Hi,
On 17-11-15 17:12, Jens Kuske wrote:
Enable the 2 USB host controllers used on the Orange Pi Plus
and add the necessary regulators.
Signed-off-by: Reinder de Haan <patchesrdh@xxxxxxxxx>
Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
Signed-off-by: Jens Kuske <jenskuske@xxxxxxxxx>
---
Hi Hans,
with these regulators USB works on the Orange Pi Plus too.
I don't know if adding the regulators in the dts is okay, since most
regulators are defined in the sunxi-common-regulators.dtsi, but
we use different pins.
Thanks, I've added this to my sunxi-wip branch for now.
Regards,
Hans
p.s.
Any progress on getting the "core" H3 kernel support upstream ?
Given Arnd's remarks about how we should not hard-code the
indices in the clk driver + the very KISS nature of the
change to 1 parent-clk per gate setup I still believe
that that one is best.
Maxime ? Chen-Yu ? It would be really good to be able to
move forward with this, how do you want to proceed ?
Jens
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 44 ++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
index e67df59..1cb6c66 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -58,6 +58,35 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb3_vbus_pin_a>;
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&pio {
+ usb3_vbus_pin_a: usb3_vbus_pin@0 {
+ allwinner,pins = "PG11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&mmc0 {
@@ -70,8 +99,23 @@
status = "okay";
};
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb3_vbus-supply = <®_usb3_vbus>;
+ status = "okay";
+};
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
