On Mon, Nov 09, 2015 at 04:39:37PM +0200, Andy Shevchenko wrote:
> On Mon, Nov 9, 2015 at 12:13 PM, Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> wrote:
> > This adds support for the Mediatek thermal controller found on MT8173
> > and likely other SoCs.
> > The controller is a bit special. It does not have its own ADC, instead
> > it controls the on-SoC AUXADC via AHB bus accesses. For this reason
> > we need the physical address of the AUXADC. Also it controls a mux
> > using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.
>
> Few style nitpicks.
>
>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/nvmem-consumer.h>
> > +#include <linux/of.h>
> > +#include <linux/of_address.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/slab.h>
> > +#include <linux/io.h>
> > +#include <linux/thermal.h>
> > +#include <linux/reset.h>
> > +#include <linux/types.h>
> > +#include <linux/nvmem-consumer.h>
> > +
> > +/* AUXADC Registers */
> > +#define AUXADC_CON0_V 0x000
> > +#define AUXADC_CON1_V 0x004
> > +#define AUXADC_CON1_SET_V 0x008
> > +#define AUXADC_CON1_CLR_V 0x00c
> > +#define AUXADC_CON2_V 0x010
> > +#define AUXADC_DATA(channel) (0x14 + (channel) * 4)
> > +#define AUXADC_MISC_V 0x094
> > +
> > +#define AUXADC_CON1_CHANNEL(x) BIT(x)
> > +
> > +#define APMIXED_SYS_TS_CON1 0x604
> > +
> > +/* Thermal Controller Registers */
> > +#define TEMP_MONCTL0 0x000
> > +#define TEMP_MONCTL1 0x004
> > +#define TEMP_MONCTL2 0x008
> > +#define TEMP_MONIDET0 0x014
> > +#define TEMP_MONIDET1 0x018
> > +#define TEMP_MSRCTL0 0x038
> > +#define TEMP_AHBPOLL 0x040
> > +#define TEMP_AHBTO 0x044
> > +#define TEMP_ADCPNP0 0x048
> > +#define TEMP_ADCPNP1 0x04c
> > +#define TEMP_ADCPNP2 0x050
> > +#define TEMP_ADCPNP3 0x0b4
> > +
> > +#define TEMP_ADCMUX 0x054
> > +#define TEMP_ADCEN 0x060
> > +#define TEMP_PNPMUXADDR 0x064
> > +#define TEMP_ADCMUXADDR 0x068
> > +#define TEMP_ADCENADDR 0x074
> > +#define TEMP_ADCVALIDADDR 0x078
> > +#define TEMP_ADCVOLTADDR 0x07c
> > +#define TEMP_RDCTRL 0x080
> > +#define TEMP_ADCVALIDMASK 0x084
> > +#define TEMP_ADCVOLTAGESHIFT 0x088
> > +#define TEMP_ADCWRITECTRL 0x08c
> > +#define TEMP_MSR0 0x090
> > +#define TEMP_MSR1 0x094
> > +#define TEMP_MSR2 0x098
> > +#define TEMP_MSR3 0x0B8
> > +
> > +#define TEMP_SPARE0 0x0f0
> > +
> > +#define PTPCORESEL 0x400
> > +
> > +#define TEMP_MONCTL1_PERIOD_UNIT(x) ((x) & 0x3ff)
> > +
> > +#define TEMP_MONCTL2_FILTER_INTERVAL(x) (((x) & 0x3ff)) << 16
> > +#define TEMP_MONCTL2_SENSOR_INTERVAL(x) ((x) & 0x3ff)
> > +
> > +#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x) (x)
> > +
> > +#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE BIT(0)
> > +#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE BIT(1)
> > +
> > +#define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5)
> > +#define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit)
> > +
> > +#define MT8173_TS1 0
> > +#define MT8173_TS2 1
> > +#define MT8173_TS3 2
> > +#define MT8173_TS4 3
> > +#define MT8173_TSABB 4
> > +
> > +/* AUXADC channel 11 is used for the temperature sensors */
> > +#define MT8173_TEMP_AUXADC_CHANNEL 11
> > +
> > +/* The total number of temperature sensors in the MT8173 */
> > +#define MT8173_NUM_SENSORS 5
> > +
> > +/* The number of banks in the MT8173 */
> > +#define MT8173_NUM_ZONES 4
> > +
> > +/* The number of sensing points per bank */
> > +#define MT8173_NUM_SENSORS_PER_ZONE 4
> > +
> > +/* Layout of the fuses providing the calibration data */
