Jonathan Cameron <jic23@xxxxxxxxxx> wrote: >On 08/16/13 13:12, Oleksandr Kravchenko wrote: >> This patch adds IIO driver for Bosch BMA180 triaxial >> acceleration sensor. >> http://dlnmh9ip6v2uc.cloudfront.net/datasheets/ >> Sensors/Accelerometers/BST-BMA180-DS000-07_2.pdf >> >> Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@xxxxxxxxxxxxxxx> > >Surely your power_mode ext_info entry wants to be shared? >It is the same control for all 3 accelerometer channels... Or drop it out of chanspec entirely so that it can be just power_mode. If I hadn't messed up handling extinfo in the set I sent easier this would be easier. > >Jonathan > >> --- >> .../devicetree/bindings/iio/accel/bma180.txt | 24 + >> drivers/iio/accel/Kconfig | 12 + >> drivers/iio/accel/Makefile | 2 + >> drivers/iio/accel/bma180.c | 676 >++++++++++++++++++++ >> 4 files changed, 714 insertions(+) >> create mode 100644 >Documentation/devicetree/bindings/iio/accel/bma180.txt >> create mode 100644 drivers/iio/accel/bma180.c >> >> diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt >b/Documentation/devicetree/bindings/iio/accel/bma180.txt >> new file mode 100644 >> index 0000000..c593357 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/iio/accel/bma180.txt >> @@ -0,0 +1,24 @@ >> +* Bosch BMA180 triaxial acceleration sensor >> + >> +http://omapworld.com/BMA180_111_1002839.pdf >> + >> +Required properties: >> + >> + - compatible : should be "bosch,bma180" >> + - reg : the I2C address of the sensor >> + >> +Optional properties: >> + >> + - interrupt-parent : should be the phandle for the interrupt >controller >> + >> + - interrupts : interrupt mapping for GPIO IRQ, it should by >configured with >> + flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING >> + >> +Example: >> + >> +bma180@40 { >> + compatible = "bosch,bma180"; >> + reg = <0x40>; >> + interrupt-parent = <&gpio6>; >> + interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; >> +}; >> diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig >> index 719d83f..bd9d581 100644 >> --- a/drivers/iio/accel/Kconfig >> +++ b/drivers/iio/accel/Kconfig >> @@ -3,6 +3,18 @@ >> # >> menu "Accelerometers" >> >> +config BMA180 >> + tristate "Bosch BMA180 3-Axis Accelerometer Driver" >> + depends on I2C >> + select IIO_BUFFER >> + select IIO_TRIGGERED_BUFFER >> + help >> + Say Y here if you want to build a driver for the Bosch BMA180 >> + triaxial acceleration sensor. >> + >> + To compile this driver as a module, choose M here: the >> + module will be called bma180. >> + >> config HID_SENSOR_ACCEL_3D >> depends on HID_SENSOR_HUB >> select IIO_BUFFER >> diff --git a/drivers/iio/accel/Makefile b/drivers/iio/accel/Makefile >> index 87d8fa2..eb09d72 100644 >> --- a/drivers/iio/accel/Makefile >> +++ b/drivers/iio/accel/Makefile >> @@ -2,6 +2,8 @@ >> # Makefile for industrial I/O accelerometer drivers >> # >> >> +obj-$(CONFIG_BMA180) += bma180.o >> + >> obj-$(CONFIG_HID_SENSOR_ACCEL_3D) += hid-sensor-accel-3d.o >> >> obj-$(CONFIG_IIO_ST_ACCEL_3AXIS) += st_accel.o >> diff --git a/drivers/iio/accel/bma180.c b/drivers/iio/accel/bma180.c >> new file mode 100644 >> index 0000000..ae15580 >> --- /dev/null >> +++ b/drivers/iio/accel/bma180.c >> @@ -0,0 +1,676 @@ >> +/* >> + * bma180.c - IIO driver for Bosch BMA180 triaxial acceleration >sensor >> + * >> + * Copyright 2013 Oleksandr Kravchenko <x0199363@xxxxxx> >> + * >> + * This file is subject to the terms and conditions of version 2 of >> + * the GNU General Public License. See the file COPYING in the main >> + * directory of this archive for more details. >> + */ >> + >> +#include <linux/module.h> >> +#include <linux/i2c.h> >> +#include <linux/interrupt.h> >> +#include <linux/delay.h> >> +#include <linux/of.h> >> +#include <linux/bitops.h> >> +#include <linux/slab.h> >> +#include <linux/string.h> >> +#include <linux/iio/iio.h> >> +#include <linux/iio/sysfs.h> >> +#include <linux/iio/buffer.h> >> +#include <linux/iio/trigger.h> >> +#include <linux/iio/trigger_consumer.h> >> +#include <linux/iio/triggered_buffer.h> >> + >> +#define BMA180_DRV_NAME "bma180" >> +#define BMA180_IRQ_NAME "bma180_event" >> + >> +/* Register set */ >> +#define BMA180_CHIP_ID 0x00 /* Need to distinguish BMA180 from >other */ >> +#define BMA180_ACC_X_LSB 0x02 /* First of 6 registers of accel data >*/ >> +#define BMA180_CTRL_REG0 0x0d >> +#define BMA180_RESET 0x10 >> +#define BMA180_BW_TCS 0x20 >> +#define BMA180_CTRL_REG3 0x21 >> +#define BMA180_TCO_Z 0x30 >> +#define BMA180_OFFSET_LSB1 0x35 >> + >> +/* BMA180_CTRL_REG0 bits */ >> +#define BMA180_DIS_WAKE_UP BIT(0) /* Disable wake up mode */ >> +#define BMA180_SLEEP BIT(1) /* 1 - chip will sleep */ >> +#define BMA180_EE_W BIT(4) /* Unlock writing to addr from 0x20 */ >> +#define BMA180_RESET_INT BIT(6) /* Reset pending interrupts */ >> + >> +/* BMA180_CTRL_REG3 bits */ >> +#define BMA180_NEW_DATA_INT BIT(1) /* Intr every new accel data is >ready */ >> + >> +/* BMA180_OFFSET_LSB1 skipping mode bit */ >> +#define BMA180_SMP_SKIP BIT(0) >> + >> +/* Bit masks for registers bit fields */ >> +#define BMA180_RANGE 0x0e /* Range of measured accel values*/ >> +#define BMA180_BW 0xf0 /* Accel bandwidth */ >> +#define BMA180_MODE_CONFIG 0x03 /* Config operation modes */ >> + >> +/* We have to write this value in reset register to do soft reset */ >> +#define BMA180_RESET_VAL 0xb6 >> + >> +#define BMA_180_ID_REG_VAL 0x03 >> + >> +/* Chip power modes */ >> +#define BMA180_LOW_NOISE 0x00 >> +#define BMA180_LOW_POWER 0x03 >> + >> +#define BMA180_LOW_NOISE_STR "low_noise" >> +#define BMA180_LOW_POWER_STR "low_power" >> + >> +/* Defaults values */ >> +#define BMA180_DEF_PMODE 0 >> +#define BMA180_DEF_BW 20 >> +#define BMA180_DEF_SCALE 250 >> + >> +/* Available values for sysfs */ >> +#define BMA180_FLP_FREQ_AVAILABLE \ >> + "10 20 40 75 150 300" >> +#define BMA180_SCALE_AVAILABLE \ >> + "0.000130 0.000190 0.000250 0.000380 0.000500 0.000990 0.001980" >> + >> +struct bma180_data { >> + struct i2c_client *client; >> + struct iio_trigger *trig; >> + struct mutex mutex; >> + int sleep_state; >> + int scale; >> + int bw; >> + int pmode; >> + char *buff; >> +}; >> + >> +enum bma180_axis { >> + AXIS_X, >> + AXIS_Y, >> + AXIS_Z, >> +}; >> + >> +static int bw_table[] = { 10, 20, 40, 75, 150, 300 }; /* Hz */ >> +static int scale_table[] = { 130, 190, 250, 380, 