Re: Howto? Remove volumes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Anyone have any additional thoughts on this? It's a left over volume after I 
zoned everything off.

Mike

---
SCSI subsystem initialized
QLogic Fibre Channel HBA Driver
qla2200 0000:00:11.0: Found an ISP2200, irq 11, iobase 0xe0816000
qla2200 0000:00:11.0: Configuring PCI space...
qla2200 0000:00:11.0: Configure NVRAM parameters...
qla2200 0000:00:11.0: Verifying loaded RISC code...
qla2200 0000:00:11.0: LIP reset occured (0).
qla2200 0000:00:11.0: Waiting for LIP to complete...
qla2200 0000:00:11.0: LOOP UP detected (1 Gbps).
qla2200 0000:00:11.0: Topology - (F_Port), Host Loop address 0xffff
scsi0 : qla2xxx
qla2200 0000:00:11.0:
 QLogic Fibre Channel HBA Driver: 8.01.04-d7
  QLogic QLA22xx -
  ISP2200: PCI (33 MHz) @ 0000:00:11.0 hdma-, host#=0, fw=2.02.08 TP
  Vendor: MYLEX     Model: DACARMRB PSEUDO   Rev: 7775
  Type:   Direct-Access                      ANSI SCSI revision: 02
qla2200 0000:00:11.0: scsi(0:0:0:0): Enabled tagged queuing, queue depth 16.
sda: Unit Not Ready, sense:
Current : sense key Illegal Request
Additional sense: Logical unit not supported
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Illegal Request
Additional sense: Logical unit not supported
sda: asking for cache data failed
sda: assuming drive cache: write through
sda: Unit Not Ready, sense:
Current : sense key Illegal Request
Additional sense: Logical unit not supported
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
Current sd: sense key Illegal Request
Additional sense: Logical unit not supported
sda: asking for cache data failed
sda: assuming drive cache: write through
 sda:end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
end_request: I/O error, dev sda, sector 0
Buffer I/O error on device sda, logical block 0
 unable to read partition table
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: MYLEX     Model: DACARMRB          Rev: 7775
  Type:   Direct-Access                      ANSI SCSI revision: 02
qla2200 0000:00:11.0: scsi(0:0:0:2): Enabled tagged queuing, queue depth 16.
SCSI device sdb: 997449728 512-byte hdwr sectors (510694 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 997449728 512-byte hdwr sectors (510694 MB)
SCSI device sdb: drive cache: write back
 sdb:
Attached scsi disk sdb at scsi0, channel 0, id 0, lun 2




--
Linux-cluster mailing list
Linux-cluster@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/linux-cluster

[Index of Archives]     [Corosync Cluster Engine]     [GFS]     [Linux Virtualization]     [Centos Virtualization]     [Centos]     [Linux RAID]     [Fedora Users]     [Fedora SELinux]     [Big List of Linux Books]     [Yosemite Camping]

  Powered by Linux