On Mon, Sep 23, 2013 at 08:31:48PM +0100, Felipe Balbi wrote:
> Hi,
>
> On Tue, Aug 20, 2013 at 12:56:03PM +0300, Ivan T. Ivanov wrote:
> > From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx>
> >
> > MSM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
> > (SNPS) and HS, SS PHY's control and configuration registers.
> >
> > It could operate in device mode (SS, HS, FS) and host
> > mode (SS, HS, FS, LS).
> >
> > Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx>
>
> Any acks for the DT part ? This patch has been pending forever.
Apologies for the delay. I have a couple of comments that would be nice
to fix up now.
>
> > ---
> > .../devicetree/bindings/usb/msm-ssusb.txt | 104 ++++++++++++++++++++
> > 1 file changed, 104 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/usb/msm-ssusb.txt
> >
> > diff --git a/Documentation/devicetree/bindings/usb/msm-ssusb.txt b/Documentation/devicetree/bindings/usb/msm-ssusb.txt
> > new file mode 100644
> > index 0000000..cacbd3b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/msm-ssusb.txt
> > @@ -0,0 +1,104 @@
> > +MSM SuperSpeed DWC3 USB SoC controller
> > +
> > +
> > +DWC3 Highspeed USB PHY
> > +======================
> > +Required properities :
> > +- compatible : sould be "qcom,dwc3-hsphy";
s/sould/should/
In general, compatible properties are "should contain" rather than
"should be", as we might have backwards compatible hardware in future.
> > +- reg : offset and length of the register set in the memory map
> > +- clocks : phandles to clock instances of the device tree nodes
Clocks are referred to be phandle + clock-specifier pairs rather than
phandles, it would be nice to fix the terminology here
> > +- clock-names :
> > + "xo" : External reference clock 19 MHz
> > + "sleep_a" : Sleep clock, used when USB3 core goes into low
> > + power mode (U3).
I think it would be nicer to say:
- clocks : A list of phandle + clock-specifier pairs for the clocks
listed in clock-names
- clock-names: Should contain the following:
"xo" - External reference clock (19MHz)
"sleep_a" - Sleep clock used when USB3 core goes into low
power mode (U3).
I'm not sure we need to describe the frequency of the xo clock -- either
it's a requriement of the IP and thus doesn't need to be a part of the
binding, or it's configurable by the driver and thus doesn't need to be
documented.
> > +<supply-name>-supply : phandle to the regulator device tree node
> > +Required "supply-name" are:
> > + "v1p8" : 1.8v supply for HSPHY
> > + "v3p3" : 3.3v supply for HSPHY
> > + "vbus" : vbus supply for host mode
> > + "vddcx" : vdd supply for HS-PHY digital circuit operation
Any reason for the HSPHY/HS-PHY difference?
I'd list these separately with their full names:
- v1p8-supply: phandle to the regulator for the 1.8v supply to HSPHY.
- v3p3-supply: phandle to the regulator for the 3.3v supply to HSPHY.
- vbus-supply: phandle to the regulator for the vbus supply for host
mode.
- vddcx-supply: phandle to the regulator for the vdd supply for HSPHY
digital circuit operation.
> > +
> > +DWC3 Superspeed USB PHY
> > +=======================
> > +Required properities :
> > +- compatible : sould be "qcom,dwc3-ssphy";
> > +- reg : offset and length of the register set in the memory map
> > +- clocks : phandles to clock instances of the device tree nodes
> > +- clock-names :
> > + "xo" : External reference clock 19 MHz
> > + "ref" : Reference clock - used in host mode.
> > +<supply-name>-supply : phandle to the regulator device tree node
> > +Required "supply-name" are:
> > + "v1p8" : 1.8v supply for SS-PHY
> > + "vddcx" : vdd supply for SS-PHY digital circuit operation
The commments on compatible, clocks, clock-names and the regulators
apply here.
> > +
> > +DWC3 controller wrapper
> > +=======================
> > +Required properties :
> > +- compatible : should be "qcom,dwc3"
> > +- reg : offset and length of the register set in the memory map
> > + offset and length of the TCSR register for routing USB
> > + signals to either picoPHY0 or picoPHY1.
> > +- clocks : phandles to clock instances of the device tree nodes
> > +- clock-names :
> > + "core" : Master/Core clock, have to be >= 125 MHz for SS
> > + operation and >= 60MHz for HS operation
> > + "iface" : System bus AXI clock
> > + "sleep" : Sleep clock, used when USB3 core goes into low
> > + power mode (U3).
> > + "utmi" : Generated by HS-PHY. Used to clock the low power
> > + parts of thr HS Link layer.
> > +Optional properties :
> > +- gdsc-supply : phandle to the globally distributed switch controller
> > + regulator node to the USB controller.
The commments on compatible, clocks, and clock-names apply here too. I
see the regulator is defined individually :)
I'm fine with the binding itself, I'd just like the documentation fixed
up.
Cheers,
Mark.
> > +Required child node:
> > +A child node must exist to represent the core DWC3 IP block. The name of
> > +the node is not important. The content of the node is defined in dwc3.txt.
> > +
> > +Example device nodes:
> > +
> > + dwc3_hsphy: phy@f92f8800 {
> > + compatible = "qcom,dwc3-hsphy";
> > + reg = <0xf92f8800 0x30>;
> > +
> > + clocks = <&cxo>, <&usb2a_phy_sleep_cxc>;
> > + clock-names = "xo", "sleep_a";
> > +
> > + vbus-supply = <&supply>;
> > + vddcx-supply = <&supply>;
> > + v1p8-supply = <&supply>;
> > + v3p3-supply = <&supply>;
> > + };
> > +
> > + dwc3_ssphy: phy@f92f8830 {
> > + compatible = "qcom,dwc3-ssphy";
> > + reg = <0xf92f8830 0x30>;
> > +
> > + clocks = <&cxo>, <&usb30_mock_utmi_cxc>;
> > + clock-names = "xo", "ref";
> > +
> > + vddcx-supply = <&supply>;
> > + v1p8-supply = <&supply>;
> > + };
> > +
> > + usb@fd4ab000 {
> > + compatible = "qcom,dwc3";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + reg = <0xfd4ab000 0x4>;
> > +
> > + clocks = <&usb30_master_cxc>, <&sys_noc_usb3_axi_cxc>,
> > + <&usb30_sleep_cxc>, <&usb30_mock_utmi_cxc>;
> > + clock-names = "core", "iface", "sleep", "utmi";
> > +
> > + gdsc-supply = <&supply>;
> > +
> > + ranges;
> > + dwc3@f9200000 {
> > + compatible = "snps,dwc3";
> > + reg = <0xf9200000 0xcd00>;
> > + interrupts = <0 131 0>;
> > + usb-phy = <&dwc3_hsphy>, <&dwc3_ssphy>;
> > + tx-fifo-resize;
> > + };
> > + };
> > --
> > 1.7.9.5
> >
>
> --
> balbi
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
