CentOS List wrote:
CentOS List wrote:
CentOS List wrote:
I am running raid 1 on a centos 4.4. One of the harddisk (sda1)
failed. How can i carry on running the server using only sda2?
Generate a grub floppy and use that to load the grub menu from
the sdb (probably now sda) disk.
If you are really talking about sda1 and sda2, those are
partitions on the same disk.
Is there a detail step by step howto? The raid 1 has no LVM. just
md0, md1 and md2. md0 is /boot, md1 is swap and md2 is the
storage. I had replace sba with a new disk. I tried to boot up
and it says kernel panic. How am i going to reconstruct the raid
and sync sdb to sda?
It might be easier to swap the old sdb into the sda position so
you'll boot from it, but you should also be able to boot the
install cd with
If swapped and booted, and got a kernel panic error.
'linux rescue' at the boot prompt, let it detect and mount your
system (which will be the 'broken' raid devices with their single
members),
If i use linux rescue, The 3 mds I created are gone. /cat
/proc/mdstat says Personalitlies: [raid0] [raid1] [raid5] [raid6],
no longer Personalities : [raid1]
Perhaps your raid wasn't really working the way you thought before.
From the rescue boot, does fdisk show the 3 partitions on the old
disk with type 'fd'? Can you mount the old /boot and / partitions
somewhere by hand? You should be able to do this with the /dev/sda1
and /dev/sda3 device names if the md devices aren't detected at boot.
cat /proc/partitions still shows me the 3 partitions.
Does fdisk say that they are type 'fd'(raid autodetect)?
I actually copied /boot to the "replaced disk" and it is able to boot
up, but without any filesystem, so i guess the boot is still intact.
So do i need to mount /boot and /?
If you can get the original partitions to be detected as their md
devices you should fdisk matching partitions on the replacement disk,
then 'mdadm --add ...' to add them and they will automatically sync up.
mdadm --create --verbose /dev/md0 --level=1 --raid-devices=2 /dev/sda1
/dev/sdb1
mdadm --create --verbose /dev/md1 --level=1 --raid-devices=2 /dev/sda2
/dev/sdb2
mdadm --create --verbose /dev/md2 --level=1 --raid-devices=2 /dev/sda3
/dev/sdb3
If you already had raid devices on one of the disks you should not have
had to --create them again. The original ones should have been detected
and you should have been able to --add new matching partitions.
After that i reboot and got the kernel panic again.
md: considering sdb1
md: adding sdb1
md: created md0
md: bind<sda1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE
md: autodetcting RAID arrays
md:mautorun ...
Creating root device
Mounting root filesystem
switching to new root
switchroot: mount failed: 22
umount /unitrd/dev failed: 2
Kernel panic
When you --create a new raid it will start to sync the mirrors. It may
have done this the wrong direction, overwriting your old contents. Can
you still do a rescue mode boot, mount /dev/sda3 (or sdb3 if the old
drive is in the 2nd position) and see the contents?
--
Les Mikesell
lesmikesell@xxxxxxxxx
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
