On Tue, 2006-05-02 at 17:56 -0700, Steven Vishoot wrote:
>
> --- Craig White <craigwhite@xxxxxxxxxxx> wrote:
>
> > I have an issue with cdrecord though and I can't
> > figure it out. I use
> > Webmin, which basically just creates an iso and then
> > uses cdrecord to
> > burn it and it worked fine with previously installed
> > CentOS 4 (I wiped
> > and reinstalled about 8 months ago).
> >
> > This is the command that Webmin tries to execute...
> >
> > cdrecord -v dev=0,0,0 speed=4 -isosize \
> > '/home/Linux/CentOS-4/CentOS-4.2-i386-bin4of4.iso'
> >
> > The result of cdrecord -scanbus at bottom of email.
> > Log of error just
> > below.
> >
> > Help appreciated...
> >
> > Craig
> >
> > cdrecord: No write mode specified.
> > cdrecord: Asuming -tao mode.
> > cdrecord: Future versions of cdrecord may have
> > different drive dependent defaults.
> > cdrecord: Continuing in 5 seconds...
> > scsidev: '0,0,0'
> > scsibus: 0 target: 0 lun: 0
> > cdrecord: No such file or directory. Cannot open
> > '/dev/pg0'. Cannot open SCSI driver.
> > cdrecord: For possible targets try 'cdrecord
> > -scanbus'.
> > cdrecord: For possible transport specifiers try
> > 'cdrecord dev=help'.
> > Cdrecord-Clone 2.01-dvd (i686-pc-linux-gnu)
> > Copyright (C) 1995-2004 J??rg Schilling
> > Note: This version is an unofficial (modified)
> > version with DVD support
> > Note: and therefore may have bugs that are not
> > present in the original.
> > Note: Please send bug reports or support requests to
> > http://bugzilla.redhat.com/bugzilla
> > Note: The author of cdrecord should not be bothered
> > with problems in this version.
> > TOC Type: 1 = CD-ROM
> >
> > # cdrecord -scanbus
> > Cdrecord-Clone 2.01-dvd (i686-pc-linux-gnu)
> > Copyright (C) 1995-2004 J???rg
> > Schilling
> > Note: This version is an unofficial (modified)
> > version with DVD support
> > Note: and therefore may have bugs that are not
> > present in the original.
> > Note: Please send bug reports or support requests to
> > http://bugzilla.redhat.com/bugzilla
> > Note: The author of cdrecord should not be bothered
> > with problems in
> > this version.
> > scsidev: 'ATA'
> > devname: 'ATA'
> > scsibus: -2 target: -2 lun: -2
> > Linux sg driver version: 3.5.27
> > Using libscg version 'schily-0.8'.
> > cdrecord: Warning: using inofficial libscg transport
> > code version
> > (schily - Red Hat-scsi-linux-sg.c-1.83-RH
> > '@(#)scsi-linux-sg.c
> > 1.83 04/05/20 Copyright 1997 J. Schilling').
> > scsibus0:
> > 0,0,0 0) 'COMBI ' 'RW16x10/DVD '
> > 'H1.1' Removable
> > CD-ROM
> > 0,1,0 1) *
> > 0,2,0 2) *
> > 0,3,0 3) *
> > 0,4,0 4) *
> > 0,5,0 5) *
> > 0,6,0 6) *
> > 0,7,0 7) *
> >
> >
> > _______________________________________________
> > CentOS mailing list
> > CentOS@xxxxxxxxxx
> > http://lists.centos.org/mailman/listinfo/centos
> >
> craig,
>
> the only time i have had troubles like that is when
> the ide-cd would load before the ide-scsi. check to
> see if both ide-scsi and ide-cd are loaded....but not
> sure if this is your problem.. can not remember if i
> was able to see the drive when this happened to me.
----
neither were loaded according to lsmod
I modprobed ide-scsi (didn't change anything)
same error as above
I modprobed ide-cd (error)
# modprobe ide-cd
FATAL: Module ide_cd not found.
Craig
