With Yamauchi-san's permission to repost, here is the sample config;
========
All right!
* Please rearrange the addresses as needed.
Step 1) Because corosync did not support private IP address, I added a
global address to node beforehand.
[root@rh62-coro2-1 ~]# ifconfig eth1 add 2001:db8:50::250/64
[root@rh62-coro2-1 ~]# ifconfig eth2 add 2001:db8:60::250/64
[root@rh62-coro2-2 ~]# ifconfig eth1 add 2001:db8:50::251/64
[root@rh62-coro2-2 ~]# ifconfig eth2 add 2001:db8:60::251/64
Step2) I placed next corosync.conf in two nodes.
* rh62-coro2-1
totem {
version: 2
secauth: off
rrp_mode:active
nodeid : 1
interface {
ringnumber: 0
bindnetaddr: 2001:db8:50::250
ttl: 1
}
interface {
ringnumber: 1
bindnetaddr: 2001:db8:60::250
ttl: 1
}
transport: udpu
}
(snip)
quorum {
provider: corosync_votequorum
votes: 1
}
nodelist {
node {
ring0_addr: 2001:db8:50::250
ring1_addr: 2001:db8:60::250
nodeid: 1
}
node {
ring0_addr: 2001:db8:50::251
ring1_addr: 2001:db8:60::251
nodeid: 2
}
}
* rh62-coro2-2
totem {
version: 2
secauth: off
rrp_mode:active
nodeid : 2
interface {
ringnumber: 0
bindnetaddr: 2001:db8:50::251
ttl: 1
}
interface {
ringnumber: 1
bindnetaddr: 2001:db8:60::251
ttl: 1
}
transport: udpu
}
(snip)
quorum {
provider: corosync_votequorum
votes: 1
}
nodelist {
node {
ring0_addr: 2001:db8:50::250
ring1_addr: 2001:db8:60::250
nodeid: 1
}
node {
ring0_addr: 2001:db8:50::251
ring1_addr: 2001:db8:60::251
nodeid: 2
}
}
Best Regards,
Hideo Yamauchi.
========
Thanks for providing this. :)
Digimer
On 05/24/2012 08:05 PM, Digimer wrote:
> Would you mind sharing your configuration? I think having an example in
> the archives would be very useful.
>
> Thanks!
>
> On 05/24/2012 07:54 PM, renayama19661014@xxxxxxxxx wrote:
>> Hi All,
>>
>> Sorry...
>> The problem was settled.
>>
>> Best Regards,
>> Hideo Yamauchi.
>>
>> --- On Thu, 2012/5/24, renayama19661014@xxxxxxxxx <renayama19661014@xxxxxxxxx> wrote:
>>
>>> Hi All,
>>>
>>> We try a test of the IPv6 using corosync2.0.
>>> We am going to test it in IPv6 by UCAST communication.
>>>
>>> transport: udpu
>>>
>>> I changed corosync.conf for IPv6, but corosync does not start.
>>>
>>> Please teach a sample of corosync.conf when I use the IPv6.
>>>
>>> Best Regards,
>>> Hideo Yamauchi.
>>> _______________________________________________
>>> discuss mailing list
>>> discuss@xxxxxxxxxxxx
>>> http://lists.corosync.org/mailman/listinfo/discuss
>>>
>> _______________________________________________
>> discuss mailing list
>> discuss@xxxxxxxxxxxx
>> http://lists.corosync.org/mailman/listinfo/discuss
>
>
--
Digimer
Papers and Projects: https://alteeve.com
_______________________________________________
discuss mailing list
discuss@xxxxxxxxxxxx
http://lists.corosync.org/mailman/listinfo/discuss
