Hi Digmer, Hi Andrew, I confirmed that it was not necessary to appoint nodeid in totem. Please revise node2 equally. --------- node1 /etc/corosync.conf ----------------------------- # Please read the corosync.conf.5 manual page compatibility: whitetank totem { version: 2 secauth: off rrp_mode:active interface { ringnumber: 0 bindnetaddr: 2001:db8:50::250 ttl: 1 } interface { ringnumber: 1 bindnetaddr: 2001:db8:60::250 ttl: 1 } transport: udpu } (snip) quorum { provider: corosync_votequorum votes: 1 } nodelist { node { ring0_addr: 2001:db8:50::250 ring1_addr: 2001:db8:60::250 nodeid: 1 } node { ring0_addr: 2001:db8:50::251 ring1_addr: 2001:db8:60::251 nodeid: 2 } } -------------------------------------- Many thanks! Hideo Yamauchi. --- On Sat, 2012/5/26, renayama19661014@xxxxxxxxx <renayama19661014@xxxxxxxxx> wrote: > Hi Andrew, > > Sorry... > > In corosync.conf which I sent, there might be still room for the correction. > I will confirm your opinion next week. > > Many Thanks, > Hideo Yamauchi. > > > > --- On Fri, 2012/5/25, Andrew Beekhof <andrew@xxxxxxxxxxx> wrote: > > > Why the duplication? > > Surely nodeid in totem {} should be enough for corosync to pick the > > right nodelist entry. > > > > On Fri, May 25, 2012 at 11:48 AM, Digimer <lists@xxxxxxxxxx> wrote: > > > With Yamauchi-san's permission to repost, here is the sample config; > > > > > > ======== > > > All right! > > > * Please rearrange the addresses as needed. > > > > > > Step 1) Because corosync did not support private IP address, I added a > > > global address to node beforehand. > > > > > > [root@rh62-coro2-1 ~]# ifconfig eth1 add 2001:db8:50::250/64 > > > [root@rh62-coro2-1 ~]# ifconfig eth2 add 2001:db8:60::250/64 > > > [root@rh62-coro2-2 ~]# ifconfig eth1 add 2001:db8:50::251/64 > > > [root@rh62-coro2-2 ~]# ifconfig eth2 add 2001:db8:60::251/64 > > > > > > Step2) I placed next corosync.conf in two nodes. > > > * rh62-coro2-1 > > > totem { > > > version: 2 > > > secauth: off > > > rrp_mode:active > > > nodeid : 1 > > > interface { > > > ringnumber: 0 > > > bindnetaddr: 2001:db8:50::250 > > > ttl: 1 > > > } > > > interface { > > > ringnumber: 1 > > > bindnetaddr: 2001:db8:60::250 > > > ttl: 1 > > > } > > > transport: udpu > > > } > > > > > > (snip) > > > > > > quorum { > > > provider: corosync_votequorum > > > votes: 1 > > > } > > > > > > nodelist { > > > node { > > > ring0_addr: 2001:db8:50::250 > > > ring1_addr: 2001:db8:60::250 > > > nodeid: 1 > > > } > > > node { > > > ring0_addr: 2001:db8:50::251 > > > ring1_addr: 2001:db8:60::251 > > > nodeid: 2 > > > } > > > } > > > * rh62-coro2-2 > > > totem { > > > version: 2 > > > secauth: off > > > rrp_mode:active > > > nodeid : 2 > > > interface { > > > ringnumber: 0 > > > bindnetaddr: 2001:db8:50::251 > > > ttl: 1 > > > } > > > interface { > > > ringnumber: 1 > > > bindnetaddr: 2001:db8:60::251 > > > ttl: 1 > > > } > > > transport: udpu > > > } > > > (snip) > > > > > > quorum { > > > provider: corosync_votequorum > > > votes: 1 > > > } > > > > > > nodelist { > > > node { > > > ring0_addr: 2001:db8:50::250 > > > ring1_addr: 2001:db8:60::250 > > > nodeid: 1 > > > } > > > node { > > > ring0_addr: 2001:db8:50::251 > > > ring1_addr: 2001:db8:60::251 > > > nodeid: 2 > > > } > > > } > > > > > > Best Regards, > > > Hideo Yamauchi. > > > ======== > > > > > > Thanks for providing this. :) > > > > > > Digimer > > > > > > On 05/24/2012 08:05 PM, Digimer wrote: > > >> Would you mind sharing your configuration? I think having an example in > > >> the archives would be very useful. > > >> > > >> Thanks! > > >> > > >> On 05/24/2012 07:54 PM, renayama19661014@xxxxxxxxx wrote: > > >>> Hi All, > > >>> > > >>> Sorry... > > >>> The problem was settled. > > >>> > > >>> Best Regards, > > >>> Hideo Yamauchi. > > >>> > > >>> --- On Thu, 2012/5/24, renayama19661014@xxxxxxxxx <renayama19661014@xxxxxxxxx> wrote: > > >>> > > >>>> Hi All, > > >>>> > > >>>> We try a test of the IPv6 using corosync2.0. > > >>>> We am going to test it in IPv6 by UCAST communication. > > >>>> > > >>>> transport: udpu > > >>>> > > >>>> I changed corosync.conf for IPv6, but corosync does not start. > > >>>> > > >>>> Please teach a sample of corosync.conf when I use the IPv6. > > >>>> > > >>>> Best Regards, > > >>>> Hideo Yamauchi. > > >>>> _______________________________________________ > > >>>> discuss mailing list > > >>>> discuss@xxxxxxxxxxxx > > >>>> http://lists.corosync.org/mailman/listinfo/discuss > > >>>> > > >>> _______________________________________________ > > >>> discuss mailing list > > >>> discuss@xxxxxxxxxxxx > > >>> http://lists.corosync.org/mailman/listinfo/discuss > > >> > > >> > > > > > > > > > -- > > > Digimer > > > Papers and Projects: https://alteeve.com > > > _______________________________________________ > > > discuss mailing list > > > discuss@xxxxxxxxxxxx > > > http://lists.corosync.org/mailman/listinfo/discuss > > > _______________________________________________ > discuss mailing list > discuss@xxxxxxxxxxxx > http://lists.corosync.org/mailman/listinfo/discuss > _______________________________________________ discuss mailing list discuss@xxxxxxxxxxxx http://lists.corosync.org/mailman/listinfo/discuss