This patch updates the exynos-dw-mshc.txt.Currently we are using
"pinctrl" binding property to describe the CMD and DATA line's
of Mobile Storage Host Controller(mshc) node.
Compatibility string is added in the driver with the patch.
[1] mmc: dw_mmc: exynos: configure SMU in exynos5420.
DT nodes has been added in separate patch.
[2] ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx>
---
.../devicetree/bindings/mmc/exynos-dw-mshc.txt | 39 +++++++++++---------
1 file changed, 21 insertions(+), 18 deletions(-)
diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
index 84cd56f..0e1d4d9 100644
--- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt
@@ -7,9 +7,9 @@ differences between the core Synopsis dw mshc controller properties described
by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific
extensions to the Synopsis Designware Mobile Storage Host Controller.
-Required Properties:
+Required SoC Specific Properties:
-* compatible: should be
+* compatible: should be one of the following
- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
specific extensions.
- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
@@ -17,7 +17,12 @@ Required Properties:
- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
specific extensions.
- "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420
- specific extensions.
+ specific extensions which does not have SMU(Security Management Unit).
+ - "samsung,exynos5420-dw-mshc-smu": for controllers with Samsung
+ Exynos5420 specific extensions which has SMU(Security Management
+ Unit).
+
+Required Board Specific Properties:
* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
@@ -46,44 +51,42 @@ Required Properties:
- if CIU clock divider value is 0 (that is divide by 1), both tx and rx
phase shift clocks should be 0.
-Required properties for a slot:
-
-* gpios: specifies a list of gpios used for command, clock and data bus. The
- first gpio is the command line and the second gpio is the clock line. The
- rest of the gpios (depending on the bus-width property) are the data lines in
- no particular order. The format of the gpio specifier depends on the gpio
- controller.
+* pinctrl-0: Should specify pin control groups used for this controller.
+* pinctrl-names: Should contain only one value - "default".
+Required properties for a slot:
+ Refer synopsis-dw-mshc.txt
Example:
The MSHC controller node can be split into two portions, SoC specific and
board specific portions as listed below.
- dwmmc0@12200000 {
+ mshc@12200000 {
compatible = "samsung,exynos5250-dw-mshc";
reg = <0x12200000 0x1000>;
interrupts = <0 75 0>;
#address-cells = <1>;
#size-cells = <0>;
+ clocks = <&clock 351>, <&clock 132>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x80>;
+ status = "disabled";
};
- dwmmc0@12200000 {
+ mshc@12200000 {
+ status = "okay";
num-slots = <1>;
supports-highspeed;
broken-cd;
- fifo-depth = <0x80>;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
slot@0 {
reg = <0>;
bus-width = <8>;
- gpios = <&gpc0 0 2 0 3>, <&gpc0 1 2 0 3>,
- <&gpc1 0 2 3 3>, <&gpc1 1 2 3 3>,
- <&gpc1 2 2 3 3>, <&gpc1 3 2 3 3>,
- <&gpc0 3 2 3 3>, <&gpc0 4 2 3 3>,
- <&gpc0 5 2 3 3>, <&gpc0 6 2 3 3>;
};
};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
