Hi folks,
Im trying to get a multi-card reader on centos (SD, MMC, and so, 4 card
slots) and i have read (http://www.cs.sfu.ca/~ggbaker/personal/cf-linux)
that CONFIG_SCSI_MULTI_LUN should be enabled on kernel (=Y) but current
34.0.2 doesn't have it enabled by default, is there any particular
reason to not be enabled?
By the other hand i've also tweak the /etc/grub.conf file to boot the
kernel with max_luns=32 and results are the same, only scsc lun=0 is
recognized.
At the same time using the workaround mentioned in the link pasted b4
regarding to modify the /etc/modules.conf to include 'options scsi_mod
max_scsi_luns=8' gives the same results, no detection at all for the
card slots.
[root@sparkbox ~]# cat /proc/bus/usb/devices
T: Bus=01 Lev=01 Prnt=01 Port=06 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0644 ProdID=0200 Rev= 4.00
S: Manufacturer=TEAC
S: Product=CA-200
S: SerialNumber=0000020307B2
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-
storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
and /var/log/dmesg still shows:
<...>
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: TEAC Model: USB HS-CF Card Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdc at scsi3, channel 0, id 0, lun 0
USB Mass Storage device found at 7
<...>
Instead of (if i understand well for this scsi3 line) after a
[root@sparkbox]# sg_scan -i (it should show)
/dev/sg2: scsi3 channel=0 id=0 lun=0 [em] type=0
Generic STORAGE DEVICE 0128 [wide=0 sync=0 cmdq=0 sftre=0
pq=0x0]
/dev/sg3: scsi3 channel=0 id=0 lun=1 [em] type=0
Generic STORAGE DEVICE 0128 [wide=0 sync=0 cmdq=0 sftre=0
pq=0x0]
/dev/sg4: scsi3 channel=0 id=0 lun=2 [em] type=0
Generic STORAGE DEVICE 0128 [wide=0 sync=0 cmdq=0 sftre=0
pq=0x0]
/dev/sg5: scsi3 channel=0 id=0 lun=3 [em] type=0
Generic STORAGE DEVICE 0128 [wide=0 sync=0 cmdq=0 sftre=0
pq=0x0]
But actually,
[root@sparkbox ~]# sg_scan -i
[root@sparkbox ~]# (shows nothing)
And
[root@sparkbox ~]# sg_map
Stopping because no sg devices found
Strange, could not find device /dev/sda mapped to sg device??
Strange, could not find device /dev/sdb mapped to sg device??
Strange, could not find device /dev/sdc mapped to sg device??
Strange, could not find device /dev/sdd mapped to sg device??
Looking at SCSI:
[root@sparkbox ~]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: HDS728080PLA380 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: Genesys Model: USB to IDE Disk Rev: 0002
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: TEAC Model: USB HS-CF Card Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi4 Channel: 00 Id: 00 Lun: 00
Vendor: Model: USB DISK Pro Rev: 1.1b
Type: Direct-Access ANSI SCSI revision: 02
And finally doing the last workaround found in the link from Greg Baker
article for my scsi3 chain:
[root@sparkbox ~]#echo >/proc/scsi/scsi "scsi add-single-device 3 0 0 1"
[root@sparkbox ~]#echo >/proc/scsi/scsi "scsi add-single-device 3 0 0 2"
[root@sparkbox ~]#echo >/proc/scsi/scsi "scsi add-single-device 3 0 0 3"
Solves the identification:
[root@sparkbox ~]# cat /proc/scsi/scsi
Attached devices:
<...>
Host: scsi3 Channel: 00 Id: 00 Lun: 00
Vendor: TEAC Model: USB HS-CF Card Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi3 Channel: 00 Id: 00 Lun: 01
Vendor: TEAC Model: USB HS-xD/SM Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi3 Channel: 00 Id: 00 Lun: 02
Vendor: TEAC Model: USB HS-MS Card Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi3 Channel: 00 Id: 00 Lun: 03
Vendor: TEAC Model: USB HS-SD Card Rev: 4.00
Type: Direct-Access ANSI SCSI revision: 02
Now, even without update the udev rules with a new rule It seems to work
after inserting the SD (1GB card) card on card-reader, from dmesg:
<...>
SCSI device sdg: 2012160 512-byte hdwr sectors (1030 MB)
sdg: Write Protect is off
sdg: Mode Sense: 23 00 00 00
sdg: assuming drive cache: write through
SCSI device sdg: 2012160 512-byte hdwr sectors (1030 MB)
sdg: Write Protect is off
sdg: Mode Sense: 23 00 00 00
sdg: assuming drive cache: write through
sdg: sdg1
<...>
Mounting the correct SD card on fstab and only remaining to update
permissions/udev or pamconsole (not sure where) to get RW access for
user space.
Hope it helps and just to clarify for mentionned CONFIG_SCSI_MULTI_LUN
option in kernel.
Jose.
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
