Re: [PATCH v2 1/4] i2c: busses: i2c-st: Add ST I2C controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi,

Please make one mail thread out of a patch series. That helps reviewing.

On Thu, Sep 26, 2013 at 11:53:58AM +0200, Maxime COQUELIN wrote:
> This patch adds support to SSC (Synchronous Serial Controller)
> I2C driver. This IP also supports SPI protocol, but this is not
> the aim of this driver.
> 
> This IP is embedded in all ST SoCs for Set-top box platorms, and
> supports I2C Standard and Fast modes.
> 
> Signed-off-by: Maxime Coquelin <maxime.coquelin@xxxxxx>
> Cc: Srinivas Kandagatla <srinivas.kandagatla@xxxxxx>
> ---
>  Documentation/devicetree/bindings/i2c/i2c-st.txt |   37 ++
>  drivers/i2c/busses/Kconfig                       |   10 +
>  drivers/i2c/busses/Makefile                      |    1 +
>  drivers/i2c/busses/i2c-st.c                      |  691 ++++++++++++++++++++++
>  drivers/i2c/busses/i2c-st.h                      |  208 +++++++
>  5 files changed, 947 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/i2c/i2c-st.txt
>  create mode 100644 drivers/i2c/busses/i2c-st.c
>  create mode 100644 drivers/i2c/busses/i2c-st.h
> 
> diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
> new file mode 100644
> index 0000000..d1e55c0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt
> @@ -0,0 +1,37 @@
> +ST SSC binding, for I2C mode operation
> +
> +Required properties :
> +- compatible : Must be "st,comms-i2c"
> +- reg : Offset and length of the register set for the device
> +- interrupts : the interrupt specifier
> +- clocks : phandle to the I2C clock source
> +- clock-names : from common clock binding: Shall be "ssc"
> +
> +Recommended properties :
> +- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise
> +  the default 100 kHz frequency will be used. As only Normal and Fast modes
> +  are supported, possible values are 100000 and 400000.
> +
> +Optional properties :
> +- st,needs-antiglitch-filter : The board design needs glitch suppression
> +  enabled to operate reliably.
> +- st,min-scl-pulse-width : The minimum valid SCL pulse width that is allowed
> +  through the deglitch circuit. In units of us.
> +- st,min-sda-pulse-width : The minimum valid SDA pulse width that is allowed
> +  through the deglitch circuit. In units of us.

I could imagine generic properties here, like
	i2c-min-scl-pulse-width-us
	i2c-min-sda-pulse-width-us

So, if those are used, you can deduce that the glitch filter is wanted.
@DT maintainers: Sounds OK?

> +
> +Examples :
> +
> +i2c0: i2c@fed40000 {
> +	compatible	= "st,comms-ssc-i2c";
> +	reg		= <0xfed40000 0x110>;
> +	interrupts	=  <GIC_SPI 187 IRQ_TYPE_EDGE_RISING>;
> +	clocks		= <&CLK_S_ICN_REG_0>;
> +	clock-names	= "ssc";
> +	clock-frequency = <400000>;
> +	pinctrl-names	= "default";
> +	pinctrl-0	= <&pinctrl_i2c0_default>;
> +	st,needs-antiglitch-filter;
> +	st,min-scl-pulse-width = 0;
> +	st,min-sda-pulse-width = 5;
> +};
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index cdcbd83..18ff129 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -776,6 +776,16 @@ config I2C_RCAR
>  	  This driver can also be built as a module.  If so, the module
>  	  will be called i2c-rcar.
>  
> +config I2C_ST
> +	tristate "STMicroelectronics SSC I2C support"
> +	depends on ARCH_STI
> +	help
> +	  Enable this option to add support for STMicroelectronics SoCs
> +	  hardware SSC (Synchronous Serial Controller) as an I2C controller.
> +
> +	  This driver can also be built as module. If so, the module
> +	  will be called i2c-st.
> +
>  comment "External I2C/SMBus adapter drivers"
>  
>  config I2C_DIOLAN_U2C
> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
> index d00997f..9ea5d422 100644
> --- a/drivers/i2c/busses/Makefile
> +++ b/drivers/i2c/busses/Makefile
> @@ -92,5 +92,6 @@ obj-$(CONFIG_I2C_PCA_ISA)	+= i2c-pca-isa.o
>  obj-$(CONFIG_I2C_SIBYTE)	+= i2c-sibyte.o
>  obj-$(CONFIG_SCx200_ACB)	+= scx200_acb.o
>  obj-$(CONFIG_SCx200_I2C)	+= scx200_i2c.o
> +obj-$(CONFIG_I2C_ST)		+= i2c-st.o

Please keep it sorted.

