Hi all,
I've got CentOS 5.3 installed on two nodes (simple two node cluster).
On this, I've got a DRBD partition running cluster aware LVM. I use this
to host VMs under Xen.
I've got a problem where I am trying to use eth0 as a back channel
for the VMs on either node via a firewall VM. The network setup on each
node is:
eth0: back channel, IPMI only connected to an internal network.
eth1: dedicated DRBD link.
eth2: Internet-facing interface.
I want to get eth0 and eth2 under Xen's networking but the default
config was to leave eth0 alone. Specifically, the
convirt-xen-multibridge is set to:
"$dir/network-bridge" "$@" vifnum=0 netdev=peth0 bridge=xenbr0
When I change this to:
"$dir/network-bridge" "$@" vifnum=0 netdev=eth0 bridge=xenbr0
One of the nodes will soon fence the other, and when it comes back up
it fences the first. Eventually one node stays up and constantly fences
the other.
The node that survives prints this to repeatedly to the log just
before it is fenced:
Oct 31 00:27:21 vsh02 openais[3133]: [TOTEM] FAILED TO RECEIVE
Oct 31 00:27:21 vsh02 openais[3133]: [TOTEM] entering GATHER state from 6.
And the node that stays up prints this:
Oct 31 00:35:47 vsh03 openais[3237]: [TOTEM] The token was lost in the
OPERATIONAL state.
Oct 31 00:35:47 vsh03 openais[3237]: [TOTEM] Receive multicast socket
recv buffer size (288000 bytes).
Oct 31 00:35:47 vsh03 openais[3237]: [TOTEM] Transmit multicast socket
send buffer size (262142 bytes).
Oct 31 00:35:47 vsh03 openais[3237]: [TOTEM] entering GATHER state from 2.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] entering GATHER state from 0.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] Creating commit token
because I am the rep.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] Saving state aru 2c high
seq received 2c
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] Storing new sequence id for
ring 108
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] entering COMMIT state.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] entering RECOVERY state.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] position [0] member
10.255.135.3:
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] previous ring seq 260 rep
10.255.135.2
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] aru 2c high delivered 2c
received flag 1
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] Did not need to originate
any messages in recovery.
Oct 31 00:35:51 vsh03 openais[3237]: [TOTEM] Sending initial ORF token
Oct 31 00:35:51 vsh03 openais[3237]: [CLM ] CLM CONFIGURATION CHANGE
Oct 31 00:35:51 vsh03 openais[3237]: [CLM ] New Configuration:
Oct 31 00:35:51 vsh03 kernel: dlm: closing connection to node 1
Oct 31 00:35:51 vsh03 fenced[3256]: vsh02.domain.com not a cluster
member after 0 sec post_fail_delay
Oct 31 00:35:51 vsh03 openais[3237]: [CLM ] r(0) ip(10.255.135.3)
Oct 31 00:35:51 vsh03 fenced[3256]: fencing node "vsh02.domain.com"
If I leave it long enough, the failed node (vsh02 in this case),
stops getting fenced but the Xen networking doesn't come up.
Specifically, no vifX.Y, xenbrX or other devices get created.
Any idea what might be going on? I really need to get eth0
virtualized so that I can get routing to work.
Thanks!
Madi
--
Linux-cluster mailing list
Linux-cluster@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/linux-cluster
