This patch adds basic DT bindings for the PL11x CLCD cells
and make their fbdev driver use them.
Signed-off-by: Pawel Moll <pawel.moll@xxxxxxx>
---
Changes since v3:
- changed wording and order of interrupt-names and interrupts
properties documentation
- changed wording of arm,pl11x,framebuffer-base property
documentation
- cleaned up binding documentation indentation
Changes since v2:
- replaced video-ram phandle with arm,pl11x,framebuffer-base
- replaced panel-* properties with arm,pl11x,panel-data-pads
- replaced max-framebuffer-size with max-memory-bandwidth
- modified clcdfb_of_init_tft_panel() to use the pads
data and take differences between PL110 and PL110 into
account
Changes since v1:
- minor code cleanups as suggested by Sylwester Nawrocki
.../devicetree/bindings/video/arm,pl11x.txt | 145 +++++++++++
.../devicetree/bindings/video/arm,pl11x.txt | 146 +++++++++++
drivers/video/Kconfig | 1 +
drivers/video/amba-clcd.c | 268 +++++++++++++++++++++
3 files changed, 415 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/arm,pl11x.txt
diff --git a/Documentation/devicetree/bindings/video/arm,pl11x.txt b/Documentation/devicetree/bindings/video/arm,pl11x.txt
new file mode 100644
index 0000000..247e120
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/arm,pl11x.txt
@@ -0,0 +1,146 @@
+* ARM PrimeCell Color LCD Controller PL110/PL111
+
+See also Documentation/devicetree/bindings/arm/primecell.txt
+
+Required properties:
+
+- compatible: must be one of:
+ "arm,pl110", "arm,primecell"
+ "arm,pl111", "arm,primecell"
+
+- reg: base address and size of the control registers block
+
+- interrupt-names: either the single entry "combined" representing a
+ combined interrupt output (CLCDINTR), or the four entries
+ "mbe", "vcomp", "lnbu", "fuf" representing the individual
+ CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
+
+- interrupts: contains an interrupt specifier for each entry in
+ interrupt-names
+
+- clocks names: should contain "clcdclk" and "apb_pclk"
+
+- clocks: contains phandle and clock specifier pairs for the entries
+ in the clock-names property. See
+ Documentation/devicetree/binding/clock/clock-bindings.txt
+
+- arm,pl11x,panel-data-pads: array of 24 cells, each of them describing
+ a function of one of the CLD pads, starting from 0 up to 23;
+ each pad can be described by one of the following values:
+ - 0: reserved (not connected)
+ - 0x100-0x107: color upper STN panel data 0 to 7
+ - 0x110-0x117: color lower STN panel data 0 to 7
+ - 0x200-0x207: mono upper STN panel data 0 to 7
+ - 0x210-0x217: mono lower STN panel data 0 to 7
+ - 0x300-0x307: red component bit 0 to 7 of TFT panel data
+ - 0x310-0x317: green component bit 0 to 7 of TFT panel data
+ - 0x320-0x327: blue component bit 0 to 7 of TFT panel data
+ - 0x330: intensity bit of TFT panel data
+ Example sets of values for standard panel interfaces:
+ - PL110 single colour STN panel:
