Al Sparks wrote:
On 2/16/07, Al Sparks <data345@xxxxxxxxx> wrote:
Al Sparks spake the following on 2/15/2007 6:33 PM:
Al Sparks spake the following on 2/15/2007 4:44 PM:
One of the images (in Nahant) is to boot off the CD and install
from the network.
That should work BUT I've only used it to get the entire ks file
off the LAN. Booting from a CD is quick and easy (provided you
have a CD drive as in this instance).
Probably the %include will work fairly easily if the original ks file's
obtained via NFS; otherwise I suspect you'll need to do the mount;
in %pre
How would I access the whole ks.cfg file on an nfs w/o dhcp?
That would be ideal.
=== Al
Assign an ip address during the boot process, and have everything
referenced by ip address, instead of names.
At the boot prompt, I did the following:
linux ksdevice=eth0 ip=10.254.254.125
netmask=255.255.255.0 gateway=10.254.254.1
dns=10.1.1.21 ks=nfs:10.254.242.33:/vol/updts/staging/CentOS_4.3/ks.cfg
I get a blue screen with
"Welcome to CentOS-4 i386"
in the left upper corner, with the typical navigation key
instructions at the bottom. It just hangs there.
I ping the IP address above, and get no pongs.
Suggestions?
=== Al
Dont you also need a
method=nfs:nfs:10.254.242.33:/vol/updts/staging/CentOS_4.3/ for
anaconda to get loaded?
Just a guess as I haven't done any kickstart installs, so no
flames if I'm talking out of my you know what!
I'm coming to the conclusion that RH, and by extension, CentOS
just won't allow you to use a kickstart file over the network w/o
DHCP.
I can and have used NFS as long as I place the kickstart file on
the CD itself.
That's a pain.
First look at the debugging screens ALT-F3-> ALT-F6. Is the installer
complaining. We mostly use kickstarts via HTTP so I havent tried NFS
in a long while.
The ALT-F2 keys didn't seem to work, and it hung up the install,
though I'm willing to try alternative suggestions. CTL-ALT-F2 does
get me a shell prompt, if I do it during a pause.
What I've finally done is set up a vfat partition on the on the server
itself. That way, when I do a
clearpart --linux
in the ks.cfg it doesn't bother that vfat.
Leaving the ks.cfg on there allows me to try different kickstart
configurations with that server w/o having to make coasters each time.
Once I find kickstarts I like, I don't mind placing them on a CD.
Thanks for the help. Even though I didn't accomplish what
I was originally looking for, I learned a lot trying everyone's
suggestions.
=== Al
I am about 99-44/100% certain that I have successfully done a NFS
kickstart using a fixed address (192.168.1.2) on my humble home
network. I don't think it should matter that I was installing some
version of Fedora Core rather than CentOS. I'll try to find my notes
but don't hold your breath on that one. I do remember that the command
line was LONG and unwieldy.
I am equally certain that I have done a NFS kickstart, letting the IP
be assigned by the DHCP server, with the real (final) IP being
specified in the ks file. That was a LOT easier to do but obviously
required a DHCP server.
The more I think about it, I'm certain I did it with a fixed IP. I
remember now that the big thing I had to wrestle with was using eth1
while letting eth0 just kinda flap in the breeze. I still can't
remember the exact incantation I used, but the answer is on and between
between the lines in the document
file:///usr/share/doc/anaconda-10.1.1.46/kickstart-docs.html, beginning
a bit less than halfway down the page below the heading "network (optional)".
The 1st Corollary to Murphy's Law plainly states that the first time
you do this, it's better if your network is spread out over one desktop
than over one Earth.
Good luck!
|
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