>  
>  ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG
> diff --git a/drivers/i2c/busses/i2c-st.c b/drivers/i2c/busses/i2c-st.c
> new file mode 100644
> index 0000000..7eb3be4
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-st.c
> @@ -0,0 +1,691 @@
> +/*
> + * Copyright (C) 2013 STMicroelectronics
> + *
> + * I2C master mode controller driver, used in STMicroelectronics devices.
> + *
> + * Author: Maxime Coquelin <maxime.coquelin@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2, as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/i2c.h>
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/err.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include "i2c-st.h"
> +
> +#define DRIVER_NAME "st-i2c"

Nit: use the string directly

> +
> +/* From I2C Specifications v0.5 */
> +static struct st_i2c_timings i2c_timings[] = {
> +	[I2C_MODE_STANDARD] = {
> +		.rate			= 100000,
> +		.rep_start_hold		= 4000,
> +		.rep_start_setup	= 4700,
> +		.start_hold		= 4000,
> +		.data_setup_time	= 250,
> +		.stop_setup_time	= 4000,
> +		.bus_free_time		= 4700,
> +	},
> +	[I2C_MODE_FAST] = {
> +		.rate			= 400000,
> +		.rep_start_hold		= 600,
> +		.rep_start_setup	= 600,
> +		.start_hold		= 600,
> +		.data_setup_time	= 100,
> +		.stop_setup_time	= 600,
> +		.bus_free_time		= 1300,
> +	},
> +};

I assume there is no formula to calc these values?

> +
> +static void st_i2c_flush_rx_fifo(struct st_i2c_dev *i2c_dev)
> +{
> +	int count, i;
> +
> +	/*
> +	 * Counter only counts up to 7 but fifo size is 8...
> +	 * When fifo is full, counter is 0 and RIR bit of status register is
> +	 * set
> +	 */
> +	if (readl(i2c_dev->base + SSC_STA) & SSC_STA_RIR)
> +		count = SSC_RXFIFO_SIZE;
> +	else
> +		count = readl(i2c_dev->base + SSC_RX_FSTAT) &
> +			SSC_RX_FSTAT_STATUS;
> +
> +	for (i = 0; i < count; i++)
> +		readl(i2c_dev->base + SSC_RBUF);
> +}
> +
> +static void st_i2c_soft_reset(struct st_i2c_dev *i2c_dev)
> +{
> +	/*
> +	 * FIFO needs to be emptied before reseting the IP,
> +	 * else the controller raises a BUSY error.
> +	 */
> +	st_i2c_flush_rx_fifo(i2c_dev);
> +
> +	st_i2c_set_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
> +	st_i2c_clr_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
> +}
> +
> +/**
> + * st_i2c_hw_config() - Prepare SSC block, calculate and apply tuning timings
> + * @i2c_dev: Controller's private data
> + */
> +static void st_i2c_hw_config(struct st_i2c_dev *i2c_dev)
> +{
> +	unsigned long rate;
> +	u32 val, ns_per_clk;
> +	struct st_i2c_timings *t = &i2c_timings[i2c_dev->mode];
> +
> +	st_i2c_soft_reset(i2c_dev);
> +
> +	val = SSC_CLR_REPSTRT | SSC_CLR_NACK | SSC_CLR_SSCARBL |
> +		SSC_CLR_SSCAAS | SSC_CLR_SSCSTOP;
> +	writel(val, i2c_dev->base + SSC_CLR);
> +
> +	/* SSC Control register setup */
> +	val = SSC_CTL_PO | SSC_CTL_PH | SSC_CTL_HB | SSC_CTL_DATA_WIDTH_9;
> +	writel(val, i2c_dev->base + SSC_CTL);
> +
> +	rate = clk_get_rate(i2c_dev->clk);
> +	ns_per_clk = 1000000000 / rate;
> +
> +	/* Baudrate */
> +	val = rate / (2 * t->rate);
> +	writel(val, i2c_dev->base + SSC_BRG);
> +
> +	/* Pre-scaler baudrate */
> +	writel(1, i2c_dev->base + SSC_PRE_SCALER_BRG);
> +
> +	/* Enable I2C mode */
> +	writel(SSC_I2C_I2CM, i2c_dev->base + SSC_I2C);
> +
> +	/* Repeated start hold time */
> +	val = t->rep_start_hold / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_REP_START_HOLD);
> +
> +	/* Repeated start set up time */
> +	val = t->rep_start_setup / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_REP_START_SETUP);
> +
> +	/* Start hold time */
> +	val = t->start_hold / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_START_HOLD);
> +
> +	/* Data set up time */
> +	val = t->data_setup_time / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_DATA_SETUP);
> +
> +	/* Stop set up time */
> +	val = t->stop_setup_time / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_STOP_SETUP);
> +
> +	/* Bus free time */
> +	val = t->bus_free_time / ns_per_clk;
> +	writel(val, i2c_dev->base + SSC_BUS_FREE);
> +
> +	/* Prescalers set up */
> +	val = rate / 10000000;
> +	writel(val, i2c_dev->base + SSC_PRSCALER);
> +	writel(val, i2c_dev->base + SSC_PRSCALER_DATAOUT);
> +
> +	/* Noise suppression witdh */
> +	val = i2c_dev->deglitch.scl_min_width_us * rate / 100000000;
> +	writel(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH);
> +
> +	/* Noise suppression max output data delay width */
> +	val = i2c_dev->deglitch.sda_min_width_us * rate / 100000000;
> +	writel(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH_DATAOUT);
> +
> +	return;

return can be skipped.