+ <0x107 0x106 0x105 0x104 0x103 0x102 0x101 0x100>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL110 dual colour STN panel:
+ <0x107 0x106 0x105 0x104 0x103 0x102 0x101 0x100>,
+ <0x117 0x116 0x115 0x114 0x113 0x112 0x111 0x110>,
+ <0 0 0 0 0 0 0 0>;
+ - PL110 single mono 4-bit STN panel:
+ <0x203 0x202 0x201 0x200>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL110 dual mono 4-bit STN panel:
+ <0x203 0x202 0x201 0x200>, <0 0 0 0>,
+ <0x213 0x212 0x211 0x210>,
+ <0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL110 single mono 8-bit STN panel:
+ <0x207 0x206 0x205 0x204 0x203 0x202 0x201 0x200>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL110 dual mono 8-bit STN panel:
+ <0x207 0x206 0x205 0x204 0x203 0x202 0x201 0x200>,
+ <0x217 0x216 0x215 0x214 0x213 0x212 0x211 0x210>,
+ <0 0 0 0 0 0 0 0>;
+ - PL110 TFT (1:)5:5:5 panel:
+ <0x330 0x300 0x301 0x302 0x303 0x304>,
+ <0x330 0x310 0x311 0x312 0x313 0x314>,
+ <0x330 0x320 0x321 0x322 0x323 0x324>,
+ <0 0 0 0 0 0>
+ - PL110 and PL111 TFT RGB 888 panel:
+ <0x300 0x301 0x302 0x303 0x304 0x305 0x306 0x307>,
+ <0x310 0x311 0x312 0x313 0x314 0x315 0x316 0x317>,
+ <0x320 0x321 0x322 0x323 0x324 0x325 0x326 0x327>;
+ - PL111 single colour STN panel:
+ <0x100 0x101 0x102 0x103 0x104 0x105 0x106 0x107>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL111 dual colour STN panel:
+ <0x100 0x101 0x102 0x103 0x104 0x105 0x106 0x107>,
+ <0x110 0x111 0x112 0x113 0x114 0x115 0x116 0x117>,
+ <0 0 0 0 0 0 0 0>;
+ - PL111 single mono 4-bit STN panel:
+ <0x200 0x201 0x202 0x203>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL111 dual mono 4-bit STN panel:
+ <0x200 0x201 0x202 0x203>, <0 0 0 0>,
+ <0x210 0x211 0x212 0x213>,
+ <0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL111 single mono 8-bit STN panel:
+ <0x200 0x201 0x202 0x203 0x204 0x205 0x206 0x207>,
+ <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
+ - PL111 dual mono 8-bit STN panel:
+ <0x200 0x201 0x202 0x203 0x204 0x205 0x206 0x207>,
+ <0x210 0x211 0x212 0x213 0x214 0x215 0x216 0x217>,
+ <0 0 0 0 0 0 0 0>;
+ - PL111 TFT 4:4:4 panel:
+ <0 0 0 0>, <0x300 0x301 0x302 0x303>,
+ <0 0 0 0>, <0x310 0x311 0x312 0x313>,
+ <0 0 0 0>, <0x320 0x321 0x322 0x323>;
+ - PL111 TFT 5:6:5 panel:
+ <0 0 0>, <0x300 0x301 0x302 0x303 0x304>,
+ <0 0>, <0x310 0x311 0x312 0x313 0x314 0x315>,
+ <0 0 0>, <0x320 0x321 0x322 0x323 0x324>;
+ - PL111 TFT (1):5:5:5 panel:
+ <0 0 0>, <0x300 0x301 0x302 0x303 0x304>,
+ <0 0>, <0x330 0x310 0x311 0x312 0x313 0x314>,
+ <0 0 0>, <0x320 0x321 0x322 0x323 0x324>;
+
+Optional properties:
+
+- arm,pl11x,framebuffer-base: a pair of two values, address and size,
+ defining the framebuffer that must be used; if not present, the
+ framebuffer may be located anywhere in the memory
+
+- max-memory-bandwidth: maximum bandwidth in bytes per second that the
+ cell's memory interface can handle
+
