Add device tree bindings for the BCM6345/BCM6318 timers. This is required
for the BCM6345 watchdog which needs to respond to one of the timer
interrupts.
Signed-off-by: Simon Arlott <simon@xxxxxxxxxxx>
---
On 23/11/15 15:33, Jonas Gorski wrote:
> On Sat, Nov 21, 2015 at 8:02 PM, Simon Arlott <simon@xxxxxxxxxxx> wrote:
>> +- compatible: should be "brcm,bcm<soc>-timer", "brcm,bcm6345-timer"
>
> Since bcm6318 uses a slightly different register layout than the
> earlier SoCs, I'd argue that using bcm6345-timer as a compatible for
> bcm6318 is wrong.
I've split them out into two very similar bindings.
Patches 1/4 and 2/4 are replaced with (v2) 1/10 and (v2) 2/10.
.../bindings/timer/brcm,bcm6318-timer.txt | 44 ++++++++++++++++++++
.../bindings/timer/brcm,bcm6345-timer.txt | 47 ++++++++++++++++++++++
2 files changed, 91 insertions(+)
create mode 100644 Documentation/devicetree/bindings/timer/brcm,bcm6318-timer.txt
create mode 100644 Documentation/devicetree/bindings/timer/brcm,bcm6345-timer.txt
diff --git a/Documentation/devicetree/bindings/timer/brcm,bcm6318-timer.txt b/Documentation/devicetree/bindings/timer/brcm,bcm6318-timer.txt
new file mode 100644
index 0000000..cf4be7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/brcm,bcm6318-timer.txt
@@ -0,0 +1,44 @@
+Broadcom BCM6318 Timer
+
+This block is a timer that is connected to multiple interrupts on the main
+interrupt controller and functions as a programmable interrupt controller for
+timer events. There is a main timer interrupt for all timers.
+
+- 4 independent timers with their own interrupt, and own maskable level
+ interrupt bit in the main timer interrupt
+
+- 1 watchdog timer with an unmaskable level interrupt bit in the main timer
+ interrupt
+
+- Contains one enable/status word pair
+
+- No atomic set/clear operations
+
+Required properties:
+
+- compatible: should be "brcm,bcm<soc>-timer", "brcm,bcm6318-timer"
+- reg: specifies the base physical address and size of the registers, excluding
+ the watchdog registers
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+ source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+ this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+ node for the main timer interrupt, followed by the individual timer
+ interrupts; valid values depend on the type of parent interrupt controller
+- clocks: phandle of timer reference clock (periph)
+
+Example:
+
+timer: timer@10000040 {
+ compatible = "brcm,bcm63148-timer", "brcm,bcm6318-timer";
+ reg = <0x10000040 0x28>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&periph_intc>;
+ interrupts = <31>, <0>, <1>, <2>, <3>;
+ clock = <&periph_osc>;
+};
diff --git a/Documentation/devicetree/bindings/timer/brcm,bcm6345-timer.txt b/Documentation/devicetree/bindings/timer/brcm,bcm6345-timer.txt
new file mode 100644
index 0000000..03250dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/brcm,bcm6345-timer.txt
@@ -0,0 +1,47 @@
+Broadcom BCM6345 Timer
+
+This block is a timer that is connected to one interrupt on the main interrupt
+controller and functions as a programmable interrupt controller for timer
+events.
+
+- 3 independent timers with their own maskable level interrupt bit (but not
+ per CPU because there is only one parent interrupt and the timers share it)
+
+- 1 watchdog timer with an unmaskable level interrupt
+
+- Contains one enable/status word pair
+
+- No atomic set/clear operations
+
+The lack of per CPU ability of timers makes them unusable as a set of
+clockevent devices, otherwise they could be attached to the remaining
+interrupts.
+
+Required properties:
+
+- compatible: should be "brcm,bcm<soc>-timer", "brcm,bcm6345-timer"
+- reg: specifies the base physical address and size of the registers, excluding
+ the watchdog registers
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+ source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+ this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+ node for the timer interrupt; valid values depend on the type of parent
+ interrupt controller
+- clocks: phandle of timer reference clock (periph)
+
+Example:
+
+timer: timer@10000080 {
+ compatible = "brcm,bcm63168-timer", "brcm,bcm6345-timer";
+ reg = <0x10000080 0x1c>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&periph_intc>;
+ interrupts = <0>;
+ clock·=·<&periph_osc>;
+};
--
2.1.4
--
Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