> > +#define MT8173_CALIB_BUF0_VALID (1 << 0)
> > +#define MT8173_CALIB_BUF1_ADC_GE(x) (((x) >> 22 ) & 0x3ff)
> > +#define MT8173_CALIB_BUF0_VTS_TS1(x) (((x) >> 17 ) & 0x1ff)
> > +#define MT8173_CALIB_BUF0_VTS_TS2(x) (((x) >> 8 ) & 0x1ff)
> > +#define MT8173_CALIB_BUF1_VTS_TS3(x) (((x) >> 0 ) & 0x1ff)
> > +#define MT8173_CALIB_BUF2_VTS_TS4(x) (((x) >> 23 ) & 0x1ff)
> > +#define MT8173_CALIB_BUF2_VTS_TSABB(x) (((x) >> 14 ) & 0x1ff)
> > +#define MT8173_CALIB_BUF0_DEGC_CALI(x) (((x) >> 1 ) & 0x3f)
> > +#define MT8173_CALIB_BUF0_O_SLOPE(x) (((x) >> 26 ) & 0x3f)
> > +
> > +#define THERMAL_NAME "mtk-thermal"
> > +
> > +struct mtk_thermal;
> > +
> > +struct mtk_thermal_bank {
> > + struct mtk_thermal *mt;
> > + int id;
> > +};
> > +
> > +struct mtk_thermal {
> > + struct device *dev;
> > + void __iomem *thermal_base;
> > +
> > + struct clk *clk_peri_therm;
> > + struct clk *clk_auxadc;
> > +
> > + struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
> > +
> > + struct mutex lock;
> > +
> > + /* Calibration values */
> > + s32 adc_ge;
> > + s32 degc_cali;
> > + s32 o_slope;
> > + s32 vts[MT8173_NUM_SENSORS];
> > +
> > + struct thermal_zone_device *tzd;
> > +};
> > +
> > +struct mtk_thermal_bank_cfg {
> > + unsigned int num_sensors;
> > + unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
> > +};
> > +
> > +static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
> > +
> > +/*
> > + * The MT8173 thermal controller has four banks. Each bank can read up to
> > + * four temperature sensors simultaneously. The MT8173 has a total of 5
> > + * temperature sensors. We use each bank to measure a certain area of the
> > + * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
> > + * areas, hence is used in different banks.
> > + */
> > +static const struct mtk_thermal_bank_cfg bank_data[] = {
> > + {
> > + .num_sensors = 2,
> > + .sensors = { MT8173_TS2, MT8173_TS3 },
> > + }, {
> > + .num_sensors = 2,
> > + .sensors = { MT8173_TS2, MT8173_TS4 },
> > + }, {
> > + .num_sensors = 3,
> > + .sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
> > + }, {
> > + .num_sensors = 1,
> > + .sensors = { MT8173_TS2 },
> > + },
> > +};
> > +
> > +struct mtk_thermal_sense_point {
> > + int msr;
> > + int adcpnp;
> > +};
> > +
> > +static const struct mtk_thermal_sense_point
> > + sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
> > + {
> > + .msr = TEMP_MSR0,
> > + .adcpnp = TEMP_ADCPNP0,
> > + }, {
> > + .msr = TEMP_MSR1,
> > + .adcpnp = TEMP_ADCPNP1,
> > + }, {
> > + .msr = TEMP_MSR2,
> > + .adcpnp = TEMP_ADCPNP2,
> > + }, {
> > + .msr = TEMP_MSR3,
> > + .adcpnp = TEMP_ADCPNP3,
> > + },
> > +};
> > +
> > +/**
> > + * raw_to_mcelsius - convert a raw ADC value to mcelsius
> > + * @mt: The thermal controller
> > + * @raw: raw ADC value
> > + *
> > + * This converts the raw ADC value to mcelsius using the SoC specific
> > + * calibration constants
> > + */
> > +static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
> > +{
> > + s32 tmp;
> > +
> > + raw &= 0xfff;
> > +
> > + tmp = 203450520 << 3;
> > + tmp /= 165 + mt->o_slope;
> > + tmp /= 10000 + mt->adc_ge;
> > + tmp *= raw - mt->vts[sensno] - 3350;
> > + tmp >>= 3;
> > +
> > + return mt->degc_cali * 500 - tmp;
> > +}
> > +
> > +/**
> > + * mtk_thermal_get_bank - get bank
> > + * @bank: The bank
> > + *
> > + * The bank registers are banked, we have to select a bank in the
> > + * PTPCORESEL register to access it.
