> 于 2013年09月05日 14:32, Gupta, Pekon 写道:
> >> 于 2013年09月05日 12:25, Gupta, Pekon 写道:
> >>> I would rather suggest to get these values from DT bindings specific to
> >> could you show me what values should i set in the DT bindings?
> >> The spi nor command? or the dummy? or something else?
> >>
> > Taking example of READ command for S25FL128S NOR flash devices..
> > S25FL128S supports following flavors of READ modes.
> > 4FAST_READ Read Fast (4-byte Address) 0C
> > 4READ Read (4-byte Address) 13
> > 4DOR Read Dual Out (4-byte Address) 3C
> > 4QOR Read Quad Out (4-byte Address) 6C
> > 4DIOR Dual I/O Read (4-byte Address) BC
> > 4QIOR Quad I/O Read (4-byte Address) EC
> > 4DDRFR Read DDR Fast (4-byte Address) 0E
> > 4DDRDIOR DDR Dual I/O Read (4-byte Address) BE
> > 4DDRQIOR DDR Quad I/O Read (4-byte Address) EE
> >
> > But due to board constrains and your use-case, you would prefer only few
> > read modes. Those opcodes you can specify via following DT property.
> > "qspi, flash-read-command"
> >
> > Same way you can have DT property for
> > "qspi, flash-write-command"
> > "qspi, flash-erase-command"
> > "qspi, flash-address-mode" =<4-byte/3-byte>
> > "qspi, flash-dummy-cycles" =<integer>
> thanks for your suggestion.
>
> I ever thought of this solution.
>
> But i do not think this is not a good solution. :(
>
Sorry.. I din't mean to be offensive, I should re-word my feedback as
your previous solution is not scalable. My suggestion is just a
food-for-thought, approvals from other users is required here.
> Firstly, the NOR flash S25FL128S may be used by other boards or other
> platform.
> So if other person uses the S25FL128S, he has to add the SPI NOR
> command(such as 0xbe, 0xec),
> this is really not needed. Why not add these SPI NOR command now?
>
>
> Secondly, this controller not only needs the write/erase/read, but also
> need other SPI NOR commands
> such as Write-Enable/Read-status/Configurate the Register. if we add
> these SPI NOR commands to
> the DT binding, it will be more ugly to veryone. That's why the Patch 1
> is needed.
>
>
> The only value should be set in the DT is the _dummy_ value. But Add the
> dummy support should be an other
> patchset's job. I think it is a little complicated to add the dummy support.
>
> The fast-read uses 8bit dummy, the quad-read may needs 6bit dummy, and
> so on..
>
> How can we transfer the dummy value to the device? Add a value to the
> spi_transfer{}?
> I planed to submit another patchset to fix the dummy issue, since it
> maybe needs more discussion,
> i did not include the dummy patches in this patch set.
>
No, SPI generic framework (struct spi_transfer, spi_message,...)
should be kept independent of any MTD flash specific data handlers.
<wangyuhang2014@xxxxxxxxx> added two new fields (tx_nbits, rx_nbits)
to spi_device because those properties are part of SPI protocol.
But, 'dummy_cycles' is no related to SPI protocol. So it should be kept out
of SPI generic framework.
This is where if you could use DT based approach, things would have been
simpler, because you give end-user the freedom to enter device-info from
device datasheet.
>
>
>
>
>
>
>
> > Example: How to select opcodes in DT ?
> > (step-1) eliminate opcode which cannot be used due to board constrains.
> > your board connects only 2 data I/O between device and controller, So you
> > cannot use any of the QUAD Read opcodes. Thus your choice is limited to
> > DUAL or SINGLE modes only.
> we have 4 data I/O lines between the device and controller, i only need
> the Quad mode. :)
>
May be because you are currently working on a development EVM or
demo board, so you can live with QUAD mode.
But when customer will have custom boards with different QSPI devices
then you would end-up supporting all sorts of configurations :-)
And in production scenarios, it’s the price economics which mostly dominates
which part to choose and how to connect it on board.
Like as I remember some freescale boards have WINBOND QSPI flash
which uses different opcodes and semantics, so you might need to support
that too in future.
So my suggestion is think again. As you are inviting lot of re-work for yourself
and for others too :-)
Anyway, if you really want to continue with this is, then please re-name
include/linux/mtd/spi-nor.h to
include/linux/mtd/spi-fsl-quadspi.h
because something specific for your driver should not conflict with
generic spi-nor framework added later.
with regards, pekon
��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
