Hello Florian,
On 22/08/2013 17:57, Boris BREZILLON wrote:
The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.
This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.
Signed-off-by: Boris BREZILLON <b.brezillon@xxxxxxxxxxx>
---
drivers/net/ethernet/cadence/macb.c | 41 +++++++++++++++++++++++++++++------
1 file changed, 34 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c
index e866608..fe06ab0 100644
--- a/drivers/net/ethernet/cadence/macb.c
+++ b/drivers/net/ethernet/cadence/macb.c
@@ -27,6 +27,7 @@
#include <linux/phy.h>
#include <linux/of.h>
#include <linux/of_device.h>
+#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include <linux/pinctrl/consumer.h>
@@ -314,6 +315,7 @@ static int macb_mii_probe(struct net_device *dev)
int macb_mii_init(struct macb *bp)
{
struct macb_platform_data *pdata;
+ struct device_node *np;
int err = -ENXIO, i;
/* Enable management port */
@@ -335,21 +337,46 @@ int macb_mii_init(struct macb *bp)
bp->mii_bus->parent = &bp->dev->dev;
pdata = bp->pdev->dev.platform_data;
- if (pdata)
- bp->mii_bus->phy_mask = pdata->phy_mask;
-
bp->mii_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);
if (!bp->mii_bus->irq) {
err = -ENOMEM;
goto err_out_free_mdiobus;
}
- for (i = 0; i < PHY_MAX_ADDR; i++)
- bp->mii_bus->irq[i] = PHY_POLL;
-
dev_set_drvdata(&bp->dev->dev, bp->mii_bus);
- if (mdiobus_register(bp->mii_bus))
+ np = bp->pdev->dev.of_node;
+ if (np) {
+ /* try dt phy registration */
+ err = of_mdiobus_register(bp->mii_bus, np);
+
+ /* fallback to standard phy registration if no phy were
+ found during dt phy registration */
+ if (!err && !phy_find_first(bp->mii_bus)) {
+ for (i = 0; i < PHY_MAX_ADDR; i++) {
+ struct phy_device *phydev;
+
+ phydev = mdiobus_scan(bp->mii_bus, i);
+ if (IS_ERR(phydev)) {
+ err = PTR_ERR(phydev);
+ break;
+ }
+ }
+
This is were I need the mdiobus_full_scan function.
+ if (err)
+ goto err_out_unregister_bus;
+ }
+ } else {
+ for (i = 0; i < PHY_MAX_ADDR; i++)
+ bp->mii_bus->irq[i] = PHY_POLL;
+
+ if (pdata)
+ bp->mii_bus->phy_mask = pdata->phy_mask;
+
+ err = mdiobus_register(bp->mii_bus);
+ }
+
+ if (err)
goto err_out_free_mdio_irq;
if (macb_mii_probe(bp->dev) != 0) {
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html