Anyone is successfully using it? I'm testing it with a clariion storage frame on RHEL 5.3, and as soon as I enable scsi_reserve, multipath starts failing and a path goes good and bad in a loop and scsi fencing fails sometimes, should I configure in a specific way multipath.conf?: Jun 10 23:31:58 rmamseslab07 multipathd: mpath0: remaining active paths: 3 Jun 10 23:32:00 rmamseslab07 kernel: sd 1:0:0:1: reservation conflict Jun 10 23:32:00 rmamseslab07 kernel: sd 1:0:0:1: SCSI error: return code = 0x00000018 Jun 10 23:32:00 rmamseslab07 kernel: end_request: I/O error, dev sdm, sector 79 Jun 10 23:32:00 rmamseslab07 kernel: device-mapper: multipath: Failing path 8:192. Jun 10 23:32:00 rmamseslab07 multipathd: 8:192: mark as failed Jun 10 23:32:00 rmamseslab07 multipathd: mpathquorum: remaining active paths: 3 Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: add map (uevent) Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: devmap already registered Jun 10 23:32:00 rmamseslab07 multipathd: sdm: emc_clariion_checker: Path healthy Jun 10 23:32:00 rmamseslab07 multipathd: 8:192: reinstated Jun 10 23:32:00 rmamseslab07 multipathd: mpathquorum: remaining active paths: 4 Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: add map (uevent) Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: devmap already registered Jun 10 23:32:02 rmamseslab07 multipathd: sdl: emc_clariion_checker: Path healthy Jun 10 23:32:02 rmamseslab07 multipathd: 8:176: reinstated Jun 10 23:32:02 rmamseslab07 multipathd: mpath0: remaining active paths: 4 Jun 10 23:32:02 rmamseslab07 multipathd: dm-9: add map (uevent) Jun 10 23:32:02 rmamseslab07 multipathd: dm-9: devmap already registered Jun 10 23:32:03 rmamseslab07 kernel: sd 1:0:0:0: reservation conflict Jun 10 23:32:03 rmamseslab07 kernel: sd 1:0:0:0: SCSI error: return code = 0x00000018 Jun 10 23:32:03 rmamseslab07 kernel: end_request: I/O error, dev sdl, sector 25256 Jun 10 23:32:03 rmamseslab07 kernel: device-mapper: multipath: Failing path 8:176. Jun 10 23:32:03 rmamseslab07 multipathd: dm-9: add map (uevent) Jun 10 23:32:03 rmamseslab07 multipathd: dm-9: devmap already registered Jun 10 23:32:03 rmamseslab07 multipathd: 8:176: mark as failed Jun 10 23:32:03 rmamseslab07 multipathd: mpath0: remaining active paths: 3 -----Original Message----- From: linux-cluster-bounces@xxxxxxxxxx [mailto:linux-cluster-bounces@xxxxxxxxxx] On Behalf Of Ryan O'Hara Sent: Wednesday, June 10, 2009 9:18 PM To: linux clustering Subject: Re: fence_scsi support in multipath env in RHEL5.3 On Wed, Jun 10, 2009 at 02:11:21PM +0530, Rajeev P wrote: > I wanted to know if fence_scsi is supported in a multipath environment for > RHEL5.3 release. Yes, it is supported. > In earlier releases of RHEL5 fence_scsi was not supported in a multipath > environment for RHEL5.3 release. If I am not wrong, this was because the > DM-MPIO driver forwarded the registration/unregistration commands on only on > one of the physical paths of a LUN. Ideally it should have passed the > commands on all physical paths. > > For RHEL5.3, is this issue resolved so that I can fence_scsi in multipath > environment. > > Thanks in advance. > > Rajeev > -- > Linux-cluster mailing list > Linux-cluster@xxxxxxxxxx > https://www.redhat.com/mailman/listinfo/linux-cluster -- Linux-cluster mailing list Linux-cluster@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/linux-cluster -- Linux-cluster mailing list Linux-cluster@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/linux-cluster
