Also, on the procedure mentioned in the link, I am confused about the
need to run:
rpmbuild -bb --target=`uname -m` kernel-2.6.spec 2> build-err.log | tee
build-out.log
after menuconfig... I tend to believe that I need to do make all then
make modules and make install after reconfiguring the menuconfig. but I
did not find that in the wiki link. Could that be a reason? upon
attempting to build the new kernel, I get the following:
make[1]: *** No rule to make target `init/main.o', needed by
`init/built-in.o'. Stop.
make: *** [init] Error 2
Is it because I do not have the complete source tree there? How can I
verfiry that I have the complete kernel source tree?
Yahia Tachwali wrote:
Thank you very much for the link.. I have built a new bootable kernel
2.6.9-67 on my machine. However I still have a problem :(
During the installation at "make menuconfig" stage after "make
oldconfig" I have added the generic HDLC package with synchronous PPP
support and saved the new config then run
rpmbuild -bb --target=`uname -m` kernel-2.6.spec 2> build-err.log |
tee build-out.log.
After reboot, I rechecked the menuconfig to make sure that the HDLC
setting is there. I am not sure if this setting took effect or I have
to make modules or build something else. So how would I know that the
HDLC package is availalbe and built in?
To elaborate more on the reasons behind this HDLC package, I am trying
to build a device driver that asks for HDLC support. upon building the
driver, I get the following warnings:
Building modules, stage 2.
MODPOST
*** Warning: "unregister_hdlc_device"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
*** Warning: "hdlc_ioctl"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
*** Warning: "hdlc_open"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
*** Warning: "register_hdlc_device"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
*** Warning: "hdlc_close"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
*** Warning: "alloc_hdlcdev"
[/home/DS3/wanPTMC-256T3_2_0B/driver/wan256t3.ko] undefined!
Therefore, I am suspecting that I need the HDLC package available. I
would be extremely thankful for anybody who can help me in this
problem. Am I going into the wrong direction?
jancio_wodnik@xxxxx wrote:
Johnny Hughes pisze:
jancio_wodnik@xxxxx wrote:
Yahia Tachwali pisze:
Hello folks,
Hi. It is request for it to add this in kernel for centosplus, look
at this: http://bugs.centos.org/view.php?id=3019
I am trying to add HDLC module support in the menuconfig. However,
I am facing difficulties in rebuilding the kernel and modules. My
main objective is to get the HDLC supported in kernel 2.6.9. I
have a CentOS 4.4 with kernel 2.6.9.42. I need help in finding the
best way to add the HDLC support whether through getting an RPM
package for it or refering me to the right procedure in rebuilding
the kernel.
Thank you very much in advance for your help.
No problem.
That request was for CentOS-5, not CentOS-4 :D
? I can see: Category: [CentOS-4] kernel-centosplus My request was
exactly for centos 4 branch, but for 5 is good too. So, can i count
for You to make it posible in centos4 to support hdlc ?
HDLC was added to the CentOS-5 plus kernel for the latest version.
------------------------------------------------------------------------
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
------------------------------------------------------------------------
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
