client0 fsid <hex number>, and
mon0 <ip-addr>:6789 session established
ceph -s -m ceph-1 -k ceph.client.admin.keyring, returns:
health HEALTH_OK
monmap e1: 1 mons at {ceph-1=155.53.104.100:6789/0}, election epoch 2, quorum 0 ceph-1
osdmap e15: 2 osds: 2 up, 2 in
pgmap v1134: 192 pgs: 192 active+clean; 197 MB data, 14166 MB used, 1242 GB / 1323 GB avail
mdsmap e527: 1/1/1 up {0=ceph-1=up:active}
On Tue, Jul 16, 2013 at 10:37 AM, Gregory Farnum <greg@xxxxxxxxxxx> wrote:
On Tue, Jul 16, 2013 at 10:29 AM, Hariharan Thantry <thantry@xxxxxxxxx> wrote:Is there any output in dmesg? And what's the output of "ceph -s"?
> Thanks, now I get a different error:
>
> mount error 12 = cannot allocate memory.
>
> My ceph-client and the storage cluster are at the same version, though I'm
> running the client inside a VM (VirtualBox)...with 1536M of RAM space, with
> an 8GB hard disk. Shouldn't this be sufficient?
>
> P.S. Maybe you could update the page here:
> http://ceph.com/docs/master/start/quick-cephfs/#create-a-secret-file, to
> install ceph-fs-common & ceph-fuse (for fuse clients)
-Greg
Software Engineer #42 @ http://inktank.com | http://ceph.com
>
> Thanks,
> Hari
>
>
>
> On Tue, Jul 16, 2013 at 10:07 AM, Gregory Farnum <greg@xxxxxxxxxxx> wrote:
>>
>> You don't have mount.ceph installed, and there's some translation that
>> needs to be done in userspace before the kernel sees the mount which
>> isn't happening. On Debian it's in the ceph-fs-common package.
>> -Greg
>> Software Engineer #42 @ http://inktank.com | http://ceph.com
>>
>>
>> On Tue, Jul 16, 2013 at 10:02 AM, Hariharan Thantry <thantry@xxxxxxxxx>
>> wrote:
>> > While trying to execute these steps in the ceph users guide, I get
>> > libceph
>> > errors
>> >
>> > no secret set (for auth_x protocol)
>> >
>> > error -22 on auth protocol 2 init
>> >
>> > Also, when providing the authentication keys (Step #3 below), I get the
>> > following error:
>> >
>> > bad option at secretfile=admin.secret
>> >
>> > Any ideas where I could be going wrong? The health check reports OK.
>> >
>> >
>> > Mount Ceph FS as a kernel driver.
>> >
>> > sudo mkdir /mnt/mycephfs
>> > sudo mount -t ceph {ip-address-of-monitor}:6789:/ /mnt/mycephfs
>> >
>> > The Ceph Storage Cluster uses authentication by default. Specify a user
>> > name
>> > and the secretfile you created in the Create a Secret File section. For
>> > example:
>> >
>> > sudo mount -t ceph 192.168.0.1:6789:/ /mnt/mycephfs -o
>> > name=admin,secretfile=admin.secret
>> >
>> >
>> > _______________________________________________
>> > ceph-users mailing list
>> > ceph-users@xxxxxxxxxxxxxx
>> > http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
>> >
>
>
_______________________________________________ ceph-users mailing list ceph-users@xxxxxxxxxxxxxx http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
