From: Alison Chaiken <alison_chaiken@xxxxxxxxxx> Update documentation file fsl,imx-pinctrl.txt to match iomuxc pinctrl config settings to reflect Rev. 1 (4/2013) of IMX6DQRM, i.MX6 technical reference manual. Signed-off-by: Alison Chaiken <alison_chaiken@xxxxxxxxxx> --- .../bindings/pinctrl/fsl,imx-pinctrl.txt | 25 +++++++++++----------- 1 file changed, 13 insertions(+), 12 deletions(-) diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt index 3a7caf7..9b347f1 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt @@ -72,23 +72,24 @@ iomuxc@020e0000 { /* shared pinctrl settings */ usdhc4 { pinctrl_usdhc4_1: usdhc4grp-1 { - fsl,pins = <1386 0x17059 /* MX6Q_PAD_SD4_CMD__USDHC4_CMD */ + fsl,pins = <1386 0x1b0b0 /* MX6Q_PAD_SD4_CMD__USDHC4_CMD */ 1392 0x10059 /* MX6Q_PAD_SD4_CLK__USDHC4_CLK */ - 1462 0x17059 /* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */ - 1470 0x17059 /* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */ - 1478 0x17059 /* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */ - 1486 0x17059 /* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */ - 1493 0x17059 /* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */ - 1501 0x17059 /* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */ - 1509 0x17059 /* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */ - 1517 0x17059>; /* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */ + 1462 0x1b0b0 /* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */ + 1470 0x1b0b0 /* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */ + 1478 0x1b0b0 /* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */ + 1486 0x1b0b0 /* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */ + 1493 0x1b0b0 /* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */ + 1501 0x1b0b0 /* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */ + 1509 0x1b0b0 /* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */ + 1517 0x1b0b0>; /* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */ }; }; .... }; -Refer to the IOMUXC controller chapter in imx6q datasheet, -0x17059 means enable hysteresis, 47KOhm Pull Up, 50Mhz speed, -80Ohm driver strength and Fast Slew Rate. +Referring to "Pin Assignments" Table of "i.MX 6Dual/6Quad Applications Processor +Reference Manual, Rev. 1, 04/2013", +0x1b0b0 means enable hysteresis, 100KOhm Pull Up, 100Mhz speed, +40Ohm driver strength and Slow Slew Rate. User should refer to each SoC spec to set the correct value. TODO: when dtc macro support is available, we can change above raw data -- 1.8.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html