500, 990, 1980 }; >> + >> +static int bma180_get_acc_reg(struct bma180_data *data, enum >bma180_axis axis) >> +{ >> + u8 reg = BMA180_ACC_X_LSB + axis * 2; >> + int ret; >> + >> + if (data->sleep_state) >> + return -EBUSY; >> + >> + ret = i2c_smbus_read_word_data(data->client, reg); >> + if (ret < 0) >> + dev_err(&data->client->dev, >> + "failed to read accel_%c registers\n", 'x' + axis); >> + >> + return ret; >> +} >> + >> +static int bma180_set_bits(struct bma180_data *data, u8 reg, u8 >mask, u8 val) >> +{ >> + int ret = i2c_smbus_read_byte_data(data->client, reg); >> + u8 reg_val = (ret & ~mask) | (val << (ffs(mask) - 1)); >> + >> + if (ret < 0) >> + return ret; >> + >> + return i2c_smbus_write_byte_data(data->client, reg, reg_val); >> +} >> + >> +static int bma180_reset_intr(struct bma180_data *data) >> +{ >> + int ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_RESET_INT, >1); >> + >> + if (ret) >> + dev_err(&data->client->dev, "failed to reset interrupt\n"); >> + >> + return ret; >> +} >> + >> +static int bma180_set_new_data_intr_state(struct bma180_data *data, >int state) >> +{ >> + u8 reg_val = state ? BMA180_NEW_DATA_INT : 0x00; >> + int ret = i2c_smbus_write_byte_data(data->client, BMA180_CTRL_REG3, >> + reg_val); >> + >> + if (ret) >> + goto err; >> + ret = bma180_reset_intr(data); >> + if (ret) >> + goto err; >> + >> + return 0; >> + >> +err: >> + dev_err(&data->client->dev, >> + "failed to set new data interrupt state %d\n", state); >> + return ret; >> +} >> + >> +static int bma180_set_sleep_state(struct bma180_data *data, int >state) >> +{ >> + int ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_SLEEP, >state); >> + >> + if (ret) { >> + dev_err(&data->client->dev, >> + "failed to set sleep state %d\n", state); >> + return ret; >> + } >> + data->sleep_state = state; >> + >> + return 0; >> +} >> + >> +static int bma180_set_ee_writing_state(struct bma180_data *data, int >state) >> +{ >> + int ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_EE_W, >state); >> + >> + if (ret) >> + dev_err(&data->client->dev, >> + "failed to set ee writing state %d\n", state); >> + >> + return ret; >> +} >> + >> +static int bma180_set_bw(struct bma180_data *data, int val) >> +{ >> + int ret, i; >> + >> + if (data->sleep_state) >> + return -EBUSY; >> + >> + for (i = 0; i < ARRAY_SIZE(bw_table); ++i) { >> + if (bw_table[i] == val) { >> + ret = bma180_set_bits(data, >> + BMA180_BW_TCS, BMA180_BW, i); >> + if (ret) { >> + dev_err(&data->client->dev, >> + "failed to set bandwidth\n"); >> + return ret; >> + } >> + data->bw = val; >> + return 0; >> + } >> + } >> + >> + return -EINVAL; >> +} >> + >> +static int bma180_set_scale(struct bma180_data *data, int val) >> +{ >> + int ret, i; >> + >> + if (data->sleep_state) >> + return -EBUSY; >> + >> + for (i = 0; i < ARRAY_SIZE(scale_table); ++i) >> + if (scale_table[i] == val) { >> + ret = bma180_set_bits(data, >> + BMA180_OFFSET_LSB1, BMA180_RANGE, i); >> + if (ret) { >> + dev_err(&data->client->dev, >> + "failed to set scale\n"); >> + return ret; >> + } >> + data->scale = val; >> + return 0; >> + } >> + >> + return -EINVAL; >> +} >> + >> +static int