Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:
- Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
to be splitted for submission of RTC part first;
- Front LCD (Winstar 1602G): driver needs to be written
- Armada NAND controller (to access onboard 128MB of NAND): support
being pushed by @free-electrons people
- 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
driver is available upstream. Not referenced/tested yet.
but the device is usable w/o those.
Signed-off-by: Arnaud Ebalard <arno@xxxxxxxxxxxx>
---
Jason and Andrew,
I do not think there is any good way to share much between RN102 and
RN104 .dts in a common .dtsi file because MPP are used in a different
fashion on the two boards. But if you have ideas ...
I do intend to document the hardware parts and setup of the device as I
did for the Duo v2 and RN102 but I wanted to get the patch submitted for
inclusion in 3.13 first.
Comments welcome,
Cheers,
a+
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/armada-370-netgear-rn104.dts | 197 +++++++++++++++++++++++++
2 files changed, 198 insertions(+)
create mode 100644 arch/arm/boot/dts/armada-370-netgear-rn104.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 802720e..be682cb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -108,6 +108,7 @@ dtb-$(CONFIG_ARCH_MSM) += msm8660-surf.dtb \
dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
armada-370-mirabox.dtb \
armada-370-netgear-rn102.dtb \
+ armada-370-netgear-rn104.dtb \
armada-370-rd.dtb \
armada-xp-axpwifiap.dtb \
armada-xp-db.dtb \
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
new file mode 100644
index 0000000..e3855e8
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts
@@ -0,0 +1,197 @@
+/*
+ * Device Tree file for NETGEAR ReadyNAS 104
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@xxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+
+/ {
+ model = "NETGEAR ReadyNAS 104";
+ compatible = "netgear,readynas-104", "marvell,armada370", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /* Connected to FL1009 USB 3.0 controller */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected to Marvell 88SE9215 SATA controller */
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+ serial@12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
+ };
+
+ sata@a0000 {
+ status = "disabled";
+ };
+
+ pinctrl {
+ poweroff: poweroff {
+ marvell,pins = "mpp60";
+ marvell,function = "gpio";
+ };
+
+ backup_key_pin: backup-key-pin {
+ marvell,pins = "mpp52";
+ marvell,function = "gpio";
+ };
+
+ power_key_pin: power-key-pin {
+ marvell,pins = "mpp62";
+ marvell,function = "gpio";
+ };
+
+ backup_led_pin: backup-led-pin {
+ marvell,pins = "mpp63";
+ marvell,function = "gpo";
+ };
+
+ power_led_pin: power-led-pin {
+ marvell,pins = "mpp64";
+ marvell,function = "gpio";
+ };
+
+ reset_key_pin: reset-key-pin {
+ marvell,pins = "mpp65";
+ marvell,function = "gpio";
+ };
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ usb@50000 {
+ status = "okay";
+ };
+
+ i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ clock-frequency = <100000>;
+ status = "okay";
+
+ g762: g762@3e {
+ compatible = "gmt,g762";
+ reg = <0x3e>;
+ clocks = <&g762_clk>; /* input clock */
+ fan_gear_mode = <0>;
+ fan_startv = <1>;
+ pwm_polarity = <0>;
+ };
+ };
+ };
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ g762_clk: fixedclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <8192>;
+ };
+ };
+
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&backup_led_pin &power_led_pin>;
+ pinctrl-names = "default";
+
+ blue_backup_led {
+ label = "rn104:blue:backup";
+ gpios = <&gpio1 31 1>; /* GPIO 63 Active Low */
+ default-state = "on";
+ };
+
+ blue_power_led {
+ label = "rn104:blue:pwr";
+ gpios = <&gpio2 0 1>; /* GPIO 64 Active Low */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&backup_key_pin
+ &power_key_pin
+ &reset_key_pin>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "Backup Button";
+ linux,code = <133>; /* KEY_COPY */
+ gpios = <&gpio1 20 1>;
+ };
+
+ button@2 {
+ label = "Power Button";
+ linux,code = <116>; /* KEY_POWER */
+ gpios = <&gpio1 30 0>;
+ };
+
+ button@3 {
+ label = "Reset Button";
+ linux,code = <0x198>; /* KEY_RESTART */
+ gpios = <&gpio2 1 1>;
+ };
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&poweroff>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 28 1>;
+ };
+};
--
1.8.4.rc3
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