> +}
> +
> +static int st_i2c_wait_free_bus(struct st_i2c_dev *i2c_dev)
> +{
> +	u32 sta;
> +	int i;
> +
> +	for (i = 0; i < 10; i++) {
> +		sta = readl(i2c_dev->base + SSC_STA);
> +		if (!(sta & SSC_STA_BUSY))
> +			return 0;
> +
> +		usleep_range(2000, 4000);
> +	}
> +
> +	dev_err(i2c_dev->dev, "bus not free (status = 0x%08x)\n", sta);
> +
> +	return -EBUSY;
> +}
> +
> +/**
> + * st_i2c_write_tx_fifo() - Write a byte in the Tx FIFO
> + * @i2c_dev: Controller's private data
> + * @byte: Data to write in the Tx FIFO
> + */
> +static inline void st_i2c_write_tx_fifo(struct st_i2c_dev *i2c_dev, u8 byte)
> +{
> +	u16 tbuf = byte << 1;
> +
> +	writel(tbuf | 1, i2c_dev->base + SSC_TBUF);
> +}
> +
> +/**
> + * st_i2c_wr_fill_tx_fifo() - Fill the Tx FIFO in write mode
> + * @i2c_dev: Controller's private data
> + *
> + * This functions fills the Tx FIFO with I2C transfert buffer when
> + * in write mode.
> + */
> +static void st_i2c_wr_fill_tx_fifo(struct st_i2c_dev *i2c_dev)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 tx_fstat, sta;
> +	int i;
> +
> +	sta = readl(i2c_dev->base + SSC_STA);
> +	if (sta & SSC_STA_TX_FIFO_FULL)
> +		return;
> +
> +	tx_fstat = readl(i2c_dev->base + SSC_TX_FSTAT) & SSC_TX_FSTAT_STATUS;
> +
> +	if (c->count < (SSC_TXFIFO_SIZE - tx_fstat))
> +		i = c->count;
> +	else
> +		i = SSC_TXFIFO_SIZE - tx_fstat;
> +
> +	for (; i > 0; i--, c->count--, c->buf++)
> +		st_i2c_write_tx_fifo(i2c_dev, *c->buf);
> +}
> +
> +/**
> + * st_i2c_rd_fill_tx_fifo() - Fill the Tx FIFO in read mode
> + * @i2c_dev: Controller's private data
> + *
> + * This functions fills the Tx FIFO with fixed pattern when
> + * in read mode to trigger clock.
> + */
> +static void st_i2c_rd_fill_tx_fifo(struct st_i2c_dev *i2c_dev, int max)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 tx_fstat, sta;
> +	int i;
> +
> +	sta = readl(i2c_dev->base + SSC_STA);
> +	if (sta & SSC_STA_TX_FIFO_FULL)
> +		return;
> +
> +	tx_fstat = readl(i2c_dev->base + SSC_TX_FSTAT) & SSC_TX_FSTAT_STATUS;
> +
> +	if (max < (SSC_TXFIFO_SIZE - tx_fstat))
> +		i = max;
> +	else
> +		i = SSC_TXFIFO_SIZE - tx_fstat;
> +
> +	for (; i > 0; i--, c->xfered++)
> +		st_i2c_write_tx_fifo(i2c_dev, 0xff);
> +}
> +
> +static void st_i2c_read_rx_fifo(struct st_i2c_dev *i2c_dev)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 i, sta;
> +	u16 rbuf;
> +
> +	sta = readl(i2c_dev->base + SSC_STA);
> +	if (sta & SSC_STA_RIR) {
> +		i = SSC_RXFIFO_SIZE;
> +	} else {
> +		i = readl(i2c_dev->base + SSC_RX_FSTAT);
> +		i &= SSC_RX_FSTAT_STATUS;
> +	}
> +
> +	for (; (i > 0) && (c->count > 0); i--, c->count--) {
> +		rbuf = readl(i2c_dev->base + SSC_RBUF) >> 1;
> +		*c->buf++ = (u8)rbuf & 0xff;
> +	}
> +
> +	if (i) {
> +		dev_err(i2c_dev->dev, "Unexpected %d bytes in rx fifo\n", i);
> +		st_i2c_flush_rx_fifo(i2c_dev);
> +	}
> +}
> +
> +/**
> + * st_i2c_terminate_xfer() - Send either STOP or REPSTART condition
> + * @i2c_dev: Controller's private data
> + */
> +static void st_i2c_terminate_xfer(struct st_i2c_dev *i2c_dev)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +
> +	st_i2c_clr_bits(i2c_dev->base + SSC_IEN, SSC_IEN_TEEN);
> +	st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
> +
> +	if (c->stop) {
> +		st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_STOPEN);
> +		st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
> +	} else {
> +		st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_REPSTRTEN);
> +		st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_REPSTRTG);
> +	}
> +}
> +
> +/**
> + * st_i2c_handle_write() - Handle FIFO empty interrupt in case of write
> + * @i2c_dev: Controller's private data
> + */
> +static void st_i2c_handle_write(struct st_i2c_dev *i2c_dev)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +
> +	st_i2c_flush_rx_fifo(i2c_dev);
> +
> +	if (!c->count)
> +		/* End of xfer, send stop or repstart */
> +		st_i2c_terminate_xfer(i2c_dev);
> +	else
> +		st_i2c_wr_fill_tx_fifo(i2c_dev);
> +}
> +
> +/**
> + * st_i2c_handle_write() - Handle FIFO enmpty interrupt in case of read
> + * @i2c_dev: Controller's private data
> + */
> +static void st_i2c_handle_read(struct st_i2c_dev *i2c_dev)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 ien;
> +
> +	/* Trash the address read back */
> +	if (!c->xfered) {
> +		readl(i2c_dev->base + SSC_RBUF);
> +		st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_TXENB);
> +	} else
> +		st_i2c_read_rx_fifo(i2c_dev);
> +
> +	if (!c->count) {
> +		/* End of xfer, send stop or repstart */
> +		st_i2c_terminate_xfer(i2c_dev);
> +	} else if (c->count == 1) {
> +		/* Penultimate byte to xfer, disable ACK gen. */
> +		st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_ACKG);
> +
> +		/* Last received byte is to be handled by NACK interrupt */
> +		ien = SSC_IEN_NACKEN | SSC_IEN_ARBLEN;
> +		writel(ien, i2c_dev->base + SSC_IEN);
> +
> +		st_i2c_rd_fill_tx_fifo(i2c_dev, c->count);
> +	} else
> +		st_i2c_rd_fill_tx_fifo(i2c_dev, c->count - 1);
> +}
> +
> +/**
> + * st_i2c_isr() - Interrupt routine
> + * @irq: interrupt number
> + * @data: Controller's private data
> + */
> +static irqreturn_t st_i2c_isr(int irq, void *data)
> +{
> +	struct st_i2c_dev *i2c_dev = data;
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 sta, ien;
> +	int it;
> +
> +	ien = readl(i2c_dev->base + SSC_IEN);
> +	sta = readl(i2c_dev->base + SSC_STA);
> +
> +	/* Use __fls() to check error bits first */
> +	it = __fls(sta & ien);
> +	if (it < 0) {
> +		dev_dbg(i2c_dev->dev, "spurious it (sta=0x%04x, ien=0x%04x)\n",
> +				sta, ien);
> +		return IRQ_HANDLED;

IRQ_HANDLED? IRQ_NONE I'd think.

> +	}
> +
> +	switch (1 << it) {
> +	case SSC_STA_TE:
> +		if (c->addr & I2C_M_RD)
> +			st_i2c_handle_read(i2c_dev);
> +		else
> +			st_i2c_handle_write(i2c_dev);
> +		break;
> +
> +	case SSC_STA_STOP:
> +	case SSC_STA_REPSTRT:
> +		writel(0, i2c_dev->base + SSC_IEN);
> +		complete(&i2c_dev->complete);
> +		break;
> +
> +	case SSC_STA_NACK:
> +		writel(SSC_CLR_NACK, i2c_dev->base + SSC_CLR);
> +
> +		/* Last received byte handled by NACK interrupt */
> +		if ((c->addr & I2C_M_RD) && (c->count == 1) && (c->xfered)) {
> +			st_i2c_handle_read(i2c_dev);
> +			break;
> +		}
> +
> +		it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
> +		writel(it, i2c_dev->base + SSC_IEN);
> +
> +		st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
> +		c->result = -EIO;
> +		break;
> +
> +	case SSC_STA_ARBL:
> +		writel(SSC_CLR_SSCARBL, i2c_dev->base + SSC_CLR);
> +
> +		it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
> +		writel(it, i2c_dev->base + SSC_IEN);
> +
> +		st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
> +		c->result = -EIO;
> +		break;
> +
> +	default:
> +		dev_err(i2c_dev->dev,
> +				"it %d unhandled (sta=0x%04x)\n", it, sta);
> +	}
> +
> +	return IRQ_HANDLED;
> +}
> +
> +/**
> + * st_i2c_xfer_msg() - Transfer a single I2C message
> + * @i2c_dev: Controller's private data
> + * @msg: I2C message to transfer
> + * @is_first: first message of the sequence
> + * @is_last: last message of the sequence
> + */
> +static int st_i2c_xfer_msg(struct st_i2c_dev *i2c_dev, struct i2c_msg *msg,
> +			    bool is_first, bool is_last)
> +{
> +	struct st_i2c_client *c = &i2c_dev->client;
> +	u32 ctl, i2c, it;
> +	unsigned long timeout;
> +	int ret;
> +
> +	c->addr		= (u8)(msg->addr << 1);
> +	c->addr		|= (msg->flags & I2C_M_RD);
> +	c->buf		= msg->buf;
> +	c->count	= msg->len;
> +	c->xfered	= 0;
> +	c->result	= 0;
> +	c->stop		= is_last;
> +
> +	init_completion(&i2c_dev->complete);