bma180_set_pmode(struct bma180_data *data, int mode) >> +{ >> + u8 reg_val = mode ? BMA180_LOW_POWER : BMA180_LOW_NOISE; >> + int ret = bma180_set_bits(data, BMA180_TCO_Z, BMA180_MODE_CONFIG, >> + reg_val); >> + >> + if (ret) { >> + dev_err(&data->client->dev, "failed to set power mode\n"); >> + return ret; >> + } >> + data->pmode = mode; >> + >> + return 0; >> +} >> + >> +static int bma180_soft_reset(struct bma180_data *data) >> +{ >> + int ret = i2c_smbus_write_byte_data(data->client, >> + BMA180_RESET, BMA180_RESET_VAL); >> + >> + if (ret) >> + dev_err(&data->client->dev, "failed to reset the chip\n"); >> + >> + return ret; >> +} >> + >> +static int bma180_chip_init(struct bma180_data *data) >> +{ >> + /* Try to read chip_id register. It must return 0x03. */ >> + int ret = i2c_smbus_read_byte_data(data->client, BMA180_CHIP_ID); >> + >> + if (ret < 0) >> + goto err; >> + if (ret != BMA_180_ID_REG_VAL) { >> + ret = -ENODEV; >> + goto err; >> + } >> + >> + ret = bma180_soft_reset(data); >> + if (ret) >> + goto err; >> + /* >> + * No serial transaction should occur within minimum 10 us >> + * after soft_reset command >> + */ >> + msleep(20); >> + >> + ret = bma180_set_bits(data, BMA180_CTRL_REG0, BMA180_DIS_WAKE_UP, >1); >> + if (ret) >> + goto err; >> + ret = bma180_set_ee_writing_state(data, 1); >> + if (ret) >> + goto err; >> + ret = bma180_set_new_data_intr_state(data, 0); >> + if (ret) >> + goto err; >> + ret = bma180_set_bits(data, BMA180_OFFSET_LSB1, BMA180_SMP_SKIP, >1); >> + if (ret) >> + goto err; >> + ret = bma180_set_pmode(data, BMA180_DEF_PMODE); >> + if (ret) >> + goto err; >> + ret = bma180_set_bw(data, BMA180_DEF_BW); >> + if (ret) >> + goto err; >> + ret = bma180_set_scale(data, BMA180_DEF_SCALE); >> + if (ret) >> + goto err; >> + >> + return 0; >> + >> +err: >> + dev_err(&data->client->dev, "failed to init the chip\n"); >> + return ret; >> +} >> + >> +static void bma180_chip_disable(struct bma180_data *data) >> +{ >> + if (bma180_set_new_data_intr_state(data, 0)) >> + goto err; >> + if (bma180_set_ee_writing_state(data, 0)) >> + goto err; >> + if (bma180_set_sleep_state(data, 1)) >> + goto err; >> + >> + return; >> + >> +err: >> + dev_err(&data->client->dev, "failed to disable the chip\n"); >> +} >> + >> +static >IIO_CONST_ATTR(in_accel_filter_low_pass_3db_frequency_available, >> + BMA180_FLP_FREQ_AVAILABLE); >> +static IIO_CONST_ATTR(in_accel_scale_available, >BMA180_SCALE_AVAILABLE); >> + >> +static struct attribute *bma180_attributes[] = { >> >+ &iio_const_attr_in_accel_filter_low_pass_3db_frequency_available.dev_attr.attr, >> + &iio_const_attr_in_accel_scale_available.dev_attr.attr, >> + NULL, >> +}; >> + >> +static const struct attribute_group bma180_attrs_group = { >> + .attrs = bma180_attributes, >> +}; >> + >> +static int bma180_read_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, int *val, int *val2, >> + long mask) >> +{ >> + struct bma180_data *data = iio_priv(indio_dev); >> + int ret; >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_RAW: >> + mutex_lock(&data->mutex); >> + if (iio_buffer_enabled(indio_dev)) >> + ret = -EBUSY; >> + else >> + ret = bma180_get_acc_reg(data, chan->scan_index); >> + mutex_unlock(&data->mutex); >> + if (ret < 0) >> + return ret; >> + *val = (s16)ret >> chan->scan_type.shift; >> + return IIO_VAL_INT; >> + case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: >> + *val = data->bw; >> + return IIO_VAL_INT; >> + case IIO_CHAN_INFO_SCALE: >> + *val = 0; >> + *val2 = data->scale; >> + return IIO_VAL_INT_PLUS_MICRO; >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static int bma180_write_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, int val, int val2, long mask) >> +{ >> + struct bma180_data *data = iio_priv(indio_dev); >> + int ret; >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_SCALE: >> + if (val) >> + return -EINVAL; >> + mutex_lock(&data->mutex); >> + ret = bma180_set_scale(data, val2); >> + mutex_unlock(&data->mutex); >> + return ret; >> + case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: >> + mutex_lock(&data->mutex); >> + ret = bma180_set_bw(data, val); >> + mutex_unlock(&data->mutex); >> + return ret; >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static int bma180_update_scan_mode(struct iio_dev *indio_dev, >> + const unsigned long *scan_mask) >> +{ >> + struct bma180_data *data = iio_priv(indio_dev); >> + >> + if (data->buff) >> + devm_kfree(&indio_dev->dev, data->buff); >> + data->buff = devm_kzalloc(&indio_dev->dev, >> + indio_dev->scan_bytes, GFP_KERNEL); >> + if (!data->buff) >> + return -ENOMEM; >> + >> + return 0; >> +} >> + >> +static const struct iio_info bma180_info = { >> + .attrs = &bma180_attrs_group, >> + .read_raw = bma180_read_raw, >> + .write_raw = bma180_write_raw, >> + .update_scan_mode = bma180_update_scan_mode, >> + .driver_module = THIS_MODULE, >> +}; >> + >> +static const char * const bma180_power_modes[] = { >> + BMA180_LOW_NOISE_STR, >> + BMA180_LOW_POWER_STR, >> +}; >> + >> +static int bma180_get_power_mode(struct iio_dev *indio_dev, >> + const struct iio_chan_spec *chan) >> +{ >> + struct bma180_data *data = iio_priv(indio_dev); >> + >> + return data->pmode; >> +} >> + >> +static int bma180_set_power_mode(struct iio_dev *indio_dev, >> + const struct iio_chan_spec *chan, unsigned int mode) >> +{ >> + struct bma180_data *data = iio_priv(indio_dev); >> + int ret; >> + >> + mutex_lock(&data->mutex); >> + ret = bma180_set_pmode(data, mode); >> + mutex_unlock(&data->mutex); >> + >> + return ret; >> +} >> + >> +static const struct iio_enum bma180_power_mode_enum = { >> + .items = bma180_power_modes, >> + .num_items = ARRAY_SIZE(bma180_power_modes), >> + .get = bma180_get_power_mode, >> + .set = bma180_set_power_mode, >> +}; >> + >> +static const struct iio_chan_spec_ext_info bma180_ext_info[] = { >True for the shared? >> + IIO_ENUM("power_mode", false, &bma180_power_mode_enum), >> + IIO_ENUM_AVAILABLE("power_mode", &bma180_power_mode_enum), >> + { }, >> +}; >> + >> +#define BMA180_CHANNEL(_index) { \ >> + .type = IIO_ACCEL, \ >> + .indexed = 1, \ >> + .channel = (_index), \ >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ >> + BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY), \ >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ >> + .scan_index = (_index), \ >> + .scan_type = IIO_ST('s', 14, 16, 2), \ >> + .ext_info = bma180_ext_info, \ >> +} >> + >> +static const struct iio_chan_spec bma180_channels[] = { >> + BMA180_CHANNEL(AXIS_X), >> + BMA180_CHANNEL(AXIS_Y), >> + BMA180_CHANNEL(AXIS_Z), >> + IIO_CHAN_SOFT_TIMESTAMP(4), >> +}; >> + >> +static irqreturn_t bma180_trigger_handler(int irq, void *p) >> +{ >> + struct iio_poll_func *pf = p; >> + struct iio_dev *indio_dev = pf->indio_dev; >> + struct bma180_data *data = iio_priv(indio_dev); >> + int bit, ret, i = 0; >> + >> + mutex_lock(&data->mutex); >> + if (indio_dev->scan_timestamp) { >> + ret = indio_dev->scan_bytes / sizeof(s64) - 1; >> + ((s64 *)data->buff)[ret] = iio_get_time_ns(); >> + } >> + >> + for_each_set_bit(bit, indio_dev->buffer->scan_mask, >> + indio_dev->masklength) { >> + ret = bma180_get_acc_reg(data, bit); >> + if (ret < 0) { >> + mutex_unlock(&data->mutex); >> + goto err; >> + } >> + ((s16 *)data->buff)[i++] = ret; >> + } >> + mutex_unlock(&data->mutex); >> + >> + iio_push_to_buffers(indio_dev, (u8 *)data->buff); >> +err: >> + iio_trigger_notify_done(indio_dev->trig); >> + >> + return IRQ_HANDLED; >> +} >> + >> +static int bma180_data_rdy_trigger_set_state(struct iio_trigger >*trig, >> + bool state) >> +{ >> + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); >> + struct bma180_data *data = iio_priv(indio_dev); >> + >> + return bma180_set_new_data_intr_state(data, state); >> +} >> + >> +static int bma180_trig_try_reen(struct iio_trigger *trig) >> +{ >> + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); >> + struct bma180_data *data = iio_priv(indio_dev); >> + >> + return bma180_reset_intr(data); >> +} >> + >> +static const struct iio_trigger_ops bma180_trigger_ops = { >> + .set_trigger_state = bma180_data_rdy_trigger_set_state, >> + .try_reenable = bma180_trig_try_reen, >> + .owner = THIS_MODULE, >> +}; >> + >> +static int bma180_probe(struct i2c_client *client, >> + const struct i2c_device_id *id) >> +{ >> + struct bma180_data *data; >> + struct iio_dev *indio_dev; >> + struct iio_trigger *trig; >> + int ret; >> + >> + indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data)); >> + if (!indio_dev) >> + return -ENOMEM; >> + >> + data = iio_priv(indio_dev); >> + i2c_set_clientdata(client, indio_dev); >> + data->client = client; >> + >> + ret = bma180_chip_init(data); >> + if (ret < 0) >> + goto err_chip_disable; >> + >> + mutex_init(&data->mutex); >> + >> + indio_dev->dev.parent = &client->dev; >> + indio_dev->channels = bma180_channels; >> + indio_dev->num_channels = ARRAY_SIZE(bma180_channels); >> + indio_dev->name = BMA180_DRV_NAME; >> + indio_dev->modes = INDIO_DIRECT_MODE; >> + indio_dev->info = &bma180_info; >> + >> + trig = iio_trigger_alloc("%s-dev%d", indio_dev->name, >indio_dev->id); >> + if (!trig) { >> + ret = -ENOMEM; >> + goto err_chip_disable; >> + } >> + >> + ret = devm_request_irq(&client->dev, client->irq, >> + iio_trigger_generic_data_rdy_poll, >> + IRQF_TRIGGER_RISING, BMA180_IRQ_NAME, trig); >> + if (ret) { >> + dev_err(&client->dev, "unable to request IRQ\n"); >> + goto err_trigger_free; >> + } >> + >> + trig->dev.parent = &client->dev; >> + trig->ops = &bma180_trigger_ops; >> + iio_trigger_set_drvdata(trig, indio_dev); >> + data->trig = trig; >> + indio_dev->trig = trig; >> + >> + ret = iio_trigger_register(trig); >> + if (ret) >> + goto err_trigger_free; >> + >> + ret = iio_triggered_buffer_setup(indio_dev, NULL, >> + bma180_trigger_handler, NULL); >> + if (ret < 0) { >> + dev_err(&client->dev, "unable to setup iio triggered buffer\n"); >> + goto err_trigger_unregister; >> + } >> + >> + ret = iio_device_register(indio_dev); >> + if (ret < 0) { >> + dev_err(&client->dev, "unable to register iio device\n"); >> + goto err_buffer_cleanup; >> + } >> + >> + return 0; >> + >> +err_buffer_cleanup: >> + iio_triggered_buffer_cleanup(indio_dev); >> +err_trigger_unregister: >> + iio_trigger_unregister(trig); >> +err_trigger_free: >> + iio_trigger_free(trig); >> +err_chip_disable: >> + bma180_chip_disable(data); >> + >> + return ret; >> +} >> + >> +static int bma180_remove(struct i2c_client *client) >> +{ >> + struct iio_dev *indio_dev = i2c_get_clientdata(client); >> + struct bma180_data *data = iio_priv(indio_dev); >> + >> + iio_device_unregister(indio_dev); >> + iio_triggered_buffer_cleanup(indio_dev); >> + iio_trigger_unregister(data->trig); >> + iio_trigger_free(data->trig); >> + >> + mutex_lock(&data->mutex); >> + bma180_chip_disable(data); >> + mutex_unlock(&data->mutex); >> + >> + return 0; >> +} >> + >> +#ifdef CONFIG_PM_SLEEP >> +static int bma180_suspend(struct device *dev) >> +{ >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev); >> + struct bma180_data *data = iio_priv(indio_dev); >> + int ret; >> + >> + mutex_lock(&data->mutex); >> + ret = bma180_set_sleep_state(data, 1); >> + mutex_unlock(&data->mutex); >> + >> + return ret; >> +} >> + >> +static int bma180_resume(struct device *dev) >> +{ >> + struct iio_dev *indio_dev = dev_to_iio_dev(dev); >> + struct bma180_data *data = iio_priv(indio_dev); >> + int ret; >> + >> + mutex_lock(&data->mutex); >> + ret = bma180_set_sleep_state(data, 0); >> + mutex_unlock(&data->mutex); >> + >> + return ret; >> +} >> + >> +static SIMPLE_DEV_PM_OPS(bma180_pm_ops, bma180_suspend, >bma180_resume); >> +#define BMA180_PM_OPS (&bma180_pm_ops) >> +#else >> +#define BMA180_PM_OPS NULL >> +#endif >> + >> +static struct i2c_device_id bma180_id[] = { >> + { BMA180_DRV_NAME, 0 }, >> + { } >> +}; >> + >> +MODULE_DEVICE_TABLE(i2c, bma180_id); >> + >> +static struct i2c_driver bma180_driver = { >> + .driver = { >> + .name = BMA180_DRV_NAME, >> + .owner = THIS_MODULE, >> + .pm = BMA180_PM_OPS, >> + }, >> + .probe = bma180_probe, >> + .remove = bma180_remove, >> + .id_table = bma180_id, >> +}; >> + >> +module_i2c_driver(bma180_driver); >> + >> +MODULE_AUTHOR("Kravchenko Oleksandr <x0199363@xxxxxx>"); >> +MODULE_AUTHOR("Texas Instruments, Inc."); >> +MODULE_DESCRIPTION("Bosch BMA180 triaxial acceleration sensor"); >> +MODULE_LICENSE("GPL"); >> >-- >To unsubscribe from this list: send the line "unsubscribe linux-iio" in >the body of a message to majordomo@xxxxxxxxxxxxxxx >More majordomo info at http://vger.kernel.org/majordomo-info.html -- Sent from my Android phone with K-9 Mail. Please excuse my brevity. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
