Mark Haney wrote:
To be honest, I'd not try a btrfs volume on a notebook SSD. I did that on a
couple of systems and it corrupted pretty quickly. I'd stick with xfs/ext4
if you manage to get the drive working again.
That was merely to see if a trim operation on the whole device would bring some
improvement.
I have the system on SSDs at home and data on spinning disks, so far no problems
with btrfs. Do I need to worry now?
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon>
Virus-free.
www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
On Wed, Aug 9, 2017 at 1:48 PM, hw <hw@xxxxxxxx> wrote:
Robert Moskowitz wrote:
I am building a new system using an Kingston 240GB SSD drive I pulled
from my notebook (when I had to upgrade to a 500GB SSD drive). Centos
install went fine and ran for a couple days then got errors on the
console. Here is an example:
[168176.995064] sd 0:0:0:0: [sda] tag#14 FAILED Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168177.004050] sd 0:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 01 04 68 b0
00 00 08 00
[168177.011615] blk_update_request: I/O error, dev sda, sector 17066160
[168487.534510] sd 0:0:0:0: [sda] tag#17 FAILED Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168487.543576] sd 0:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 01 04 68 b0
00 00 08 00
[168487.551206] blk_update_request: I/O error, dev sda, sector 17066160
[168787.813941] sd 0:0:0:0: [sda] tag#20 FAILED Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[168787.822951] sd 0:0:0:0: [sda] tag#20 CDB: Read(10) 28 00 01 04 68 b0
00 00 08 00
[168787.830544] blk_update_request: I/O error, dev sda, sector 17066160
Eventually, I could not do anything on the system. Not even a 'reboot'.
I had to do a cold power cycle to bring things back.
Is there anything to do about this or trash the drive and start anew?
Make sure the cables and power supply are ok. Try the drive in another
machine
that has a different controller to see if there is an incompatibility
between
the drive and the controller.
You could make a btrfs file system on the whole device: that should say
that
a trim operation is performed for the whole device. Maybe that helps.
If the errors persist, replace the drive. I悲 use Intel SSDs because they
seam to have the least problems with broken firmwares. Do not use SSDs
with
hardware RAID controllers unless the SSDs were designed for this
application.
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos
_______________________________________________
CentOS mailing list
CentOS@xxxxxxxxxx
https://lists.centos.org/mailman/listinfo/centos