+- display-timings: standard display timings sub-node, defining possible
+ video modes of a connected panel; for details see
+ Documentation/devicetree/bindings/video/display-timing.txt
+
+Example:
+
+ clcd@1f0000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x1f0000 0x1000>;
+ interrupt-names = "combined";
+ interrupts = <14>;
+ clock-names = "clcdclk", "apb_pclk";
+ clocks = <&v2m_oscclk1>, <&smbclk>;
+
+ arm,pl11x,panel-data-pads = <0x300 0x301 0x302 0x303 0x304 0x305 0x306 0x307>,
+ <0x310 0x311 0x312 0x313 0x314 0x315 0x316 0x317>,
+ <0x320 0x321 0x322 0x323 0x324 0x325 0x326 0x327>;
+ arm,pl11x,framebuffer-base = <0x18000000 0x00800000>;
+ max-memory-bandwidth = <36864000>; /* bps, 640x480@60 16bpp */
+ display-timings {
+ native-mode = <&v2m_clcd_timing0>;
+ v2m_clcd_timing0: vga {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ hback-porch = <40>;
+ hfront-porch = <24>;
+ hsync-len = <96>;
+ vactive = <480>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <2>;
+ };
+ };
+ };
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 84b685f..b7d8c23 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -316,6 +316,7 @@ config FB_ARMCLCD
select FB_CFB_FILLRECT
select FB_CFB_COPYAREA
select FB_CFB_IMAGEBLIT
+ select VIDEOMODE_HELPERS if OF
help
This framebuffer device driver is for the ARM PrimeCell PL110
Colour LCD controller. ARM PrimeCells provide the building
diff --git a/drivers/video/amba-clcd.c b/drivers/video/amba-clcd.c
index 0a2cce7..03420d1 100644
--- a/drivers/video/amba-clcd.c
+++ b/drivers/video/amba-clcd.c
@@ -25,6 +25,11 @@
#include <linux/amba/clcd.h>
#include <linux/clk.h>
#include <linux/hardirq.h>
+#include <linux/dma-mapping.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <video/of_display_timing.h>
+#include <video/of_videomode.h>
#include <asm/sizes.h>
@@ -542,6 +547,266 @@ static int clcdfb_register(struct clcd_fb *fb)
return ret;
}
+#ifdef CONFIG_OF
+
+#define CLCD_PADS_NUM 24
+
+#define CLCD_PAD_BIT(pad) ((pad) & 0xf)
+#define CLCD_PAD_TYPE(pad) (((pad) >> 8) & 0xf)
+
+#define CLCD_PAD_IS_TFT(pad) (CLCD_PAD_TYPE(pad) == 0x3)
+
+#define CLCD_PAD_RGB(pad) (((pad) >> 4) & 0xf)
+#define CLCD_PAD_R 0x0
+#define CLCD_PAD_G 0x1
+#define CLCD_PAD_B 0x2
+
+static int clcdfb_of_init_tft_panel(struct clcd_fb *fb, u32 *pads)
+{
+ static struct {
+ unsigned int part;
+ int r0, g0, b0;
+ u32 caps;
+ } panels[] = {
+ { 0x110, 1, 7, 13, CLCD_CAP_5551 },
+ { 0x110, 0, 8, 16, CLCD_CAP_888 },
+ { 0x111, 4, 14, 20, CLCD_CAP_444 },
+ { 0x111, 3, 11, 19, CLCD_CAP_444 | CLCD_CAP_5551 },
+ { 0x111, 3, 10, 19, CLCD_CAP_444 | CLCD_CAP_5551 |
+ CLCD_CAP_565 },
+ { 0x111, 0, 8, 16, CLCD_CAP_444 | CLCD_CAP_5551 |
+ CLCD_CAP_565 | CLCD_CAP_888 },
+ };
+ int r = 0, g = 0, b = 0;
+ int r0 = -1, g0 = -1, b0 = -1;
+ int i;
+
+ /* Bypass pixel clock divider, data output on the falling edge */
+ fb->panel->tim2 = TIM2_BCD | TIM2_IPC;
+