INIT_COMPLETION here, and init_completion in probe.

> +
> +	ctl = SSC_CTL_EN | SSC_CTL_MS |	SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
> +	st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
> +
> +	i2c = SSC_I2C_TXENB;
> +	if (c->addr & I2C_M_RD)
> +		i2c |= SSC_I2C_ACKG;
> +	st_i2c_set_bits(i2c_dev->base + SSC_I2C, i2c);
> +
> +	/* Write slave address */
> +	st_i2c_write_tx_fifo(i2c_dev, c->addr);
> +
> +	/* Pre-fill Tx fifo with data in case of write */
> +	if (!(c->addr & I2C_M_RD))
> +		st_i2c_wr_fill_tx_fifo(i2c_dev);
> +
> +	it = SSC_IEN_NACKEN | SSC_IEN_TEEN | SSC_IEN_ARBLEN;
> +	writel(it, i2c_dev->base + SSC_IEN);
> +
> +	if (is_first) {
> +		ret = st_i2c_wait_free_bus(i2c_dev);
> +		if (ret)
> +			return ret;
> +
> +		st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
> +	}
> +
> +	timeout = wait_for_completion_timeout(&i2c_dev->complete,
> +			i2c_dev->adap.timeout);
> +	ret = c->result;
> +
> +	if (!timeout) {
> +		dev_err(i2c_dev->dev, "Write to slave 0x%x timed out\n",
> +				c->addr);
> +		ret = -ETIMEDOUT;
> +	}
> +
> +	i2c = SSC_I2C_STOPG | SSC_I2C_REPSTRTG;
> +	st_i2c_clr_bits(i2c_dev->base + SSC_I2C, i2c);
> +
> +	writel(SSC_CLR_SSCSTOP | SSC_CLR_REPSTRT, i2c_dev->base + SSC_CLR);
> +
> +	return ret;
> +}
> +
> +/**
> + * st_i2c_xfer() - Transfer a single I2C message
> + * @i2c_adap: Adapter pointer to the controller
> + * @msgs: Pointer to data to be written.
> + * @num: Number of messages to be executed
> + */
> +static int st_i2c_xfer(struct i2c_adapter *i2c_adap,
> +			struct i2c_msg msgs[], int num)
> +{
> +	struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
> +	bool last, first;
> +	int ret, i;
> +
> +	i2c_dev->busy = true;
> +
> +	ret = clk_prepare_enable(i2c_dev->clk);
> +	if (ret) {
> +		dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
> +		return ret;
> +	}
> +
> +	pinctrl_pm_select_default_state(i2c_dev->dev);
> +
> +	st_i2c_hw_config(i2c_dev);
> +
> +	first = true;
> +
> +	for (i = 0; i < num; i++) {
> +		last = (i < num - 1) ? false : true;
> +
> +		ret = st_i2c_xfer_msg(i2c_dev, &msgs[i], first, last);

Simplify to:
ret = st_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0, i == num - 1) ?

> +		if (ret)
> +			break;
> +
> +		first = false;
> +	}
> +
> +	pinctrl_pm_select_idle_state(i2c_dev->dev);
> +
> +	clk_disable_unprepare(i2c_dev->clk);
> +
> +	i2c_dev->busy = false;
> +
> +	return (ret < 0) ? ret : i;
> +}
> +
> +#ifdef CONFIG_PM

CONFIG_PM_SLEEP

> +static int st_i2c_suspend(struct device *dev)
> +{
> +	struct platform_device *pdev =
> +		container_of(dev, struct platform_device, dev);
> +	struct st_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
> +
> +	if (i2c_dev->busy)
> +		return -EBUSY;
> +
> +	pinctrl_pm_select_sleep_state(dev);
> +
> +	return 0;
> +}
> +
> +static int st_i2c_resume(struct device *dev)
> +{
> +	pinctrl_pm_select_default_state(dev);
> +	/* Go in idle state if available */
> +	pinctrl_pm_select_idle_state(dev);
> +
> +	return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(st_i2c_pm, st_i2c_suspend, st_i2c_resume);
> +#define ST_I2C_PM	(&st_i2c_pm)
> +#else
> +#define ST_I2C_PM	NULL
> +#endif
> +
> +static u32 st_i2c_func(struct i2c_adapter *adap)
> +{
> +	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
> +}

Have you verified that SMBUS_QUICK works? You can use i2cdetect to check
that in case you haven't already.

