reg     = LM3631_REG_LDO_CTRL1,
+		.enable_mask    = LM3631_EN_VNEG_MASK,
+	},
+	/* LM3632 */
+	{
+		.name           = "vboost",
+		.of_match	= "vboost",
+		.id             = LM3632_BOOST,
+		.ops            = &lm363x_boost_voltage_table_ops,
+		.n_voltages     = LM3632_BOOST_VSEL_MAX + 1,
+		.min_uV         = LM3632_VBOOST_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3632_REG_VOUT_BOOST,
+		.vsel_mask      = LM3632_VOUT_MASK,
+	},
+	{
+		.name           = "ldo_vpos",
+		.of_match	= "vpos",
+		.id             = LM3632_LDO_POS,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3632_LDO_VSEL_MAX + 1,
+		.min_uV         = LM3632_VLDO_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3632_REG_VOUT_POS,
+		.vsel_mask      = LM3632_VOUT_MASK,
+		.enable_reg     = LM3632_REG_BIAS_CONFIG,
+		.enable_mask    = LM3632_EN_VPOS_MASK,
+	},
+	{
+		.name           = "ldo_vneg",
+		.of_match	= "vneg",
+		.id             = LM3632_LDO_NEG,
+		.ops            = &lm363x_regulator_voltage_table_ops,
+		.n_voltages     = LM3632_LDO_VSEL_MAX + 1,
+		.min_uV         = LM3632_VLDO_MIN,
+		.uV_step        = LM363X_STEP_50mV,
+		.type           = REGULATOR_VOLTAGE,
+		.owner          = THIS_MODULE,
+		.vsel_reg       = LM3632_REG_VOUT_NEG,
+		.vsel_mask      = LM3632_VOUT_MASK,
+		.enable_reg     = LM3632_REG_BIAS_CONFIG,
+		.enable_mask    = LM3632_EN_VNEG_MASK,
+	},
+};
+
+static int lm363x_regulator_of_get_enable_gpio(struct device_node *np, int id)
+{
+	/*
+	 * Check LCM_EN1/2_GPIO is configured.
+	 * Those pins are used for enabling VPOS/VNEG LDOs.
+	 */
+	switch (id) {
+	case LM3632_LDO_POS:
+		return of_get_named_gpio(np, "ti,lcm-en1-gpio", 0);
+	case LM3632_LDO_NEG:
+		return of_get_named_gpio(np, "ti,lcm-en2-gpio", 0);
+	default:
+		return -EINVAL;
+	}
+}
+
+static int lm363x_regulator_probe(struct platform_device *pdev)
+{
+	struct ti_lmu *lmu = dev_get_drvdata(pdev->dev.parent);
+	struct lm363x_regulator *lm363x_regulator;
+	struct regmap *regmap = lmu->regmap;
+	struct regulator_config cfg = { };
+	struct regulator_dev *rdev;
+	struct device *dev = &pdev->dev;
+	int id = pdev->id;
+	int ret, ena_gpio;
+
+	lm363x_regulator = devm_kzalloc(dev, sizeof(*lm363x_regulator),
+					GFP_KERNEL);
+	if (!lm363x_regulator)
+		return -ENOMEM;
+
+	lm363x_regulator->regmap = regmap;
+
+	cfg.dev = dev;
+	cfg.driver_data = lm363x_regulator;
+	cfg.regmap = regmap;
+
+	/*
+	 * LM3632 LDOs can be controlled by external pin.
+	 * Register update is required if the pin is used.
+	 */
+	ena_gpio = lm363x_regulator_of_get_enable_gpio(dev->of_node, id);
+	if (gpio_is_valid(ena_gpio)) {
+		cfg.ena_gpio = ena_gpio;
+		cfg.ena_gpio_flags = GPIOF_OUT_INIT_LOW;
+
+		ret = regmap_update_bits(regmap, LM3632_REG_BIAS_CONFIG,
+					 LM3632_EXT_EN_MASK,
+					 LM3632_EXT_EN_MASK);
+		if (ret) {
+			dev_err(dev, "External pin err: %d\n", ret);
+			return ret;
+		}
+	}
+
+	rdev = devm_regulator_register(dev, &lm363x_regulator_desc[id], &cfg);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(dev, "[%d] regulator register err: %d\n", id, ret);
+		return ret;
+	}
+
+	lm363x_regulator->regulator = rdev;
+	platform_set_drvdata(pdev, lm363x_regulator);
+
+	return 0;
+}
+
+static struct platform_driver lm363x_regulator_driver = {
+	.probe = lm363x_regulator_probe,
+	.driver = {
+		.name = "lm363x-regulator",
+	},
+};
+
+module_platform_driver(lm363x_regulator_driver);
+
+MODULE_DESCRIPTION("TI LM363X Regulator Driver");
+MODULE_AUTHOR("Milo Kim");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:lm363x-regulator");
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux