Hi Pramod,
On 10/26/2015 10:08 AM, Pramod Kumar wrote:
-----Original Message-----
From: Ray Jui [mailto:rjui@xxxxxxxxxxxx]
Sent: 23 October 2015 21:38
To: Laurent Pinchart; Rob Herring
Cc: Pramod Kumar; Pawel Moll; Mark Rutland; Ian Campbell; Kumar Gala; Scott
Branden; Russell King; Linus Walleij; linux-gpio@xxxxxxxxxxxxxxx; bcm-kernel-
feedback-list; Jason Uy; Masahiro Yamada; Thomas Gleixner;
devicetree@xxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-
kernel@xxxxxxxxxxxxxxx; Jonas Gorski
Subject: Re: [PATCH 05/11] dt-binding: Add ngpios property to GPIO controller
node
On 10/23/2015 6:02 AM, Laurent Pinchart wrote:
Hi Rob,
On Friday 23 October 2015 06:51:28 Rob Herring wrote:
On Fri, Oct 23, 2015 at 4:08 AM, Laurent Pinchart wrote:
On Thursday 22 October 2015 18:41:05 Rob Herring wrote:
On Thu, Oct 22, 2015 at 1:52 PM, Ray Jui wrote:
On 10/22/2015 11:43 AM, Rob Herring wrote:
On Mon, Oct 19, 2015 at 12:43 AM, Pramod Kumar wrote:
Add ngpios property to the gpio controller's DT node so that
controller driver extracts total number of gpio lines present in
controller from DT and removes dependency on driver.
Signed-off-by: Pramod Kumar <pramodku@xxxxxxxxxxxx>
Reviewed-by: Ray Jui <rjui@xxxxxxxxxxxx>
Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
---
Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt | 5
+++
1 file changed, 5 insertions(+)
diff --git
a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
index f92b833..655a8d7 100644
---
a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio
+++ .txt
@@ -10,6 +10,9 @@ Required properties:
Define the base and range of the I/O address space that
contains
the Cygnus
GPIO/PINCONF controller registers
+- ngpios:
+ Total number of GPIOs the controller provides
This must be optional for compatibility and the driver needs to
handle it not present.
You meant to be compatible with existing Cygnus devices, correct?
Just to clarify, here you suggest we still leave the existing hard
coded ngpios in the driver, in order to be compatible with all
existing Cygnus devices (while the Cygnus device tree changes to
use ngpio is still being merged and through different maintainer),
and have all new iProc SoCs switch to use ngpios from device tree, right?
Yes, an existing dtb should continue to work with a new kernel. You
can add the DT property to the older devices too and then
eventually remove the hard coded values some time in the future.
That could be immediately (don't care about compatibility at all),
a couple of kernel cycles, never... It all depends on users of the
impacted platforms.
But shouldn't the property still be documented as required to ensure
that new DTs always include it ?
Good point. If the intent is to eventually remove it from the driver,
then yes. We probably need "required for new designs" as a category
or maybe "recommended"? The wording is not so important here, but I'm
thinking about as we try to standardize the naming.
Required for new designs sounds better than recommended. Or maybe
something like "Required (optional for backward compatibility)".
Yes, it should be phrased as "required for new designs" because all new iProc
SoCs using this GPIO driver need to have this in DT.
Thanks,
Ray
Thanks for providing feedback. I'll make sure to use this property under phrase " required for new designs " in next patch set.
Regards,
Pramod
To confirm, is your plan:
1) Continue to support hardcoded ngpios in the driver for the current
SoC Cygnus
2) Proceed with Cygnus DTS changes to switch to DT based ngpios
configuration
3) Modify the document to make DT ngpios a required property for all new
SoCs including NSP, NS2, and etc.
?
Thanks,
Ray
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html