> +
> +static struct i2c_algorithm st_i2c_algo = {
> +	.master_xfer = st_i2c_xfer,
> +	.functionality = st_i2c_func,
> +};
> +
> +static int st_i2c_of_get_deglitch(struct device_node *np,
> +		struct st_i2c_dev *i2c_dev)
> +{
> +	int ret;
> +
> +	if (!of_property_read_bool(np, "st,needs-antiglitch-filter"))
> +		return 0;
> +
> +	ret = of_property_read_u32(np, "st,min-scl-pulse-width",
> +			&i2c_dev->deglitch.scl_min_width_us);
> +	if (ret) {
> +		dev_err(i2c_dev->dev, "st,min-scl-pulse-width not found\n");
> +		return ret;
> +	}
> +
> +	ret = of_property_read_u32(np, "st,min-sda-pulse-width",
> +			&i2c_dev->deglitch.sda_min_width_us);
> +	if (ret) {
> +		dev_err(i2c_dev->dev, "st,min-sda-pulse-width not found\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int st_i2c_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct st_i2c_dev *i2c_dev;
> +	struct resource *res;
> +	u32 clk_rate;
> +	struct i2c_adapter *adap;
> +	int ret;
> +
> +	i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
> +	if (!i2c_dev)
> +		return -ENOMEM;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	i2c_dev->base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(i2c_dev->base))
> +		return PTR_ERR(i2c_dev->base);
> +
> +	i2c_dev->irq = irq_of_parse_and_map(np, 0);
> +	if (!i2c_dev->irq) {
> +		dev_err(&pdev->dev, "IRQ missing or invalid\n");
> +		return -EINVAL;
> +	}
> +
> +	i2c_dev->clk = of_clk_get_by_name(np, "ssc");
> +	if (IS_ERR(i2c_dev->clk)) {
> +		dev_err(&pdev->dev, "Unable to request clock\n");
> +		return PTR_ERR(i2c_dev->clk);
> +	}
> +
> +	i2c_dev->mode = I2C_MODE_STANDARD;
> +	ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
> +	if ((!ret) && (clk_rate == 400000))
> +		i2c_dev->mode = I2C_MODE_FAST;
> +
> +	i2c_dev->dev = &pdev->dev;
> +
> +	ret = devm_request_irq(&pdev->dev, i2c_dev->irq, st_i2c_isr, 0,
> +			pdev->name, i2c_dev);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Failed to request irq %i\n", i2c_dev->irq);
> +		return ret;
> +	}
> +
> +	pinctrl_pm_select_default_state(i2c_dev->dev);
> +	/* In case idle state available, select it */
> +	pinctrl_pm_select_idle_state(i2c_dev->dev);
> +
> +	ret = st_i2c_of_get_deglitch(np, i2c_dev);
> +	if (ret)
> +		return ret;
> +
> +	adap = &i2c_dev->adap;
> +	i2c_set_adapdata(adap, i2c_dev);
> +	snprintf(adap->name, sizeof(adap->name), "ST I2C(0x%08x)", res->start);
> +	adap->owner = THIS_MODULE;
> +	adap->timeout = 2 * HZ;
> +	adap->retries = 0;
> +	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DDC | I2C_CLASS_SPD;

Why do you need class based instantiation. It will most likely cost
boot-time and you have devicetree means for doing instantiation.

> +	adap->algo = &st_i2c_algo;
> +	adap->dev.parent = &pdev->dev;
> +	adap->dev.of_node = pdev->dev.of_node;
> +
> +	ret = i2c_add_adapter(adap);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Failed to add adapter\n");
> +		return ret;
> +	}
> +
> +	platform_set_drvdata(pdev, i2c_dev);
> +
> +	dev_info(i2c_dev->dev, "%s initialized\n", adap->name);
> +
> +	return 0;
> +}
> +
> +static int st_i2c_remove(struct platform_device *pdev)
> +{
> +	struct st_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
> +
> +	i2c_del_adapter(&i2c_dev->adap);
> +
> +	return 0;
> +}
> +
> +static struct of_device_id st_i2c_match[] = {
> +	{ .compatible = "st,comms-ssc-i2c", },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, st_i2c_match);
> +
> +static struct platform_driver st_i2c_driver = {
> +	.driver = {
> +		.name = DRIVER_NAME,
> +		.owner = THIS_MODULE,
> +		.of_match_table = st_i2c_match,
> +		.pm = &st_i2c_pm,

You probably wanted ST_I2C_PM here?