+ /* TFT display, vert. comp. interrupt at the start of the back porch */
+ fb->panel->cntl |= CNTL_LCDTFT | CNTL_LCDVCOMP(1);
+
+ fb->panel->caps = 0;
+
+ /*
+ * Find indices of the first component bits and make sure they
+ * are in correct order
+ */
+ for (i = 0; i < CLCD_PADS_NUM; i++) {
+ int bit;
+
+ if (!pads[i])
+ continue;
+ switch (CLCD_PAD_RGB(pads[i])) {
+ case CLCD_PAD_R:
+ r0 = r ? r0 : i;
+ bit = r++;
+ break;
+ case CLCD_PAD_G:
+ g0 = g ? g0 : i;
+ bit = g++;
+ break;
+ case CLCD_PAD_B:
+ b0 = b ? b0 : i;
+ bit = b++;
+ break;
+ default:
+ return -EINVAL;
+ }
+ if (bit != CLCD_PAD_BIT(pads[i]) || !CLCD_PAD_IS_TFT(pads[i]))
+ return -EINVAL;
+ }
+
+ /* Match the setup with known variants */
+ for (i = 0; i < ARRAY_SIZE(panels) && !fb->panel->caps; i++) {
+ if (amba_part(fb->dev) != panels[i].part)
+ continue;
+ if (g0 != panels[i].g0)
+ continue;
+ if (r0 == panels[i].r0 && b0 == panels[i].b0)
+ fb->panel->caps = panels[i].caps & CLCD_CAP_RGB;
+ if (r0 == panels[i].b0 && b0 == panels[i].r0)
+ fb->panel->caps = panels[i].caps & CLCD_CAP_BGR;
+ }
+
+ return fb->panel->caps ? 0 : -EINVAL;
+}
+
+static int clcdfb_snprintf_mode(char *buf, int size, struct fb_videomode *mode)
+{
+ return snprintf(buf, size, "%ux%u@%u", mode->xres, mode->yres,
+ mode->refresh);
+}
+
+static int clcdfb_of_init_display(struct clcd_fb *fb)
+{
+ struct device_node *node = fb->dev->dev.of_node;
+ int err, len;
+ char *mode_name;
+ u32 max_bandwidth;
+ u32 pads[CLCD_PADS_NUM];
+ int i;
+
+ fb->panel = devm_kzalloc(&fb->dev->dev, sizeof(*fb->panel), GFP_KERNEL);
+ if (!fb->panel)
+ return -ENOMEM;
+
+ err = of_get_fb_videomode(node, &fb->panel->mode, OF_USE_NATIVE_MODE);
+ if (err)
+ return err;
+
+ len = clcdfb_snprintf_mode(NULL, 0, &fb->panel->mode);
+ mode_name = devm_kzalloc(&fb->dev->dev, len + 1, GFP_KERNEL);
+ clcdfb_snprintf_mode(mode_name, len + 1, &fb->panel->mode);
+ fb->panel->mode.name = mode_name;
+
+ err = of_property_read_u32(node, "max-memory-bandwidth",
+ &max_bandwidth);
+ if (!err)
+ fb->panel->bpp = 8 * max_bandwidth / (fb->panel->mode.xres *
+ fb->panel->mode.yres * fb->panel->mode.refresh);
+ else
+ fb->panel->bpp = 32;
+
+#ifdef CONFIG_CPU_BIG_ENDIAN
+ fb->panel->cntl |= CNTL_BEBO;
+#endif
+ fb->panel->width = -1;
+ fb->panel->height = -1;
+
+ err = of_property_read_u32_array(node, "arm,pl11x,panel-data-pads",
+ pads, ARRAY_SIZE(pads));
+ if (err)
+ return err;
+
+ /* Find first connected pad - its type determines the panel */
+ for (i = 0; i < CLCD_PADS_NUM; i++)
+ if (pads[i] && CLCD_PAD_IS_TFT(pads[i]))
+ return clcdfb_of_init_tft_panel(fb, pads);
+
+ return -EINVAL;
+}
+
+static int clcdfb_of_vram_setup(struct clcd_fb *fb)
+{
+ int err;
+ u32 values[2];
+ phys_addr_t phys_base;
+ size_t size;
+
+ err = clcdfb_of_init_display(fb);
+ if (err)
+ return err;
+
+ err = of_property_read_u32_array(fb->dev->dev.of_node,
+ "arm,pl11x,framebuffer-base",
+ values, ARRAY_SIZE(values));
