Hi, On Sun, 2011-04-17 at 17:37 -0700, Colin McCabe wrote: > I don't think we want log to syslog to be in the sample configuration > file. Maybe we could include it, but commented out. Most users will > want to enable logging to a file or to syslog, but not both. > Ah yes, I see. The syslog was my bad, my idea was to have it commented out, but have it just as a reference in there, didn't check that good enough. But right now you can only disable logging to a file by setting: log file = That seems a bit odd, "log file = false" would be easier. Imho the current sample config is still broken. Monitors names are only numeric, shouldn't we encourage users to give them a full name? mon.alpha, mon.beta, etc? osd journal = /data/osd$id/journal That will result in: /data/osd0/journal When the osd's name is osd.0, that also seems a bit weird, would $name be better there then osd$id (see my patch). Same goes for data btw Wido > Colin > > > On Sun, Apr 17, 2011 at 2:32 AM, Wido den Hollander <wido@xxxxxxxxx> wrote: > > > > Signed-off-by: Wido den Hollander <wido@xxxxxxxxx> > > --- > > src/sample.ceph.conf | 23 +++++++++++++---------- > > 1 files changed, 13 insertions(+), 10 deletions(-) > > > > diff --git a/src/sample.ceph.conf b/src/sample.ceph.conf > > index bb874e7..31674f6 100644 > > --- a/src/sample.ceph.conf > > +++ b/src/sample.ceph.conf > > @@ -24,6 +24,9 @@ > > ; set up pid files > > pid file = /var/run/ceph/$name.pid > > > > + ; Also log to syslog > > + log to syslog = true > > + > > ; monitors > > ; You need at least one. You need at least three if you want to > > ; tolerate any node failures. Always create an odd number. > > @@ -37,15 +40,15 @@ > > ;debug paxos = 20 > > ;debug auth = 20 > > > > -[mon0] > > +[mon.alpha] > > host = alpha > > mon addr = 192.168.0.10:6789 > > > > -[mon1] > > +[mon.beta] > > host = beta > > mon addr = 192.168.0.11:6789 > > > > -[mon2] > > +[mon.gamma] > > host = gamma > > mon addr = 192.168.0.12:6789 > > > > @@ -70,16 +73,16 @@ > > ; Define as many as you like. > > [osd] > > ; This is where the btrfs volume will be mounted. > > - osd data = /data/osd$id > > + osd data = /data/$name > > > > ; Ideally, make this a separate disk or partition. A few > > ; hundred MB should be enough; more if you have fast or many > > ; disks. You can use a file under the osd data dir if need be > > - ; (e.g. /data/osd$id/journal), but it will be slower than a > > + ; (e.g. /data/$name/journal), but it will be slower than a > > ; separate disk or partition. > > > > ; This is an example of a file-based journal. > > - osd journal = /data/osd$id/journal > > + osd journal = /data/$name/journal > > osd journal size = 1000 ; journal size, in megabytes > > > > ; osd logging to debug osd issues, in order of likelihood of being > > @@ -89,7 +92,7 @@ > > ;debug filestore = 20 > > ;debug journal = 20 > > > > -[osd0] > > +[osd.0] > > host = delta > > > > ; if 'btrfs devs' is not specified, you're responsible for > > @@ -98,14 +101,14 @@ > > ; usually fine for basic testing). > > btrfs devs = /dev/sdx > > > > -[osd1] > > +[osd.1] > > host = epsilon > > btrfs devs = /dev/sdy > > > > -[osd2] > > +[osd.2] > > host = zeta > > btrfs devs = /dev/sdx > > > > -[osd3] > > +[osd.3] > > host = eta > > btrfs devs = /dev/sdy > > -- > > 1.7.0.4 > > > > -- > > To unsubscribe from this list: send the line "unsubscribe ceph-devel" in > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > -- To unsubscribe from this list: send the line "unsubscribe ceph-devel" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
