On Sun, Jun 6, 2010 at 3:14 PM, John Thomas
<gmane-2006-04-16@xxxxxxxxxxxx> wrote:
>> It sounds like you have a non-standard driver that is not compatible
>> with the latest kernel.
> Hmm, using nvidia video driver from ELRepo and I don't remember anything
> else. I tried without the nvidia driver, but same problem.
>
>> Can you post more details about the machine, say info from a working
>> kernel? Things like configuration, drivers, etc.
> Hmm, not sure how to do that. How about this:
> CentOS55[root@home ~]# lspci
> 00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
> 00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
> 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management
> (rev a1)
> 00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
> 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
> 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0
> Controller (rev a2)
> 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb
> AC'97 Audio Controller (rev a1)
> 00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller
> (v2.5) (rev a2)
> 00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI
> Bridge (rev a2)
> 00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge
> (rev a2)
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> HyperTransport Technology Configuration
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Address Map
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> DRAM Controller
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Miscellaneous Control
> 01:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800
> GT] (rev a1)
> 02:08.0 RAID bus controller: 3ware Inc 9xxx-series SATA-RAID
> 02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire
> II(M)] IEEE 1394 OHCI Controller (rev 46)
> 02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
> Gigabit Ethernet (rev 10)
>
> CentOS55[root@home ~]# lsusb
> Bus 002 Device 001: ID 0000:0000
> Bus 003 Device 001: ID 0000:0000
> Bus 001 Device 001: ID 0000:0000
> Bus 001 Device 002: ID 11b0:6888 ATECH FLASH TECHNOLOGY
>
I'd run the 64-bit distro on an Opteron, not PAE or 32-bit. That
shouldn't make a difference, but....
Have you checked your /lib/modules directories for non-standard
drivers? If there are any, you might try disabling them and if that
works, put them back one at a time to see which one kills it.
I haven't done much with ELREPO, but I use the rpmforge nVidia driver
for my video card (a cheapo GeForce 7200gs) and it doesn't give me any
problems at all.
Do you know which motherboard you have? I doubt that this would be
it, but it doesn't hurt to check. Sometimes you need to turn on or
off certain switches (mine's an ECS GeForce 6100PM-M2, and I have to
turn off APIC because the motherboard goes haywire with it enabled).
I'd expect this to have shown up in earlier kernels.
You might see if Dell is any help....
Anyone else?
mhr
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
