From: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>
Document the devicetree bindings for the clock driver found on Microchip
PIC32 class devices.
Signed-off-by: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>
Signed-off-by: Joshua Henderson <joshua.henderson@xxxxxxxxxxxxx>
---
.../devicetree/bindings/clock/microchip,pic32.txt | 263 ++++++++++++++++++++
1 file changed, 263 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/microchip,pic32.txt
diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
new file mode 100644
index 0000000..4cef72d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
@@ -0,0 +1,263 @@
+Binding for a Clock hardware block found on
+certain Microchip PIC32 MCU devices.
+
+Microchip SoC clocks-node consists of few oscillators, PLL, multiplexer
+and few divider nodes.
+
+We will find only the base address of the clock tree, this base
+address is common for some of the subnodes, not all. If no address is
+specified for any of subnode base address of the clock tree will be
+treated as its base. Each of subnodes follow the same common clock
+binding with some additional optional properties.
+
+ clocks_node {
+ reg = <>;
+
+ spll_node {
+ ...
+ };
+
+ frcdiv_node {
+ ...
+ };
+
+ sysclk_mux_node {
+ ...
+ };
+
+ pbdiv_node {
+ ...
+ };
+
+ refoclk_node {
+ ...
+ };
+ ...
+ };
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : should have "microchip,pic32-clk".
+- reg : A Base address and length of the register set.
+- interrupts : source of interrupt.
+
+Optional properties (for subnodes):
+- #clock-cells: From common clock binding, should be 0.
+
+- microchip,clock-indices: in multiplexer node clock sources always aren't linear
+ and contiguous. This property helps define clock-sources with respect to
+ the mux clock node.
+
+- microchip,ignore-unused : ignore gate request even if the gated clock is unused.
+- microchip,status-bit-mask: bitmask for status check. This will be used to confirm
+ particular operation by clock sub-node is completed. It is dependent sub-node.
+- microchip,bit-mask: enable mask, similar to microchip,status-bit-mask.
+- microchip,slew-step: enable frequency slewing(stepping) during rate change;
+ applicable only to sys-clock subnode.
+
+Example:
+
+/* PIC32 specific clks */
+pic32_clktree {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x1f801200 0x200>;
+ compatible = "microchip,pic32-clk";
+ interrupts = <12>;
+ ranges;
+
+ /* secondary oscillator; external input on SOSCI pin */
+ SOSC:sosc_clk {
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-sosc";
+ clock-frequency = <32768>;
+ reg = <0x1f801200 0x10 /* enable reg */
+ 0x1f801390 0x10>; /* status reg */
+ microchip,bit-mask = <0x02>; /* enable mask */
+ microchip,status-bit-mask = <0x10>; /* status-mask*/
+ };
+
+ FRCDIV:frcdiv_clk {
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-frcdivclk";
+ clocks = <&FRC>;
+ clock-output-names = "frcdiv_clk";
+ };
+
+ /* System PLL clock */
+ SYSPLL:spll_clk {
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-syspll";
+ reg = <0x1f801220 0x10 /* SPLL register */
+ 0x1f801390 0x10>; /* CLKSTAT register */
+ clocks = <&POSC>, <&FRC>;
+ clock-output-names = "sys_pll";
+ microchip,status-bit-mask = <0x80>; /* SPLLRDY */
+ };
+
+ /* system clock; mux with postdiv & slew */
+ SYSCLK:sys_clk {
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-sysclk-v2";
+ reg = <0x1f8013c0 0x04>; /* SLEWCON */
+ clocks = <&FRCDIV>, <&SYSPLL>, <&POSC>, <&SOSC>,
+ <&LPRC>, <&FRCDIV>;
+ microchip,clock-indices = <0>, <1>, <2>, <4>, <5>, <7>;
+ clock-output-names = "sys_clk";
+ };
+
+ /* DDR Ctrl & DDR PHY PLL */
+ MPLL: CLK_MPLL {
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-mpll";
+ reg = <0x1f800100 0x04>; /* CFGMPLL */
+ clocks = <&POSC>;
+ clock-output-names = "pic32-mpll";
+ status = "disabled";
