Re: Qemu - enabling "bridge mode" for primary physical interface for VMs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



Thank you Chris Adams for excellent information! It worked, see below. 

On Tuesday, December 7, 2021 8:25:37 PM PST Chris Adams wrote:
> Once upon a time, Lists <lists@xxxxxxxxxxxxxxxxxx> said:
> > I understand that it's possible to allow the 4 VM guest systems to each
> > have a "direct" fixed IP address and access the addresses \via the host
> > network adapter, while the host retains its fixed IP.
> 
> If you are running NetworkManager (the default), it's not too hard.
> Here's an example step-by-step for changing an existing interface "em1" to
> be a bridge "br0":
> 
> 
> # Create a bridge interface
> nmcli con add type bridge ifname br0 bridge.stp no
> 
> # Copy all the IPv4/IPv6 config from an existing interface
> nmcli con mod bridge-br0 $(nmcli -f
> ipv4.method,ipv4.addresses,ipv4.gateway,ipv6.method,ipv6.addresses,ipv6.gat
> eway con show em1 | grep -v -- -- | sed 's/:  */ /') # -or- just set an IPv4
> address/gateway to known values
> nmcli con mod bridge-br0 ipv4.method manual ipv4.address 10.1.1.2/24
> ipv4.gateway 10.1.1.1 ipv6.method ignore
> 
> # Make a connection for the physical ethernet em1 to be part of the bridge
> nmcli con add type ethernet ifname em1 master bridge-br0
> 
> # Switch from the "regular" em1 to the bridge
> nmcli con down em1; nmcli con up bridge-br0; nmcli con up bridge-slave-em1
> 
> # Disable the original config
> nmcli con mod em1 autoconnect 0
> 
> 
> Then you set your VMs to use the bridge - in the libvirt XML for
> example, you'd have something like:
> 
>     <interface type='bridge'>
>       <mac address='52:54:00:12:34:56'/>
>       <source bridge='br0'/>
>       <model type='virtio'/>
>       <address type='pci' domain='0x0000' bus='0x00' slot='0x03'
> function='0x0'/> </interface>
> 
> 
> Inside the VM, configure the interface just as if it was a physical system
> on that subnet.

I just wanted to say that this worked, exactly as shown, and after trying it 
once on development hardward, I tried it on a production server and it also 
worked with minimal hassle. 

I ran into an oddity because the software image of the production server was 
from a disk image, not a fresh install and I had to wrestle with some "Network 
Adapters" that no longer really existed. My advice to anybody trying this 
would be to go into Network Manager and ensure the following before starting: 

1) Set up the server to manual IP addresses, not DHCP. 
2) Remove all duplicitous or inactive network adapters and interfaces. 
3) Make sure that in nmtui, that all editable connection(s) also show in the 
interface that lets you activate them.
4) Make sure you are not dependent on the network adapter you are trying to 
use to contact the server! In my case I ended up falling back to IPMI. Minor 
issue because I had it available, could have been far worse if I hadn't. 

... and then do the above. 

Ben S

Attachment: signature.asc
Description: This is a digitally signed message part.

_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos

[Index of Archives]     [CentOS]     [CentOS Announce]     [CentOS Development]     [CentOS ARM Devel]     [CentOS Docs]     [CentOS Virtualization]     [Carrier Grade Linux]     [Linux Media]     [Asterisk]     [DCCP]     [Netdev]     [Xorg]     [Linux USB]


  Powered by Linux