> +	},
> +	.probe = st_i2c_probe,
> +	.remove = st_i2c_remove,
> +};
> +
> +module_platform_driver(st_i2c_driver);
> +
> +MODULE_AUTHOR("STMicroelectronics");

I'd prefer your name, but at least, we need an email address.

> +MODULE_DESCRIPTION("STMicroelectronics I2C driver");
> +MODULE_LICENSE("GPL");

Header says GPL v2.

> diff --git a/drivers/i2c/busses/i2c-st.h b/drivers/i2c/busses/i2c-st.h
> new file mode 100644
> index 0000000..e8ba3dc
> --- /dev/null
> +++ b/drivers/i2c/busses/i2c-st.h
> @@ -0,0 +1,208 @@

Since this is not shared, please include into the c-file.

> +/*
> + * Copyright (C) 2013 STMicroelectronics
> + *
> + * I2C master mode controller driver, used in STMicroelectronics devices.
> + *
> + * Author: Maxime Coquelin <maxime.coquelin@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2, as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef __I2C_ST_H_
> +#define __I2C_ST_H_
> +
> +/* SSC registers */
> +#define SSC_BRG				0x000
> +#define SSC_TBUF			0x004
> +#define SSC_RBUF			0x008
> +#define SSC_CTL				0x00C
> +#define SSC_IEN				0x010
> +#define SSC_STA				0x014
> +#define SSC_I2C				0x018
> +#define SSC_SLAD			0x01C
> +#define SSC_REP_START_HOLD		0x020
> +#define SSC_START_HOLD			0x024
> +#define SSC_REP_START_SETUP		0x028
> +#define SSC_DATA_SETUP			0x02C
> +#define SSC_STOP_SETUP			0x030
> +#define SSC_BUS_FREE			0x034
> +#define SSC_TX_FSTAT			0x038
> +#define SSC_RX_FSTAT			0x03C
> +#define SSC_PRE_SCALER_BRG		0x040
> +#define SSC_CLR				0x080
> +#define SSC_NOISE_SUPP_WIDTH		0x100
> +#define SSC_PRSCALER			0x104
> +#define SSC_NOISE_SUPP_WIDTH_DATAOUT	0x108
> +#define SSC_PRSCALER_DATAOUT		0x10c
> +
> +/* SSC Control */
> +#define SSC_CTL_DATA_WIDTH_9		0x8
> +#define SSC_CTL_DATA_WIDTH_MSK		0xf
> +#define SSC_CTL_BM			0xf
> +#define SSC_CTL_HB			BIT(4)
> +#define SSC_CTL_PH			BIT(5)
> +#define SSC_CTL_PO			BIT(6)
> +#define SSC_CTL_SR			BIT(7)
> +#define SSC_CTL_MS			BIT(8)
> +#define SSC_CTL_EN			BIT(9)
> +#define SSC_CTL_LPB			BIT(10)
> +#define SSC_CTL_EN_TX_FIFO		BIT(11)
> +#define SSC_CTL_EN_RX_FIFO		BIT(12)
> +#define SSC_CTL_EN_CLST_RX		BIT(13)
> +
> +/* SSC Interrupt Enable */
> +#define SSC_IEN_RIEN			BIT(0)
> +#define SSC_IEN_TIEN			BIT(1)
> +#define SSC_IEN_TEEN			BIT(2)
> +#define SSC_IEN_REEN			BIT(3)
> +#define SSC_IEN_PEEN			BIT(4)
> +#define SSC_IEN_AASEN			BIT(6)
> +#define SSC_IEN_STOPEN			BIT(7)
> +#define SSC_IEN_ARBLEN			BIT(8)
> +#define SSC_IEN_NACKEN			BIT(10)
> +#define SSC_IEN_REPSTRTEN		BIT(11)
> +#define SSC_IEN_TX_FIFO_HALF		BIT(12)
> +#define SSC_IEN_RX_FIFO_HALF_FULL	BIT(14)
> +
> +/* SSC Status */
> +#define SSC_STA_RIR			BIT(0)
> +#define SSC_STA_TIR			BIT(1)
> +#define SSC_STA_TE			BIT(2)
> +#define SSC_STA_RE			BIT(3)
> +#define SSC_STA_PE			BIT(4)
> +#define SSC_STA_CLST			BIT(5)
> +#define SSC_STA_AAS			BIT(6)
> +#define SSC_STA_STOP			BIT(7)
> +#define SSC_STA_ARBL			BIT(8)
> +#define SSC_STA_BUSY			BIT(9)
> +#define SSC_STA_NACK			BIT(10)
> +#define SSC_STA_REPSTRT			BIT(11)
> +#define SSC_STA_TX_FIFO_HALF		BIT(12)
> +#define SSC_STA_TX_FIFO_FULL		BIT(13)
> +#define SSC_STA_RX_FIFO_HALF		BIT(14)
> +
> +/* SSC I2C Control */
> +#define SSC_I2C_I2CM			BIT(0)
> +#define SSC_I2C_STRTG			BIT(1)
> +#define SSC_I2C_STOPG			BIT(2)
> +#define SSC_I2C_ACKG			BIT(3)
> +#define SSC_I2C_AD10			BIT(4)
> +#define SSC_I2C_TXENB			BIT(5)