+ };
+
+ /* Peripheral bus1 clock */
+ PBCLK1:pb1_clk {
+ reg = <0x1f801340 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ clock-output-names = "pb1_clk";
+ /* used by system modules, not gateable */
+ microchip,ignore-unused;
+ };
+
+ /* Peripheral bus2 clock */
+ PBCLK2:pb2_clk {
+ reg = <0x1f801350 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ clock-output-names = "pb2_clk";
+ /* avoid gating even if unused */
+ microchip,ignore-unused;
+ };
+
+ /* Peripheral bus3 clock */
+ PBCLK3:pb3_clk {
+ reg = <0x1f801360 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ clock-output-names = "pb3_clk";
+ };
+
+ /* Peripheral bus4 clock(I/O ports, GPIO) */
+ PBCLK4:pb4_clk {
+ reg = <0x1f801370 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ clock-output-names = "pb4_clk";
+ };
+
+ /* Peripheral bus clock */
+ PBCLK5:pb5_clk {
+ reg = <0x1f801380 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ clock-output-names = "pb5_clk";
+ };
+
+ /* Peripheral Bus6 clock; */
+ PBCLK6:pb6_clk {
+ reg = <0x1f801390 0x10>;
+ compatible = "microchip,pic32-pbclk";
+ clocks = <&SYSCLK>;
+ #clock-cells = <0>;
+ };
+
+ /* Peripheral bus7 clock */
+ PBCLK7:pb7_clk {
+ reg = <0x1f8013A0 0x10>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-pbclk";
+ /* CPU is driven by this clock; so named */
+ clock-output-names = "cpu_clk";
+ clocks = <&SYSCLK>;
+ };
+
+ /* Reference Oscillator clock for SPI/I2S */
+ REFCLKO1:refo1_clk {
+ reg = <0x1f801280 0x20>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-refoclk";
+ clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+ <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+ microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
+ <7>, <8>, <9>;
+ clock-output-names = "refo1_clk";
+ clock-frequency = <10000000>; /* 10Mhz for I2S MCLK */
+ };
+
+ /* Reference Oscillator clock for SQI */
+ REFCLKO2:refo2_clk {
+ reg = <0x1f8012A0 0x20>;
+ #clock-cells = <0>;
+ compatible = "microchip,pic32-refoclk";
+ clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+ <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+ microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
+ <7>, <8>, <9>;
+ clock-output-names = "refo2_clk";
+ clock-frequency = <50000000>; /* 50MHz for SQI */
+ };
+
+ /* Reference Oscillator clock, ADC */
+ REFCLKO3:refo3_clk {
+ reg = <0x1f8012C0 0x20>;
+ compatible = "microchip,pic32-refoclk";
+ clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+ <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+ microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
+ <7>, <8>, <9>;
+ #clock-cells = <0>;
+ clock-output-names = "refo3_clk";
+ clock-frequency = <10000000>; /* 1Mhz */
+ };
+
+ /* Reference Oscillator clock */
+ REFCLKO4:refo4_clk {
+ reg = <0x1f8012E0 0x20>;
+ compatible = "microchip,pic32-refoclk";
+ clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+ <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+ microchip,clock-indices = <0>,<1>,<2>,<3>,<4>,<5>,<7>,
+ <8>,<9>;
+ #clock-cells = <0>;
+ clock-output-names = "refo4_clk";
+ clock-frequency = <25000000>; /* 25Mhz */
+ };
+
+ /* Reference Oscillator clock, LCD */
+ REFCLKO5:refo5_clk {
+ reg = <0x1f801300 0x20>;
+ compatible = "microchip,pic32-refoclk";
+ clocks = <&SYSCLK>,<&PBCLK1>,<&POSC>,<&FRC>,<&LPRC>,
+ <&SOSC>,<&SYSPLL>,<&REFIx>,<&BFRC>;
+ microchip,clock-indices = <0>, <1>, <2>, <3>, <4>, <5>,
+ <7>, <8>,<9>;
+ #clock-cells = <0>;
+ clock-output-names = "refo5_clk";
+ clock-frequency = <40000000>; /* 40Mhz */
+ };
+};
+
+The clock consumer should specify the desired clock by having the clocks in its
+"clock" phandle cell. For example for UART:
+
+uart2: serial@<> {
+ compatible = "microchip,pic32-uart";
+ reg = <>;
+ interrupts = <>;
+ clocks = <&PBCLK2>;
+}
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