+ if (err)
+ return err;
+
+ phys_base = values[0];
+ size = values[1];
+
+ fb->fb.screen_base = ioremap(phys_base, size);
+ if (!fb->fb.screen_base)
+ return -ENOMEM;
+
+ fb->fb.fix.smem_start = phys_base;
+ fb->fb.fix.smem_len = size;
+
+ return 0;
+}
+
+static int clcdfb_of_vram_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ unsigned long off, user_size, kernel_size;
+
+ off = vma->vm_pgoff << PAGE_SHIFT;
+ user_size = vma->vm_end - vma->vm_start;
+ kernel_size = fb->fb.fix.smem_len;
+
+ if (off >= kernel_size || user_size > (kernel_size - off))
+ return -ENXIO;
+
+ return remap_pfn_range(vma, vma->vm_start,
+ __phys_to_pfn(fb->fb.fix.smem_start) + vma->vm_pgoff,
+ user_size,
+ pgprot_writecombine(vma->vm_page_prot));
+}
+
+static void clcdfb_of_vram_remove(struct clcd_fb *fb)
+{
+ iounmap(fb->fb.screen_base);
+}
+
+static int clcdfb_of_dma_setup(struct clcd_fb *fb)
+{
+ unsigned long framesize;
+ dma_addr_t dma;
+ int err;
+
+ err = clcdfb_of_init_display(fb);
+ if (err)
+ return err;
+
+ framesize = fb->panel->mode.xres * fb->panel->mode.yres *
+ fb->panel->bpp / 8;
+ fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize,
+ &dma, GFP_KERNEL);
+ if (!fb->fb.screen_base)
+ return -ENOMEM;
+
+ fb->fb.fix.smem_start = dma;
+ fb->fb.fix.smem_len = framesize;
+
+ return 0;
+}
+
+static int clcdfb_of_dma_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
+{
+ return dma_mmap_writecombine(&fb->dev->dev, vma, fb->fb.screen_base,
+ fb->fb.fix.smem_start, fb->fb.fix.smem_len);
+}
+
+static void clcdfb_of_dma_remove(struct clcd_fb *fb)
+{
+ dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
+ fb->fb.screen_base, fb->fb.fix.smem_start);
+}
+
+static struct clcd_board *clcdfb_of_get_board(struct amba_device *dev)
+{
+ struct clcd_board *board = devm_kzalloc(&dev->dev, sizeof(*board),
+ GFP_KERNEL);
+ struct device_node *node = dev->dev.of_node;
+
+ if (!board)
+ return NULL;
+
+ board->name = of_node_full_name(node);
+ board->caps = CLCD_CAP_ALL;
+ board->check = clcdfb_check;
+ board->decode = clcdfb_decode;
+ if (of_find_property(node, "arm,pl11x,framebuffer-base", NULL)) {
+ board->setup = clcdfb_of_vram_setup;
+ board->mmap = clcdfb_of_vram_mmap;
+ board->remove = clcdfb_of_vram_remove;
+ } else {
+ board->setup = clcdfb_of_dma_setup;
+ board->mmap = clcdfb_of_dma_mmap;
+ board->remove = clcdfb_of_dma_remove;
+ }
+
+ return board;
+}
+#else
+static struct clcd_board *clcdfb_of_get_board(struct amba_dev *dev)
+{
+ return NULL;
+}
+#endif
+
static int clcdfb_probe(struct amba_device *dev, const struct amba_id *id)
{
struct clcd_board *board = dev->dev.platform_data;
@@ -549,6 +814,9 @@ static int clcdfb_probe(struct amba_device *dev, const struct amba_id *id)
int ret;
if (!board)
+ board = clcdfb_of_get_board(dev);
+
+ if (!board)
return -EINVAL;
ret = amba_request_regions(dev, NULL);
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
