Shutting down interface eth0: [ OK ]
Shutting down loopback interface: [ OK ]
Setting network parameters: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0: [ OK ]
Bringing up interface eth1: 3c59x device eth1 does not seem to be present, delaying initialization.
[FAILED]
here's my alias on /etc/modprobe.conf
alias eth1 3c59x
On 8/2/06,
Mark Quitoriano <markquitoriano@xxxxxxxxx> wrote:
hmmm... it still show devXXXX but when ir estart the server it gets the right ip. but how come it still shows the dev10671 and not eth1.
dev10671 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
inet addr: xxx.xxx.xxx.xxx Bcast:xxx.xxx.xxx.xxx Mask:xxx.xxx.xxx.xxxinet6 addr: xxxxxxxxxxxxxx Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:1845 errors:0 dropped:0 overruns:1 frame:0
TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2267861 (2.1 MiB) TX bytes:76680 (74.8 KiB)
Interrupt:11 Base address:0xdf00On 8/1/06, William L. Maltby < BillsCentOS@xxxxxxxxxxxx> wrote:On Mon, 2006-07-31 at 20:19 +0200, Alexander Dalloz wrote:
> Mark Quitoriano schrieb:
>
> > Hi list,
> >
> > i have a problem in one of my centos boxes. I installed CentOS 4.3. I
> > addedd
> > additionl interface card in this server and when i execute ifconfig
> > command
> > i see devNNN(where n is a random number). And when i restart the
> > server the
> > NNNN always change.
> >
> >
> > dev9926 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
> > inet addr:xxx.xxx.xxx.xxx Bcast:xxx.xxx.xxx.xxx Mask:
> > xxx.xxx.xxx.xxx
> > inet6 addr: xxxxxxxxxxxxxxx Scope:Link
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:8304 errors:0 dropped:0 overruns:1 frame:0
> > TX packets:3848 errors:0 dropped:0 overruns:0 carrier:1
> > collisions:0 txqueuelen:1000
> > RX bytes:937839 (915.8 KiB) TX bytes:351719 (343.4 KiB)
> > Interrupt:11 Base address:0xdf00
>
> Make sure you have a valid /etc/sysconfig/network-scripts/ifcfg-<device>
> (<device> may be eth1) and set an alias for that device in
> /etc/modprobe.conf.
ACK! I didn't think he might not have an alias! Standard system
installation puts one in. If he is adding another NIC and it is not the
same type as what is there already, he would need to add, as you say.
>
> Alexander
> <snip sig stuff>
--
Bill-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (GNU/Linux)
iD8DBQBEzmGL/1DcCJj5ZgkRAgDzAKDqdVdrdkVw4fC/gzfz76BDyQB8pACdETTW
iqxGJVr/EWR7aC9m9Iq6MYk=
=zMAA
-----END PGP SIGNATURE-----
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos
--
Regards,
Mark Quitoriano, CCNA
Fan the flame...
http://www.spreadfirefox.com/?q=user/register&r=19441
--
Regards,
Mark Quitoriano, CCNA
Fan the flame...
http://www.spreadfirefox.com/?q=user/register&r=19441
_______________________________________________ CentOS mailing list CentOS@xxxxxxxxxx http://lists.centos.org/mailman/listinfo/centos
