Hi Will,
All our clusters with noout flag by default, since cluster birth. The reasons:
* if rebalance will starts due EDAC or SFP degradation, is faster to fix the issue via DC engineers and put node back to work
* noout prevents unwanted OSD's fills and the run out of space => outage of services
* OSD down (broken disk) Prometeus alert will be resolved without noout - after OSD will be marked out. Because UP state of OSD in metrics world is expression of (in + up). We need "fire alert" for humans, for disk replacement 🙂
Also hope this helps!
k
Sent from my iPhone
> On 16 Feb 2023, at 06:30, William Konitzer <wkonitzer@xxxxxxxxxxxx> wrote:
> Hi Dan,
>
> I appreciate the quick response. In that case, would something like this be better, or is it overkill!?
>
> 1. ceph osd add-noout osd.x #mark out for recovery operations
> 2. ceph osd add-noin osd.x #prevent rebalancing onto the OSD
> 3. kubectl -n rook-ceph scale deployment rook-ceph-osd-<ID>-* --replicas=0 #disable OSD
> 4. ceph osd down osd.x #prevent it from data placement and recovery operations
> 5. Upgrade the firmware on OSD
> 6. ceph osd up osd.x
> 7. kubectl -n rook-ceph scale deployment rook-ceph-osd-<ID>-* --replicas=1
> 8. ceph osd rm-noin osd.x
> 9. ceph osd rm-noout osd.x
>
> Thanks,
> Will
>
>
>> On Feb 15, 2023, at 5:05 PM, Dan van der Ster <dvanders@xxxxxxxxx> wrote:
>>
>> Sorry -- Let me rewrite that second paragraph without overloading the
>> term "rebalancing", which I recognize is confusing.
>>
>> ...
>>
>> In your case, where you want to perform a quick firmware update on the
>> drive, you should just use noout.
>>
>> Without noout, the OSD will be marked out after 5 minutes and objects
>> will be re-replicated to other OSDs -- those degraded PGs will move to
>> "backfilling" state and copy the objects on new OSDs.
>>
>> With noout, the cluster won't start backfilling/recovering, but don't
>> worry -- this won't block IO. What happens is the disk that is having
>> its firmware upgraded will be marked "down", and IO will be accepted
>> and logged by its peers, so that when the disk is back "up" it can
>> replay ("recover") those writes to catch up.
>>
>>
>> The norebalance flag only impacts data movement for PGs that are not
>> degraded -- no OSDs are down. This can be useful to pause backfilling
>> e.g. when you are adding or removing hosts to a cluster.
>>
>> -- dan
>>
>> On Wed, Feb 15, 2023 at 2:58 PM Dan van der Ster <dvanders@xxxxxxxxx> wrote:
>>> Hi Will,
>>> There are some misconceptions in your mail.
>>> 1. "noout" is a flag used to prevent the down -> out transition after
>>> an osd is down for several minutes. (Default 5 minutes).
>>> 2. "norebalance" is a flag used to prevent objects from being
>>> backfilling to a different OSD *if the PG is not degraded*.
>>> In your case, where you want to perform a quick firmware update on the
>>> drive, you should just use noout.
>>> Without noout, the OSD will be marked out after 5 minutes and data
>>> will start rebalancing to other OSDs.
>>> With noout, the cluster won't start rebalancing. But this won't block
>>> IO -- the disk being repaired will be "down" and IO will be accepted
>>> and logged by it's peers, so that when the disk is back "up" it can
>>> replay those writes to catch up.
>>> Hope that helps!
>>> Dan
>>> On Wed, Feb 15, 2023 at 1:12 PM <wkonitzer@xxxxxxxxxxxx> wrote:
>>>> Hi,
>>>> We have a discussion going on about which is the correct flag to use for some maintenance on an OSD, should it be "noout" or "norebalance"? This was sparked because we need to take an OSD out of service for a short while to upgrade the firmware.
>>>> One school of thought is:
>>>> - "ceph norebalance" prevents automatic rebalancing of data between OSDs, which Ceph does to ensure all OSDs have roughly the same amount of data.
>>>> - "ceph noout" on the other hand prevents OSDs from being marked as out-of-service during maintenance, which helps maintain cluster performance and availability.
>>>> - Additionally, if another OSD fails while the "norebalance" flag is set, the data redundancy and fault tolerance of the Ceph cluster may be compromised.
>>>> - So if we're going to maintain the performance and reliability we need to set the "ceph noout" flag to prevent the OSD from being marked as OOS during maintenance and allow the automatic data redistribution feature of Ceph to work as intended.
>>>> The other opinion is:
>>>> - With the noout flag set, Ceph clients are forced to think that OSD exists and is accessible - so they continue sending requests to such OSD. The OSD also remains in the crush map without any signs that it is actually out. If an additional OSD fails in the cluster with the noout flag set, Ceph is forced to continue thinking that this new failed OSD is OK. It leads to stalled or delayed response from the OSD side to clients.
>>>> - Norebalance instead takes into account the in/out OSD status, but prevents data rebalance. Clients are also aware of the real OSD status, so no requests go to the OSD which is actually out. If an additional OSD fails - only the required temporary PG are created to maintain at least 2 existing copies of the same data (well, generally it is set by the pool min size).
>>>> The upstream docs seem pretty clear that noout should be used for maintenance (https://docs.ceph.com/en/quincy/rados/troubleshooting/troubleshooting-osd/), but the second opinion strongly suggests that norebalance is actually better and the Ceph docs are out of date.
>>>> So what is the feedback from the wider community?
>>>> Thanks,
>>>> Will
>>>> _______________________________________________
>>>> ceph-users mailing list -- ceph-users@xxxxxxx
>>>> To unsubscribe send an email to ceph-users-leave@xxxxxxx
> _______________________________________________
> ceph-users mailing list -- ceph-users@xxxxxxx
> To unsubscribe send an email to ceph-users-leave@xxxxxxx
_______________________________________________
ceph-users mailing list -- ceph-users@xxxxxxx
To unsubscribe send an email to ceph-users-leave@xxxxxxx