> > + */
> > +static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
> > +{
> > + struct mtk_thermal *mt = bank->mt;
> > + u32 val;
> > +
> > + mutex_lock(&mt->lock);
> > +
> > + val = readl(mt->thermal_base + PTPCORESEL);
> > + val &= ~0xf;
> > + val |= bank->id;
> > + writel(val, mt->thermal_base + PTPCORESEL);
> > +}
> > +
> > +/**
> > + * mtk_thermal_put_bank - release bank
> > + * @bank: The bank
> > + *
> > + * release a bank previously taken with mtk_thermal_get_bank,
> > + */
> > +static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
> > +{
> > + struct mtk_thermal *mt = bank->mt;
> > +
> > + mutex_unlock(&mt->lock);
> > +}
> > +
> > +/**
> > + * mtk_thermal_bank_temperature - get the temperature of a bank
> > + * @bank: The bank
> > + *
> > + * The temperature of a bank is considered the maximum temperature of
> > + * the sensors associated to the bank.
> > + */
> > +static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> > +{
> > + struct mtk_thermal *mt = bank->mt;
> > + int temp, i, max;
> > + u32 raw;
> > +
> > + temp = max = INT_MIN;
> > +
> > + for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
> > + raw = readl(mt->thermal_base + sensing_points[i].msr);
> > +
> > + temp = raw_to_mcelsius(mt, bank_data[bank->id].sensors[i], raw);
> > +
> > + /*
> > + * The first read of a sensor often contains very high bogus
> > + * temperature value. Filter these out so that the system does
> > + * not immediately shut down.
> > + */
> > + if (temp > 200000)
> > + temp = 0;
> > +
> > + if (temp > max)
> > + max = temp;
> > + }
> > +
> > + return max;
> > +}
> > +
> > +static int mtk_read_temp(void *data, int *temperature)
> > +{
> > + struct mtk_thermal *mt = data;
> > + int i;
> > + int tempmax = INT_MIN;
> > +
> > + for (i = 0; i < MT8173_NUM_ZONES; i++) {
> > + struct mtk_thermal_bank *bank = &mt->banks[i];
> > + int t;
> > +
> > + mtk_thermal_get_bank(bank);
> > +
> > + t = mtk_thermal_bank_temperature(bank);
> > +
> > + mtk_thermal_put_bank(bank);
> > +
> > + if (t > tempmax)
> > + tempmax = t;
>
> Would it be
> tempmax = max_t(int, tempmax, mtk_thermal_bank_temperature(bank));
> ?
Yes, even max() works here. Fixed.
> > +
> > + mtk_thermal_get_bank(bank);
> > +
> > + /* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
> > + writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
> > +
> > + /*
> > + * filt interval is 1 * 46.540us = 46.54us,
> > + * sen interval is 429 * 46.540us = 19.96ms
> > + */
> > + writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
> > + TEMP_MONCTL2_SENSOR_INTERVAL(429),
> > + mt->thermal_base + TEMP_MONCTL2);
> > +
> > + /* poll is set to 10u */
> > + writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
> > + mt->thermal_base + TEMP_AHBPOLL);
> > +
> > + /* temperature sampling control, 1 sample */
> > + writel(0x00000000, mt->thermal_base + TEMP_MSRCTL0);
>
> 0x0 like below ?
Ok.
> > +static struct platform_driver mtk_thermal_driver = {
> > + .probe = mtk_thermal_probe,
> > + .remove = mtk_thermal_remove,
> > + .driver = {
> > + .name = THERMAL_NAME,
> > + .of_match_table = mtk_thermal_of_match,
> > + },
> > +};
> > +
> > +module_platform_driver(mtk_thermal_driver);
> > +
> > +MODULE_AUTHOR("Sascha Hauer <s.hauer@xxxxxxxxxxxxxx");
>
> And Author in the head?
Added.
Thanks for reviewing.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
