Hi Mark, On Thu, 2013-09-12 at 17:28 +0100, Mark Rutland wrote: > On Thu, Aug 29, 2013 at 02:27:52PM +0100, Ivan T. Ivanov wrote: > > From: "Ivan T. Ivanov" <iivanov@xxxxxxxxxx> > > > > The Qualcomm Universal Peripherial (QUP) wraps I2C mini-core and > > provide input and output FIFO's for it. I2C controller can operate > > as master with supported bus speeds of 100Kbps and 400Kbps. > > > > Signed-off-by: Ivan T. Ivanov <iivanov@xxxxxxxxxx> > > --- > > Documentation/devicetree/bindings/i2c/i2c-qup.txt | 99 +++++++++++++++++++++ > > 1 file changed, 99 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/i2c/i2c-qup.txt > > > > diff --git a/Documentation/devicetree/bindings/i2c/i2c-qup.txt b/Documentation/devicetree/bindings/i2c/i2c-qup.txt > > new file mode 100644 > > index 0000000..c682726 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/i2c/i2c-qup.txt > > @@ -0,0 +1,99 @@ > > +Qualcomm Universal Periferial (QUP) I2C controller > > + > > +Required properties: > > + - compatible : should be "qcom,i2c-qup" > > + - reg : Offset and length of the register region for the device > > + - interrupts : core interrupt > > How about the following: > > - interrupts: interrupt-specifier for the core interrupt. Ok. > > > + > > + - pinctrl-names: Should contain only one value - "default". > > + - pinctrl-0: Should specify pin control group used for this controller. > > + > > + - clocks : phandles to clock instances of the device tree nodes > > Clocks aren't just phandles, they have a clock-specifier component. This > should probably be something like: > > - clocks: a list of phandle + clock-specifier pairs for each entry in > clock-names Right now MSM clocks [1] are just phandles, I should add #clock-cells = <0>. > > > + - clock-names : > > + "core" : Allow access to FIFO buffers and registers > > Huh? That description doesn't seem to descripe the hardware. How about: Allow access to I2C core FIFO buffers and registers. > > > + "iface" : Clock used by QUP interface > > Which interface? The slave interface the CPUs access, or the interface > to the I2C devices? My understanding for this is that QUP is wrapping I2C core. QUP is interface to I2C core. > > Are these the only clock inputs to the device? Yep. > > Is there a regulator input that might need to be specified? > No. Power management is done via clock gating. > > + > > + - #address-cells : should be <1> Address cells for I2C device address > > + - #size-cells : should be <0> I2C addresses have no size component. > > + > > +Optional properties : > > + - Child nodes conforming to i2c bus binding > > + - clock-frequency : Desired I2C bus clock frequency in Hz. If > > + not set thedefault frequency is 100kHz > > Why is this necessary? This is how I2C bus frequency could be specified. It is standard I2C property. Not sure that I get the question. > > > + - qcom,src-freq : Frequency of the source clocking this bus in Hz. > > + Divider value is set based on soruce-frequency and > > + desired I2C bus frequency. If this value is not > > + provided, the source clock is assumed to be running > > + at 19.2 MHz. > > This looks like it should be a clock input. Thanks, I will change it. Regard, Ivan [1] https://lkml.org/lkml/2013/7/24/729 > > Thanks, > Mark. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
