ARM's Juno board has two HDLCD controllers, each linked to an NXP TDA19988 HDMI transmitter that provides output encoding. Add them to the device tree. Signed-off-by: Liviu Dudau <Liviu.Dudau@xxxxxxx> --- arch/arm64/boot/dts/arm/juno-base.dtsi | 74 ++++++++++++++++++++++++++++++++-- 1 file changed, 70 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index dd5158e..ebb313a 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -92,8 +92,8 @@ scpi_clk: scpi_clocks@3 { compatible = "arm,scpi-variable-clocks"; #clock-cells = <1>; - clock-indices = <3>, <4>; - clock-output-names = "pxlclk0", "pxlclk1"; + clock-indices = <3>; + clock-output-names = "pxlclk"; }; }; @@ -123,6 +123,34 @@ clock-names = "apb_pclk"; }; + hdlcd@7ff50000 { + compatible = "arm,hdlcd"; + reg = <0 0x7ff50000 0 0x1000>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&scpi_clk 3>; + clock-names = "pxlclk"; + + port { + hdlcd1_output: endpoint@0 { + remote-endpoint = <&tda998x_1_input>; + }; + }; + }; + + hdlcd@7ff60000 { + compatible = "arm,hdlcd"; + reg = <0 0x7ff60000 0 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&scpi_clk 3>; + clock-names = "pxlclk"; + + port { + hdlcd0_output: endpoint@0 { + remote-endpoint = <&tda998x_0_input>; + }; + }; + }; + soc_uart0: uart@7ff80000 { compatible = "arm,pl011", "arm,primecell"; reg = <0x0 0x7ff80000 0x0 0x1000>; @@ -141,14 +169,32 @@ i2c-sda-hold-time-ns = <500>; clocks = <&soc_smc50mhz>; - dvi0: dvi-transmitter@70 { + hdmi-transmitter@70 { compatible = "nxp,tda998x"; reg = <0x70>; + port { + tda998x_0_input: endpoint@0 { + remote-endpoint = <&hdlcd0_output>; + }; + + tda998x_0_output: endpoint@1 { + remote-endpoint = <&hdmi0_connector_output>; + }; + }; }; - dvi1: dvi-transmitter@71 { + hdmi-transmitter@71 { compatible = "nxp,tda998x"; reg = <0x71>; + port { + tda998x_1_input: endpoint@0 { + remote-endpoint = <&hdlcd1_output>; + }; + + tda998x_1_output: endpoint@1 { + remote-endpoint = <&hdmi1_connector_output>; + }; + }; }; }; @@ -182,6 +228,26 @@ <0x00000008 0x80000000 0x1 0x80000000>; }; + hdmi0: connector@0 { + compatible = "hdmi-connector"; + type = "a"; + port { + hdmi0_connector_output: endpoint { + remote-endpoint = <&tda998x_0_output>; + }; + }; + }; + + hdmi1: connector@1 { + compatible = "hdmi-connector"; + type = "a"; + port { + hdmi1_connector_output: endpoint { + remote-endpoint = <&tda998x_1_output>; + }; + }; + }; + smb { compatible = "simple-bus"; #address-cells = <2>; -- 2.6.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html