Casey,
OR, is there a way to continue on with new data syncing (incremental) as the full sync catches up, as the full sync will take a long time, and no new incremental data is being replicated.
-Chris
On Wednesday, November 20, 2024 at 03:30:40 PM MST, Christopher Durham <caduceus42@xxxxxxx> wrote:
Casey,
Thanks for your response. So is there a way to abandon a full sync and just move on with an incremental from the time you abandon the full sync?
-Chris
On Wednesday, November 20, 2024 at 12:29:26 PM MST, Casey Bodley <cbodley@xxxxxxxxxx> wrote:
On Wed, Nov 20, 2024 at 2:10 PM Christopher Durham <caduceus42@xxxxxxx> wrote:
>
> Ok,
> Source code review reveals that full sync is marker based and sync errors within a marker group *suggest* that data within the marker isre-checked, (I may be wrong about this, but that is consistent with my 304 errors below). I do however, have the folllowing question:
> Is there a way to otherwise abort a full sync of a bucket (as a result of radosgw-admin bucket sync init --bucket <bucket> and bucket sync run (or restart of radosgw),and have it just do incremental sync from then on (yes, having the objects not be the same on both sides prior to the 'restart' of an incremental sync.
> Would radosgw-admin bucket sync disable --bucket <bucket> followed by radosgw-admin bucket sync enable --bucket <bucket> do this? Or would that do anotherfull sync and not an incremental?
'bucket sync enable' does start a new full sync (to catch objects that
were uploaded since 'bucket sync disable')
Thanks
> -Chris
>
> On Thursday, November 14, 2024 at 04:18:34 PM MST, Christopher Durham <caduceus42@xxxxxxx> wrote:
>
> Hi,
> I have heard nothing on this, but have done some more research.
> Again, both sides of a multisite s3 configuration are ceph 18.2.4 on Rocky 9.
> For a given bucket, there are thousands of 'missing' objects. I did:
> radosgw-admin bucket sync init --bucket <bucket> --src-zone <other side zone>sync starts after I restart a radosgw on the source zone that has a sync thread.
> But based on number and size of objects needing replication, it NEVER finishes, as more objects are created as I am going.I may need to increase the number of radosgw and or the sync threads.
>
> What I have discovered that if a radosgw on the side with missing objects is restarted, all sycing starts over!In other words, it starts polling each object, getting a 304 error in the radosgw log on the server on the multisite that has the missing objects.It *appears* to do this sequential object scan in lexographic order of object and/or prefix name, although I cannot be sure.
>
> So some questions:
> 1. Is there a recommendation/rule of thumb/formula for the number of radosgws/syncthreads/ etc based on number of objects, buckets, bandwidth, etc?2. Why does the syncing restart for a bucket when a radosgw is restarted? Is there a way to tell it to restart where it left off as opposed to starting over?There may be reasons to restart a bucket sync if a radosgw restarts, but there should be a way to checkpoint/force it to not restart/start where left off, etc.3. Is there a way to 'abort' the sync and cause the bucket to think it is up to date and only replicate new objects from the time it was marked up to date?
> Thanks for any information
> -Chris
>
>
>
> On Friday, November 8, 2024 at 03:45:05 PM MST, Christopher Durham <caduceus42@xxxxxxx> wrote:
>
>
> I have a 2-site multisite configuration on cdnh 18.2.4 on EL9.
> After system updates, we discovered that a particular bucket had several thousand objects missing, which the other side had. Newly created objects were being replicated just fine.
>
> I decided to 'restart' syncing that bucket. Here is what I did
> On the side with misisng objects:
> > radosgw-admin bucket sync init --bucket <bucketname> --src-zone <zone>
>
> I restarted the radosgw set up to do the sync thread on the same zone as I ran the radosgw-admin command.
>
> Logs on the radosgw src-zone side show GETs with http code 200 for objects that do not exist on the side with missing objects, and GETs with http 304 for objects that already exist on the side with missing objects.
> So far, so good.
> As I said, the bucket is active. So on the src-zone side, data is continually being written to /prefixA/../../ There is also data being written to /prefixB/../../
> prefixA/ comes lexographically before prefixB/
> What happens is that all the 304s happen as it scans the bucket, then starts pulling with GETs and http 200s for the objects the side doing the sync doesnt have. This is on /prefixA. When it 'caches up' with alldata in /prefixA at the moment, the sync seems to START OVER with /prefixA, giving 304s for everything that existed in the bucket up to the moment it caught up, then doing GETs with 200s for the remainingnewer objects. This happens over and over again. It NEVER gets to /prefixB. So it seems to be periodically catching up to /prefixA, but never going on to /prefixB that is also being written to
> There are 1.2 million objects in this bucket, with about 35 TiB in the bucket.
> There is a lifecycle expiration happening of 60 days.
> Any thoughts would be appreciated.
> -Chris
>
>
>
> _______________________________________________
> ceph-users mailing list -- ceph-users@xxxxxxx
> To unsubscribe send an email to ceph-users-leave@xxxxxxx
>
_______________________________________________
ceph-users mailing list -- ceph-users@xxxxxxx
To unsubscribe send an email to ceph-users-leave@xxxxxxx
_______________________________________________
ceph-users mailing list -- ceph-users@xxxxxxx
To unsubscribe send an email to ceph-users-leave@xxxxxxx