> +#define SSC_I2C_REPSTRTG		BIT(11)
> +#define SSC_I2C_SLAVE_DISABLE		BIT(12)
> +
> +/* SSC Tx FIFO Status */
> +#define SSC_TX_FSTAT_STATUS		0x07
> +
> +/* SSC Rx FIFO Status */
> +#define SSC_RX_FSTAT_STATUS		0x07
> +
> +/* SSC Clear bit operation */
> +#define SSC_CLR_SSCAAS			BIT(6)
> +#define SSC_CLR_SSCSTOP			BIT(7)
> +#define SSC_CLR_SSCARBL			BIT(8)
> +#define SSC_CLR_NACK			BIT(10)
> +#define SSC_CLR_REPSTRT			BIT(11)
> +
> +/* SSC Clock Prescaler */
> +#define SSC_PRSC_VALUE			0x0f
> +
> +
> +#define SSC_TXFIFO_SIZE			0x8
> +#define SSC_RXFIFO_SIZE			0x8
> +
> +enum st_i2c_mode {
> +	I2C_MODE_STANDARD,
> +	I2C_MODE_FAST,
> +	I2C_MODE_END,
> +};
> +
> +/**
> + * struct st_i2c_timings - per-Mode tuning parameters
> + * @rate: I2C bus rate
> + * @rep_start_hold: I2C repeated start hold time requirement
> + * @rep_start_setup: I2C repeated start set up time requirement
> + * @start_hold: I2C start hold time requirement
> + * @data_setup_time: I2C data set up time requirement
> + * @stop_setup_time: I2C stop set up time requirement
> + * @bus_free_time: I2C bus free time requirement
> + * @sda_pulse_min_limit: I2C SDA pulse mini width limit
> + */
> +struct st_i2c_timings {
> +	u32 rate;
> +	u32 rep_start_hold;
> +	u32 rep_start_setup;
> +	u32 start_hold;
> +	u32 data_setup_time;
> +	u32 stop_setup_time;
> +	u32 bus_free_time;
> +	u32 sda_pulse_min_limit;
> +};
> +
> +/**
> + * struct st_i2c_deglitch - Anti-glitch filter configuration
> + * @scl_min_width_us: SCL line minimum pulse width in ns
> + * @sda_min_width_us: SDA line minimum pulse width in ns
> + */
> +struct st_i2c_deglitch {
> +	u32	scl_min_width_us;
> +	u32	sda_min_width_us;
> +};
> +
> +/**
> + * struct st_i2c_client - client specific data
> + * @addr: 8-bit slave addr, including r/w bit
> + * @count: number of bytes to be transfered
> + * @xfered: number of bytes already transferred
> + * @buf: data buffer
> + * @result: result of the transfer
> + * @stop: last I2C msg to be sent, i.e. STOP to be generated
> + */
> +struct st_i2c_client {
> +	u8	addr;
> +	u32	count;
> +	u32	xfered;
> +	u8	*buf;
> +	int	result;
> +	bool	stop;
> +};
> +
> +/**
> + * struct st_i2c_dev - private data of the controller
> + * @adap: I2C adapter for this controller
> + * @dev: device for this controller
> + * @base: virtual memory area
> + * @complete: completion of I2C message
> + * @irq: interrupt line for th controller
> + * @clk: hw ssc block clock
> + * @mode: I2C mode of the controller. Standard or Fast only supported
> + * @deglitch: Anti-glitch filters parameters
> + * @client: I2C transfert information
> + * @busy: I2C transfer on-going
> + */
> +struct st_i2c_dev {
> +	struct i2c_adapter	adap;
> +	struct device		*dev;
> +	void __iomem		*base;
> +	struct completion	complete;
> +	int			irq;
> +	struct clk		*clk;
> +	int			mode;
> +	struct st_i2c_deglitch	deglitch;
> +	struct st_i2c_client	client;
> +	bool			busy;
> +};
> +
> +static inline void st_i2c_set_bits(void __iomem *reg, u32 mask)
> +{
> +	writel(readl(reg) | mask, reg);
> +}
> +
> +static inline void st_i2c_clr_bits(void __iomem *reg, u32 mask)
> +{
> +	writel(readl(reg) & ~mask, reg);
> +}
> +
> +#endif /* __I2C_ST_H_ */
> -- 
> 1.7.9.5
> 

Thanks,

   Wolfram

Attachment: signature.asc
Description: Digital signature


[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux