I tested RAID 1 with differents size hard disk , it is work.
You need first, execute command sfdisk -l /dev/hd_GOOD > partitions.txt
Second execute command sfdisk /dev/hd_NEWDISK < partitons.txt.
After recover process normal RAID recover.
I hope to help you
Adriano Frare
Aleksandar Milivojevic wrote:
Joseph Cheng wrote:
Hello all. I have a server with a linux software raid1 setup between
two drives of the same model....one hard drive as primary ide master
and second hard drive as secondary master. Now primary master hard
drive is displaying a lot of SMART errors so I would like to remove it
and replace with another drive....different brand but same size.
Partitions are /dev/md0 till /dev/md5. I think I know what to do based
on mdadm man page and this list's archives but there is no harm in
confirming right? ;) From this post
http://lists.centos.org/pipermail/centos/2006-April/063076.html I plan
on removing the old partitions from the array like this..... mdadm
/dev/mdx -r /dev/hdax. Then I will shut down the server, replace the
hard drive, make the server boot from second IDE drive and hopefully
boot into Centos. From there do I have to manually create each
/dev/mdx partition and then re-add them like this....mdadm /dev/mdx -a
/dev/hdax ? That is what I am not sure about whether I have to
partiton the drive exactly like the old one or if Centos mdadm can do
some magic for me with a blank drive. TIA!!
Couple of things to watch out.
What boot loader are you using? If it is Grub, check if it was
installed on partition, not in MBR of first drive. If it was in MBR,
there is a good chance you don't have it mirrored on second drive.
You'll need working boot loader (most likely Grub) on second drive in
order to boot from it.
Disk size... It is next to impossible to find "different brand but same
size". If the label says 80GB, it means "somewhere around 80GB". You
want to look at LBA count (it's printed almost on all hard drives, but
often hard to find in specifications). It's basically the number of
sectors that the drive has. You want the drive that has at least the
number of sectors as your existing drive(s). If you already got the new
drive and it is few sectors short, all is not lost. You'll just have a
bit of additional work. You'll need to shrink some partition. Swap
partition is usually good candidate since it doesn't contain any data.
You can also shrink a partition that holds file system, but if you make
mistake you might end up loosing some data. Another thing to keep in
mind when shrinking partitions is that Linux stores RAID metadata at the
end of the partition. If you are shrinking partition that holds Linux
RAID device, the best thing (if it was RAID 1 volume) is to ditch the md
device for it, shrink the file system to smaller size, and recreate md
device. Your data should survive the operation. When shrinking file
system, have in mind you'll need to have some extra space of RAID
metadata information at the end of partition (you'll need to shrink file
system to be smaller than the final partition size).
You'll need to partition the new drive manually. Remember to tag
partitions as "Linux raid autodetect" (by default fdisk will tag them as
"Linux"). Tag for Linux raid autodetect is fd. New partitions must be
the same size (in blocks) as the partitions you are replacing or larger.
If you make them larger, the extra space will be unused.
If your boot loader was installed in the partition, it'll get mirrored
automatically. If it was in MBR, you'll have to install it by hand onto
the drive you just replaced.
The rest should more or less go smooth.
------------------------------------------------------------------------
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
